cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2715
Views
0
Helpful
11
Replies

Cannot prime AIR-CAP2702I-UXK9

dderbowka
Level 1
Level 1

I purchased a AIR-CAP2702I-UXK9.

I am trying to prime the AP but the controller will not allow it to accociate because the Country is not set. 

 

Is it possible to configure the country via the CLI? 

Thanks!

11 Replies 11

Sandeep Choudhary
VIP Alumni
VIP Alumni

paste the info here:

 

sh sysinfo from WLC

also the logs(bootup process) from AP console..

 

More info about priming heer.

https://www.speaknetworks.com/cisco-universal-wireless-ap-provisioning-and-priming/

 

Regards

Dont forget to rate helpful posts

 

Will do the AP first!

Here is the CLI messages upon the AP Boot. Will Show the controller next. 


IOS Bootloader - Starting system.
flash is writable
Antigua Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 70 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 21159424
flashfs[0]: Bytes available: 19999232
flashfs[0]: flashfs fsck took 10 seconds.
Base Ethernet MAC address: f4:cf:e2:a4:db:1c
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-mx.153-3.JA12"...#########################

File "flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-mx.153-3.JA12" uncompressed and installed, entry point: 0x2003000
executing...

Secondary Bootloader - Starting system.
Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 70 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 21159424
flashfs[0]: Bytes available: 19999232
flashfs[0]: flashfs fsck took 11 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 0 seconds.
Base Ethernet MAC address: f4:cf:e2:a4:db:1c
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-xx.153-3.JA12;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-xx.153-3.JA12"...################################################
File "flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-xx.153-3.JA12" uncompressed and installed, entry point: 0x1003000
executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

 

Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JA12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Fri 20-Oct-17 20:51 by prod_rel_team

Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...

flashfs[2]: 70 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 21159424
flashfs[2]: Bytes available: 19741184
flashfs[2]: flashfs fsck took 12 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.

Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)

POWER TABLE FILENAME = ram:/U2.bin

Radio1 present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/U5.bin

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-AP2702I-UXK9 (PowerPC) processor (revision A0) with 376814K/134656K bytes of memory.
Processor board ID FCW1904PC1W
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.152.0
Access Point Type: World Mode
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:CF:E2:A4:DB:1C
Part Number : 73-15824-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC1902608Q
Top Assembly Part Number : 068-100395-01
Top Assembly Serial Number : FCW1904PC1W
Top Revision Number : A0
Product/Model Number : AIR-AP2702I-UXK9
% Please define a domain-name first.


Press RETURN to get started!


*Mar 1 00:00:16.959: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:17.419: Registering HW DTLS

*Mar 1 00:00:17.427: APAVC: Initial WLAN Buffers Given to System is 2500

*Mar 1 00:00:17.475: APAVC: WlanPAKs 42878 RadioPaks 42270

*Mar 1 00:00:17.475: Starting Ethernet promiscuous mode
*Mar 1 00:00:19.791: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:19.791: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:23.743: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:23.855: loading Power Tables from ram:/U2.bin. Class = A
*Mar 1 00:00:23.855: record size of 3ss: 1168 read_ptr: 4B6801E

*Mar 1 00:00:28.899: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:28.943: loading Power Tables from ram:/U5.bin. Class = A
*Mar 1 00:00:28.943: record size of vht: 2904 read_ptr: 4B6801E

*Mar 1 00:00:29.103: Wait until the stile protocol list is initialized.

*Mar 1 00:00:30.307: Start STILE Activation

*Mar 1 00:00:32.319: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:32.319: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar 1 02:56:43.027: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JA12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Fri 20-Oct-17 20:51 by prod_rel_team
*Mar 1 02:56:43.027: %SNMP-5-COLDSTART: SNMP agent on host APf4cf.e2a4.db1c is undergoing a cold start
*Mar 1 02:56:43.295: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Mar 1 02:56:44.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 02:56:45.171: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully

*Mar 1 02:56:45.331: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 02:56:45.331: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 02:56:45.331: %LINK-5-CHANGED: Interface GigabitEthernet1, changed state to administratively down
*Mar 1 02:56:46.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 02:56:46.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 02:56:55.307: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 02:56:56.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 02:56:58.019: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 02:56:58.019: DPAA Initialization Complete
*Mar 1 02:56:58.019: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 02:56:59.019: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 02:57:01.019: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 02:57:01.475: Currently running a Release Image

*Mar 1 02:57:01.895: Using SHA-2 signed certificate for image signing validation.
*Mar 1 02:57:02.183: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 02:57:02.583: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.0.0.7, mask 255.255.255.192, hostname APf4cf.e2a4.db1c

*Mar 1 02:57:08.467: APAVC: Succeeded to activate all the STILE protocols.

*Mar 1 02:57:08.467: APAVC: Registering with CFT

*Mar 1 02:57:08.467: APAVC: CFT registration of delete callback succeeded

*Mar 1 02:57:08.467: APAVC: Reattaching Original Buffer pool for system use

*Mar 1 02:57:08.467: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 02:57:16.035: AP image integrity check PASSED

*Mar 1 02:57:16.135: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 02:57:17.231: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 02:57:17.239: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 02:57:18.231: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 02:57:18.459: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 02:57:19.459: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%Error opening flash:/capwap-saved-config (No such file or directory)
%Error opening flash:/capwap-saved-config-bak (No such file or directory)
*Mar 1 02:57:26.139: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 0 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER.CISCO.ADS"...domain server (10.0.0.2)

*Mar 1 02:57:48.147: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 6 16:20:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:20:40.443: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:20:40.447: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.0.60
*Sep 6 16:20:59.919: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.0.60:5246
*Sep 6 16:21:00.007: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 6 16:21:00.007: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 6 16:21:00.011: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 6 16:21:00.043: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 6 16:21:01.011: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 6 16:21:01.039: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 6 16:21:01.047: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 6 16:21:02.031: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 6 16:21:02.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 6 16:21:02.067: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 6 16:21:02.075: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 6 16:21:02.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 6 16:21:03.067: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 6 16:21:03.075: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 6 16:21:03.103: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 6 16:21:04.103: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 6 16:21:10.039: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 6 16:21:10.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:21:10.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:21:10.435: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.0.60
*Sep 6 16:21:28.699: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.0.60:5246
*Sep 6 16:21:28.783: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 6 16:21:28.783: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 6 16:21:28.791: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 6 16:21:28.811: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 6 16:21:29.787: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 6 16:21:29.815: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 6 16:21:29.823: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 6 16:21:30.807: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 6 16:21:30.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 6 16:21:30.843: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 6 16:21:30.851: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 6 16:21:30.859: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 6 16:21:31.843: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 6 16:21:31.851: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 6 16:21:31.879: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 6 16:21:32.879: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 6 16:21:38.811: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 6 16:21:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:21:39.443: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:21:39.443: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.0.60
*Sep 6 16:21:57.711: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.0.60:5246
*Sep 6 16:21:57.795: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 6 16:21:57.795: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 6 16:21:57.799: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 6 16:21:57.823: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 6 16:21:58.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 6 16:21:58.827: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 6 16:21:58.835: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 6 16:21:59.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 6 16:21:59.827: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 6 16:21:59.855: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 6 16:21:59.863: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 6 16:21:59.871: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 6 16:22:00.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 6 16:22:00.863: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 6 16:22:00.891: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 6 16:22:01.891: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 6 16:22:07.823: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Sep 6 16:22:07.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:22:07.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.0.60 peer_port: 5246
*Sep 6 16:22:07.439: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.0.60
*Repeats*

And the WLC:

Verifying boot loader integrity... OK.

OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)
CPU Cores: 4
DRAM: 1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1, octeth2, octeth3
' - Active interface
E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
- Model: 1GB CompactFlash Card Firm: CF B612J Ser#: A191103699A10A2E09dG
- Type: Hard Disk
- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)


Press <ESC> now to access the Boot Menu...

Loading primary image (8.0.152.0)
100%

38323276 bytes read
Launching...
Launching images...
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 688, tty '': '/etc/init.d/rcS'
/etc/init.d/rcS: line 5: cannot create /proc/sys/net/ipv4/ip_no_pmtu_disc: nonexistent directory
Detecting Hardware ...
Installing ether-pow driver - 0x6008
starting pid 867, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'
Setting up ZVM
Exporting LD_LIBRARY_PATH
Decompressing...
Validating...... OK

Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
octeon_device_init: found 1 DPs
/dev/fpga: No such device or address
readCPUConfigData: cardid 0x6060001
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version 8.0.152.0
Firmware Version PIC 20.0


Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services:
License daemon start initialization.....
ok

License daemon running.....
Starting Statistics Service: ok
Starting Licensing Services: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU0.00: Initializing last packet received queue. Num of cores(2)
Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU0.00: Core 0 Initialization: ok
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing Timer...done.
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing NBAR AGING Timer...done.
Fastpath CPU0.01: Core 1 Initialization: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting Management Frame Protection: ok
Starting DNS Services: ok
Starting Redundancy: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Capwap Ping Component: ok
Starting AVC Services: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting RF Profiles: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting SXP Services: ok
Starting Alarm Services: ok
Starting FMC HS: ok
Starting IPv6 Services: ok
Starting Config Sync Manager : ok
Starting Hotspot Services: ok
Starting Portal Server Services: ok
Starting mDNS Services: ok
Starting Management Services:
Web Server: CLI: Secure Web: disabled.

(Cisco Controller)

Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)

Also the sh sysinfo command:
(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.0.152.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 20.0


Build Type....................................... DATA + WPS

System Name...................................... CISCT2504
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.0.0.60
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 29 mins 13 secs
System Timezone Location......................... (GMT -6:00) Central Time (US and Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

--More-- or (q)uit

Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 4800 rpm

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 13

Burned-in MAC Address............................ 6C:FA:89:DA:32:40
Maximum number of APs supported.................. 75
System Nas-Id....................................
WLC MIC Certificate Types........................ SHA1/SHA2

For reference on the controller

Leo Laohoo
Hall of Fame
Hall of Fame
You will need to download the smarphone app.

I have it but unless the AP is willing to join the controller, its not an option.

Hi there,

 

I got the same issue with virtual wireless controller version 8.8.111.0 and an AIR-AP2702E-UXK9 and software Version 15.3(3)JI4.

After factory reset ap joins and downloads primary software image, but after reload not joined and error:

 

Lwapp configuration request rejected

Regulatory domain check has failed for the AP

 

No priming with app nor automatic with another primed AP is working as it can´t be seen any longer in wlc onsole. I don´t know what to do now.

 

Thanks.

 

 

Do not use 8.8.111.0.

Thanks.

I tested also with the latest Version

Release 8.8.120.0 ED

But no luck so back to 8.8.111.0. And then after another time deletion of capwap-saved-config and lwapp_ssc_token.cfg suddenly he got primed by NDR from another webapp primed AP and joined to wlc successfully.

What a crazy development by Cisco. I wouldn´t recommend to buy any universal APs anymore.

 

Thanks a lot.

This means you need to re-prime the AP for UX.
Don't use 8.8.111.0 or you'll have troubles.
Review Cisco Networking for a $25 gift card