01-15-2021 12:55 AM - edited 07-05-2021 01:01 PM
Hello guys,
it is good some time to don't jshare only issue, but to get some hints to do the things in a better way.
I swapped my other access point with this ap3702 that run with autonomous image and all is working VERY GOOD.
If you have time, do you think that this config is optimized for 802.11 ac?
! ! No configuration change since last restart version 15.3 no service pad service timestamps debug datetime msec service timestamps log datetime localtime show-timezone no service password-encryption ! hostname ap3702 ! ! logging buffered 20000 informational logging rate-limit console 9 enable secret 9 XXXX ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! ! ! ! aaa session-id common clock timezone CET 1 0 clock summer-time DST recurring last Sun Mar 2:00 last Sun Oct 3:00 clock save interval 8 no ip source-route no ip cef ip name-server 192.168.1.1 ! ! ! ! dot11 pause-time 100 dot11 syslog ! dot11 ssid --Caos-WiFi-C--2.4GHz authentication open authentication key-management wpa version 2 guest-mode wpa-psk ascii 0 xxx ! dot11 ssid --Caos-WiFi-C--5GHz authentication open authentication key-management wpa version 2 guest-mode wpa-psk ascii 0 xxxx ! ! ! no ipv6 cef ! ! archive log config hidekeys path flash:/archive/ maximum 12 write-memory time-period 10080 memory free low-watermark processor 19000 memory free low-watermark IO 19000 username xxx privilege 15 secret 9 xxxxx ! ! ip tftp blocksize 8192 bridge irb ! ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid --Caos-WiFi-C--2.4GHz ! antenna gain 4 speed 12.0 basic-18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23. packet retries 32 drop-packet channel 2472 station-role root beacon privacy guest-mode world-mode dot11d country-code IT indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid --Caos-WiFi-C--5GHz ! antenna gain 4 peakdetect no dfs band block speed basic-12.0 18.0 basic-24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23. a1ss9 a2ss9 a3ss9 packet retries 32 drop-packet packet max-retries 3 0 fail-threshold 100 500 priority 5 drop-packet packet max-retries 3 0 fail-threshold 100 500 priority 6 drop-packet channel width 80 channel 5260 station-role root beacon privacy guest-mode dot11 qos class background local cw-min 6 fixed-slot 10 ! dot11 qos class video local cw-max 5 fixed-slot 3 transmit-op 0 ! dot11 qos class voice local cw-max 4 transmit-op 0 ! dot11 qos class background cell cw-min 8 fixed-slot 12 ! dot11 qos class best-effort cell cw-min 6 fixed-slot 5 ! dot11 qos class video cell cw-min 4 cw-max 6 fixed-slot 5 transmit-op 0 ! dot11 qos class voice cell cw-max 4 transmit-op 0 ! world-mode dot11d country-code IT indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface GigabitEthernet0 no ip address duplex auto speed auto bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning ! interface BVI1 mac-address a89d.218a.64c0 ip address 192.168.1.2 255.255.255.0 ! ip default-gateway 192.168.1.1 ip forward-protocol nd ip http server no ip http secure-server ip http timeout-policy idle 600 life 86400 requests 60 ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag ip ssh version 2 ! logging source-interface BVI1 no cdp run ! ! bridge 1 route ip ! ! alias exec qos0 show policy-map interface dot11Radio 0.1 alias exec qos1 show policy-map interface dot11Radio 1.1 alias exec busy0 dot11 dot11Radio 0 carrier busy alias exec busy1 dot11 dot11Radio 1 carrier busy alias exec asso sh dot11 associations ! line con 0 privilege level 15 no activation-character line vty 0 4 access-class 80 in exec-timeout 30 0 length 0 transport preferred ssh transport input ssh transport output telnet ! exception memory ignore overflow processor exception memory ignore overflow io sntp server 192.168.1.1 sntp source-interface BVI1 end
Thank you for your time.
01-15-2021 06:36 AM
Yes I think this configuration should provide 802.11ac data rates.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide