Catalyst 9130AX AP booting into WNC Linux instead of IOS XE

Kurian Thampy · ‎09-05-2021

I have a new Catalyst 9130AX AP which boots into WNC Linux instead of IOS XE. The LED does not work and neither does the factory reset procedure.

If I interrupt auto boot by pressing a key, it goes to a U-Boot like shell called "Axel". I've posted "printenv" output from the Linux shell and the "Axel" shell.

How do I install either CAPWAP or EWC images on this AP?

Linux boot:

Spoiler

BootROM - 2.03
Starting AP IOROM 1.02
Booting from SPI NOR flash 0
Found valid image at boot postion 0x000
lNOTICE:  Starting binary extension
NOTICE:  SVC: SVC is not supported on AP807
NOTICE:  Gathering DRAM information
mv_ddr: mv_ddr-devel-18.07.0-g2aa16c5-dirty (Aug 24 2018 - 11:16:22)
Synopsys DDR43 PHY Firmware version: 0.73a
SNPS DDR: 1D training passed
SNPS DDR: 2D training passed
SNPS DDR: training completed
mv_ddr: completed successfully
NOTICE:  Cold boot
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.4(debug):devel-18.07.2:2aa16c5-dirty
NOTICE:  BL1: Built : 11:16:24, Aug 24 2018
NOTICE:  BL1: Booting BL2
lNOTICE:  BL2: v1.4(debug):devel-18.07.2:2aa16c5-dirty
NOTICE:  BL2: Built : 11:16:26, Aug 24 2018
NOTICE:  BL1: Booting BL31
lNOTICE:  MSS PM is not supported in this build
NOTICE:  BL31: v1.4(debug):devel-18.07.2:2aa16c5-dirty
NOTICE:  BL31: Built : 11:16:29, Aug 24 2018
l

U-Boot 2017.03-armada-18.07.1 - WNC RXAM-C1.MRVL V1.0.8.2 (Aug 24 2018 - 11:15:41 +0800)

Model: Marvell Armada 3900 AXIS-BT board
SoC: Armada3900-A1; AP807-A1; CP115-A0
Clock:  CPU     1600 [MHz]
        DDR     1200 [MHz]
        FABRIC  1200 [MHz]
        MSS     200  [MHz]
LLC Disabled
DRAM:  2 GiB
U-Boot DT blob at : 000000007f6eac60
setup_gpio rxam-c1 SGE
NAND_USE_FLASH_BBT (in last 8 blocks)
Comphy chip #0:
Comphy-0: PEX0          5 Gbps
Comphy-1: UNCONNECTED
Comphy-2: SFI0          10.3125 Gbps
Comphy-3: UNCONNECTED
Comphy-4: UNCONNECTED
Comphy-5: UNCONNECTED
UTMI PHY 0 initialized to USB Host0
PCIE-0: Link down
NAND:  1024 MiB
MMC:
Net:   eth0: mvpp2-0 [PRIME]
XFI: xfi_xsmi_init f2122834=4B78
XFI: xfi_xsmi_init f21228f4=30B4
XSMI: xfi_xsmi_init f212a60c=2E
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x0, size 0x100000
 1048576 bytes read: OK

NAND read: device 0 offset 0x100000, size 0x1200000
 18874368 bytes read: OK
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
   Using Device Tree in place at 0000000001000000, end 000000000100b02f

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 4.4.120-devel-18.07.0  (joseph@d2r120h) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #1 SMP PREEMPT Fri Aug 24 11:13:35 CST 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd083]
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 256 MiB at 0x000000005c000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] PERCPU: Embedded 16 pages/cpu @ffffffc05bf81000 s24960 r8192 d32384 u65536
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515584
[    0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=11,4096 root=ubi0:rootfs rootfstype=ubifs rw chk_data_crc rootdelay=2
[    0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] log_buf_len min size: 16384 bytes
[    0.000000] log_buf_len: 32768 bytes
[    0.000000] early log buf free: 14744(89%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] software IO TLB [mem 0x55a00000-0x59a00000] (64MB) mapped at [ffffffc055a00000-ffffffc0599fffff]
[    0.000000] Memory: 1388700K/2095104K available (9608K kernel code, 555K rwdata, 3248K rodata, 352K init, 277K bss, 444260K reserved, 262144K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0000000 - 0xffffffbdc2000000   (    32 MB actual)
[    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc080000000   (  2048 MB)
[    0.000000]       .init : 0xffffffc000d11000 - 0xffffffc000d69000   (   352 KB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc000d10164   ( 12865 KB)
[    0.000000]       .data : 0xffffffc000d82000 - 0xffffffc000e0ce00   (   556 KB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GICv2m: Overriding V2M MSI_TYPER (base:160, num:32)
[    0.000000] GICv2m: Node v2m: range[0xf0280000:0xf0280fff], SPI[160:192]
[    0.000000] GICv2m: Overriding V2M MSI_TYPER (base:192, num:32)
[    0.000000] GICv2m: Node v2m: range[0xf0290000:0xf0290fff], SPI[192:224]
[    0.000000] GICv2m: Overriding V2M MSI_TYPER (base:224, num:32)
[    0.000000] GICv2m: Node v2m: range[0xf02a0000:0xf02a0fff], SPI[224:256]
[    0.000000] GICv2m: Overriding V2M MSI_TYPER (base:256, num:32)
[    0.000000] GICv2m: Node v2m: range[0xf02b0000:0xf02b0fff], SPI[256:288]
[    0.000000] mvebu-pic: registered with 19 irqs
[    0.000000] mvebu-sei: registered with 64 irqs
[    0.000000] mvebu-mci-irq: mvebu_mci_of_init total ports 2 registered with 16 irqs
[    0.000000] Architected cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.000106] Console: colour dummy device 80x25
[    0.000116] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[    0.000122] pid_max: default: 32768 minimum: 301
[    0.000151] Security Framework initialized
[    0.000170] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000173] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000452] Initializing cgroup subsys memory
[    0.000466] Initializing cgroup subsys hugetlb
[    0.000598] EFI services will not be available.
[    0.000611] ASID allocator initialised with 65536 entries
[    0.036252] Detected PIPT I-cache on CPU1
[    0.036280] CPU1: Booted secondary processor [410fd083]
[    0.048260] Detected PIPT I-cache on CPU2
[    0.048282] CPU2: Booted secondary processor [410fd083]
[    0.060271] Detected PIPT I-cache on CPU3
[    0.060286] CPU3: Booted secondary processor [410fd083]
[    0.060317] Brought up 4 CPUs
[    0.060328] SMP: Total of 4 processors activated.
[    0.060334] CPU: All CPU(s) started at EL2
[    0.060610] devtmpfs: initialized
[    0.063503] DMI not present or invalid.
[    0.063632] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.063645] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.066723] xor: measuring software checksum speed
[    0.104081]    8regs     :  6412.000 MB/sec
[    0.144103]    8regs_prefetch:  5620.000 MB/sec
[    0.184126]    32regs    :  7542.000 MB/sec
[    0.224150]    32regs_prefetch:  6304.000 MB/sec
[    0.224153] xor: using function: 32regs (7542.000 MB/sec)
[    0.224162] pinctrl core: initialized pinctrl subsystem
[    0.224698] NET: Registered protocol family 16
[    0.236174] cpuidle: using governor ladder
[    0.252181] cpuidle: using governor menu
[    0.252278] vdso: 2 pages (1 code @ ffffffc000d89000, 1 data @ ffffffc000d88000)
[    0.252295] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.252686] DMA: preallocated 256 KiB pool for atomic allocations
[    0.252741] Serial: AMBA PL011 UART driver
[    0.253975] armada-ap806-pinctrl f06f4000.pinctrl: registered pinctrl driver
[    0.255902] armada-cp110-pinctrl f2440000.pinctrl: registered pinctrl driver
[    0.344317] raid6: int64x1  gen()  1094 MB/s
[    0.412317] raid6: int64x1  xor()   860 MB/s
[    0.480368] raid6: int64x2  gen()  1733 MB/s
[    0.548405] raid6: int64x2  xor()  1303 MB/s
[    0.616443] raid6: int64x4  gen()  2457 MB/s
[    0.684488] raid6: int64x4  xor()  1478 MB/s
[    0.752509] raid6: int64x8  gen()  2519 MB/s
[    0.820562] raid6: int64x8  xor()  1393 MB/s
[    0.888606] raid6: neonx1   gen()  2098 MB/s
[    0.956635] raid6: neonx1   xor()  1349 MB/s
[    1.024683] raid6: neonx2   gen()  3261 MB/s
[    1.092709] raid6: neonx2   xor()  2094 MB/s
[    1.160748] raid6: neonx4   gen()  3986 MB/s
[    1.228795] raid6: neonx4   xor()  2643 MB/s
[    1.296839] raid6: neonx8   gen()  3541 MB/s
[    1.364868] raid6: neonx8   xor()  2650 MB/s
[    1.364870] raid6: using algorithm neonx4 gen() 3986 MB/s
[    1.364873] raid6: .... xor() 2643 MB/s, rmw enabled
[    1.364875] raid6: using intx1 recovery algorithm
[    1.365442] arm-smmu f0100000.iommu: probing hardware configuration...
[    1.365448] arm-smmu f0100000.iommu: SMMUv2 with:
[    1.365452] arm-smmu f0100000.iommu:         stage 1 translation
[    1.365455] arm-smmu f0100000.iommu:         stage 2 translation
[    1.365458] arm-smmu f0100000.iommu:         nested translation
[    1.365462] arm-smmu f0100000.iommu:         coherent table walk
[    1.365466] arm-smmu f0100000.iommu:         stream matching with 16 register groups, mask 0x7fff
[    1.365470] arm-smmu f0100000.iommu:         8 context banks (0 stage-2 only)
[    1.365474] arm-smmu f0100000.iommu:         Supported page sizes: 0x60211000
[    1.365478] arm-smmu f0100000.iommu:         Stage-1: 48-bit VA -> 48-bit IPA
[    1.365481] arm-smmu f0100000.iommu:         Stage-2: 48-bit IPA -> 48-bit PA
[    1.365542] arm-smmu f0100000.iommu: registered 5 master devices
[    1.365940] iommu: Adding device f2500000.usb3 to group 0
[    1.365972] iommu: Adding device f26a0000.dma_xor to group 1
[    1.365985] iommu: Adding device f26c0000.dma_xor to group 2
[    1.366275] vgaarb: loaded
[    1.366403] SCSI subsystem initialized
[    1.366608] usbcore: registered new interface driver usbfs
[    1.366631] usbcore: registered new interface driver hub
[    1.366658] usbcore: registered new device driver usb
[    1.366966] pps_core: LinuxPPS API ver. 1 registered
[    1.366970] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.366982] PTP clock support registered
[    1.367123] dmi: Firmware registration failed.
[    1.367563] Bluetooth: Core ver 2.21
[    1.367582] NET: Registered protocol family 31
[    1.367585] Bluetooth: HCI device and connection manager initialized
[    1.367591] Bluetooth: HCI socket layer initialized
[    1.367595] Bluetooth: L2CAP socket layer initialized
[    1.367606] Bluetooth: SCO socket layer initialized
[    1.369063] clocksource: Switched to clocksource arch_sys_counter
[    1.372302] NET: Registered protocol family 2
[    1.372519] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.372564] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    1.372670] TCP: Hash tables configured (established 16384 bind 16384)
[    1.372725] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    1.372737] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    1.372836] NET: Registered protocol family 1
[    1.377014] RPC: Registered named UNIX socket transport module.
[    1.377019] RPC: Registered udp transport module.
[    1.377021] RPC: Registered tcp transport module.
[    1.377024] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.377344] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    1.377555] kvm [1]: interrupt-controller@f0240000 IRQ9
[    1.377646] kvm [1]: timer IRQ7
[    1.377656] kvm [1]: Hyp mode initialized successfully
[    1.378969] audit: initializing netlink subsys (disabled)
[    1.378990] audit: type=2000 audit(1.376:1): initialized
[    1.379318] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.382679] VFS: Disk quotas dquot_6.6.0
[    1.382758] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.383786] NFS: Registering the id_resolver key type
[    1.383803] Key type id_resolver registered
[    1.383806] Key type id_legacy registered
[    1.383815] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.383942] ntfs: driver 2.1.32 [Flags: R/W].
[    1.384061] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.384302] fuse init (API version 7.23)
[    1.384508] 9p: Installing v9fs 9p2000 file system support
[    1.385934] async_tx: api initialized (async)
[    1.385957] io scheduler noop registered
[    1.386045] io scheduler cfq registered (default)
[    1.386811] irq: Cannot allocate irq_descs @ IRQ109, assuming pre-allocated
[    1.387013] irq: Cannot allocate irq_descs @ IRQ129, assuming pre-allocated
[    1.387175] irq: Cannot allocate irq_descs @ IRQ161, assuming pre-allocated
[    1.387308] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[    1.388228] libphy: Fixed MDIO Bus: probed
[    1.388237] tun: Universal TUN/TAP device driver, 1.6
[    1.388240] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.388335] libphy: mdio_driver_register: mv88e6xxx
[    1.388522] libphy: Marvell XSMI MDIO Bus: probed
[    1.390295] aquantia111c_b0_match_phy_device phydev->c45_ids.device_ids[4]=03a1b7e2h
[    1.390309] aquantia_probe ok
[    1.390415] sky2: driver version 1.30
[    1.390589] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.390593] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.390620] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k
[    1.390622] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.390649] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k
[    1.390652] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.390676] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.2.1-k
[    1.390678] ixgbe: Copyright (c) 1999-2015 Intel Corporation.
[    1.390712] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 2.12.1-k
[    1.390715] ixgbevf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.390738] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[    1.390740] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[    1.390885] usbcore: registered new interface driver asix
[    1.390920] usbcore: registered new interface driver ax88179_178a
[    1.390943] usbcore: registered new interface driver cdc_ether
[    1.390963] usbcore: registered new interface driver net1080
[    1.390983] usbcore: registered new interface driver cdc_subset
[    1.391002] usbcore: registered new interface driver zaurus
[    1.391037] usbcore: registered new interface driver cdc_ncm
[    1.391441] mv_xor_v2 f0400000.dma_xor: Marvell Version 2 XOR driver
[    1.391779] mv_xor_v2 f0420000.dma_xor: Marvell Version 2 XOR driver
[    1.392056] mv_xor_v2 f0440000.dma_xor: Marvell Version 2 XOR driver
[    1.392350] mv_xor_v2 f0460000.dma_xor: Marvell Version 2 XOR driver
[    1.392646] mv_xor_v2 f26a0000.dma_xor: Marvell Version 2 XOR driver
[    1.392701] mv_xor_v2 f26c0000.dma_xor: Marvell Version 2 XOR driver
[    1.394184] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.394834] console [ttyS0] disabled
[    1.414967] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 13, base_baud = 12500000) is a 16550A
[    2.653677] console [ttyS0] enabled
[    2.657964] Unable to detect cache hierarchy for CPU 0
[    2.663507] brd: module loaded
[    2.668684] loop: module loaded
[    2.672268] Warn: ihbbus_guard doesn't exit in dt
[    2.677015] Warn: ihb_cfg_txref_clk doesn't exit in dt
[    2.682198]  device_name (11)
[    2.685182]  sb (4)
[    2.687287]  device_id (4)
[    2.690010]  axi_hb (4)
[    2.692464]  intr_grp (4)
[    2.695101]  node_size (4)
[    2.697824]  remap_size0 (8)
[    2.700714]  remap_size1 (8)
[    2.703609]  txcfg_win_size0 (8)
[    2.706855]  quirks (4)
[    2.709314]  name (10)
[    2.711687] Warn: delayms doesn't exit in dt
[    2.715985] Warn: delayms doesn't exit in dt
[    2.720281] Warn: delayms doesn't exit in dt
[    2.724576] Warn: delayms doesn't exit in dt
[    2.728974] Warn: remap_size0 doesn't exit in dt
[    2.733620]  device_name (13)
[    2.736597]  sb (4)
[    2.738706]  device_id (4)
[    2.741426]  axi_hb (4)
[    2.743879]  intr_grp (4)
[    2.746512]  node_size (4)
[    2.749231]  remap_in_size0 (8)
[    2.752384]  remap_in_size1 (8)
[    2.755539]  remap_out_size0 (8)
[    2.758782]  remap_out_size1 (8)
[    2.762025]  txcfg_win_size0 (8)
[    2.765268]  quirks (4)
[    2.767722]  name (10)
[    2.770097] Warn: delayms doesn't exit in dt
[    2.774391] Warn: delayms doesn't exit in dt
[    2.778684] Warn: delayms doesn't exit in dt
[    2.782976] Warn: delayms doesn't exit in dt
[    2.787983] pxa3xx-nand f2720000.nand: This platform can't do DMA on this device
[    2.795448] pxa3xx-nand f2720000.nand: alloc nand resource failed
[    2.801951] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[    2.806881] 9 ofpart partitions found on MTD device spi0.0
[    2.812394] Creating 9 MTD partitions on "spi0.0":
[    2.817211] 0x000000000000-0x0000001a0000 : "u-boot"
[    2.822592] 0x0000001a0000-0x0000001b0000 : "sharedenv"
[    2.828182] 0x0000001b0000-0x0000001c0000 : "reserved"
[    2.833690] 0x0000001c0000-0x0000001d0000 : "bootinfo"
[    2.839209] 0x0000001d0000-0x0000001e0000 : "mfg_info"
[    2.844703] 0x0000001e0000-0x000000200000 : "cookie"
[    2.850028] 0x000000200000-0x0000003a0000 : "shadow_bootloader"
[    2.856301] 0x0000003b0000-0x0000003f0000 : "firmware"
[    2.861802] 0x0000003f0000-0x000000400000 : "fiq_info"
[    2.867552] VFIO - User Level meta-driver version: 0.3
[    2.873090] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.879654] ehci-pci: EHCI PCI platform driver
[    2.884137] ehci-platform: EHCI generic platform driver
[    2.889447] ehci-orion: EHCI orion driver
[    2.893525] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.899742] ohci-pci: OHCI PCI platform driver
[    2.904232] ohci-platform: OHCI generic platform driver
[    2.909746] usbcore: registered new interface driver usb-storage
[    2.915835] usbcore: registered new interface driver usbserial
[    2.921715] usbcore: registered new interface driver usbserial_generic
[    2.928292] usbserial: USB Serial support registered for generic
[    2.934344] usbcore: registered new interface driver ftdi_sio
[    2.940132] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.947735] mousedev: PS/2 mouse device common for all mice
[    2.953685] armada38x-rtc f2284000.rtc: rtc core: registered f2284000.rtc as rtc0
[    2.961295] i2c /dev entries driver
[    2.985176] armada_thermal f06f808c.thermal: Overheat threshold between 93..106
[    3.002614] armada_thermal f2400078.thermal: Overheat threshold between 92..107
[    3.010126] md: linear personality registered for level -1
[    3.015643] md: raid0 personality registered for level 0
[    3.020984] md: raid1 personality registered for level 1
[    3.026323] md: raid10 personality registered for level 10
[    3.031913] md: raid6 personality registered for level 6
[    3.037253] md: raid5 personality registered for level 5
[    3.042592] md: raid4 personality registered for level 4
[    3.048097] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    3.056627] usbcore: registered new interface driver btusb
[    3.062694] sdhci: Secure Digital Host Controller Interface driver
[    3.068909] sdhci: Copyright(c) Pierre Ossman
[    3.073291] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.079131] ledtrig-cpu: registered to indicate activity on CPUs
[    3.085461] usbcore: registered new interface driver usbhid
[    3.091062] usbhid: USB HID core driver
[    3.095829] coresight-tmc f0809000.etf0: TMC initialized
[    3.101322] coresight-tmc f080a000.etf1: TMC initialized
[    3.106803] coresight-tmc f080b000.etf2: TMC initialized
[    3.112283] coresight-tmc f080c000.etf3: TMC initialized
[    3.117790] coresight-tmc f0811000.etf5: TMC initialized
[    3.123707] coresight-tmc f0812000.etr: TMC initialized
[    3.129133] coresight-funnel f0810000.funnel: FUNNEL initialized
[    3.135488] coresight-etm4x f0c40000.etm0: ETM 4.0 initialized
[    3.141541] coresight-etm4x f0d40000.etm1: ETM 4.0 initialized
[    3.147583] coresight-etm4x f0e40000.etm2: ETM 4.0 initialized
[    3.153626] coresight-etm4x f0f40000.etm3: ETM 4.0 initialized
[    3.159534] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-ddr-rd@840000
[    3.168979] coresight-axim f0840000.axim-ddr-rd: AXIM 4.0 2.0 initialized
[    3.175817] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-ddr-wr@841000
[    3.185255] coresight-axim f0841000.axim-ddr-wr: AXIM 4.0 2.0 initialized
[    3.192092] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-sb-rd@848000
[    3.201441] coresight-axim f0848000.axim-sb-rd: AXIM 4.0 2.0 initialized
[    3.208189] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-sb-wr@849000
[    3.217536] coresight-axim f0849000.axim-sb-wr: AXIM 4.0 2.0 initialized
[    3.224290] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-cp-rd@3c5000
[    3.233470] coresight-axim f23c5000.axim-cp-rd: AXIM 4.0 1.0 initialized
[    3.240219] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-cp-wr@3c6000
[    3.249399] coresight-axim f23c6000.axim-cp-wr: AXIM 4.0 1.0 initialized
[    3.256148] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-ppv2-rd@3c0000
[    3.265502] coresight-axim f23c0000.axim-ppv2-rd: AXIM 4.0 1.0 initialized
[    3.272426] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-ppv2-wr@3c1000
[    3.281778] coresight-axim f23c1000.axim-ppv2-wr: AXIM 4.0 1.0 initialized
[    3.288736] pktgen: Packet Generator for packet performance testing. Version: 2.75
[    3.296875] NET: Registered protocol family 10
[    3.301771] sit: IPv6 over IPv4 tunneling driver
[    3.306676] NET: Registered protocol family 17
[    3.311168] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.324006] Bluetooth: RFCOMM TTY layer initialized
[    3.328915] Bluetooth: RFCOMM socket layer initialized
[    3.334086] Bluetooth: RFCOMM ver 1.11
[    3.337860] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.343201] Bluetooth: BNEP socket layer initialized
[    3.348194] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.354144] Bluetooth: HIDP socket layer initialized
[    3.359156] 8021q: 802.1Q VLAN Support v1.8
[    3.363389] 9pnet: Installing 9P2000 support
[    3.367718] Key type dns_resolver registered
[    3.372011] openvswitch: Open vSwitch switching datapath
[    3.377481] mpls_gso: MPLS GSO support
[    3.381585] registered taskstats version 1
[    3.386677] Btrfs loaded
[    3.389734] mvpp2 f2000000.ppv22: cma_area base 0x000000005c000000 size 256 MB
[    3.403500] gop_mac(0), phy_mode(19)=sfi phy-speed=10000
[    3.408858] mac_addr 0:50:43:0:15:10
[    3.430029] mvpp2 f2000000.ppv22 eth0: Using device tree mac address 00:50:43:00:15:10
[    3.448978] PCI host bridge /cp0/pcie0@600000 ranges:
[    3.454071]    IO 0xf7000000..0xf700ffff -> 0xf7000000
[    3.459244]   MEM 0xc0000000..0xdfffffff -> 0xc0000000
[    4.465063] armada8k-pcie f2600000.pcie0: Link not up after reconfiguration
[    4.472137] armada8k-pcie f2600000.pcie0: PCI host bridge to bus 0000:00
[    4.478874] pci_bus 0000:00: root bus resource [bus 00-ff]
[    4.484391] pci_bus 0000:00: root bus resource [io  0x0000-0xffff] (bus address [0xf7000000-0xf700ffff])
[    4.493916] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff]
[    4.501005] iommu: Adding device 0000:00:00.0 to group 3
[    4.506435] pci 0000:00:00.0: BAR 0: assigned [mem 0xc0000000-0xc00fffff]
[    4.513258] pci 0000:00:00.0: PCI bridge to [bus 01]
[    4.825709] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[    4.832841] mv_xor_v2 f26a0000.dma_xor: Marvell Version 2 XOR driver
[    4.839571] mv_xor_v2 f26c0000.dma_xor: Marvell Version 2 XOR driver
[    4.866633] f2702000.serial: ttyS1 at MMIO 0xf2702000 (irq = 27, base_baud = 15625000) is a 16550A
[    4.896086] f2702100.serial: ttyS2 at MMIO 0xf2702100 (irq = 28, base_baud = 15625000) is a 16550A
[    4.925526] f2702200.serial: ttyS3 at MMIO 0xf2702200 (irq = 29, base_baud = 15625000) is a 16550A
[    4.934693] omap_rng f2760000.trng: Unbalanced pm_runtime_enable!
[    4.940867] omap_rng f2760000.trng: Random Number Generator ver. 203b34c
[    4.948314] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xd3
[    4.954701] nand: Micron MT29F8G08ABACAWP
[    4.958733] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
[    4.966514] pxa3xx-nand f2720000.nand: ECC strength 16, ECC step size 1024
[    4.974276] Bad block table found at page 262080, version 0x01
[    4.981744] Bad block table found at page 262016, version 0x01
[    4.988462] 4 ofpart partitions found on MTD device pxa3xx_nand-0
[    4.994587] Creating 4 MTD partitions on "pxa3xx_nand-0":
[    5.000013] 0x000000000000-0x000000100000 : "DTB"
[    5.005174] 0x000000100000-0x000001300000 : "Linux"
[    5.010412] 0x000001300000-0x00001fd00000 : "Filesystem"
[    5.016123] 0x000020000000-0x00003fd00000 : "Filesystem2"
[    5.022122] xhci-hcd f2500000.usb3: xHCI Host Controller
[    5.027486] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 1
[    5.035194] xhci-hcd f2500000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010090
[    5.043779] xhci-hcd f2500000.usb3: irq 30, io mem 0xf2500000
[    5.049830] hub 1-0:1.0: USB hub found
[    5.053612] hub 1-0:1.0: 1 port detected
[    5.067643] xhci-hcd f2500000.usb3: xHCI Host Controller
[    5.072989] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 2
[    5.080535] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.088892] hub 2-0:1.0: USB hub found
[    5.092672] hub 2-0:1.0: 1 port detected
[    5.097524] ubi0: attaching mtd11
[    5.510071] random: nonblocking pool is initialized
[    8.284742] ubi0: scanning is finished
[    8.299109] ubi0: attached mtd11 (name "Filesystem", size 490 MiB)
[    8.305328] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[    8.312236] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[    8.319058] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[    8.326061] ubi0: good PEBs: 1960, bad PEBs: 0, corrupted PEBs: 0
[    8.332183] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    8.339439] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 716540922
[    8.348528] ubi0: available PEBs: 224, total reserved PEBs: 1736, PEBs reserved for bad PEB handling: 80
[    8.358056] ubi0: background thread "ubi_bgt0d" started, PID 1273
[    8.364181] armada38x-rtc f2284000.rtc: setting system clock to 1970-01-01 00:00:05 UTC (5)
[    8.373500] Waiting 2 sec before mounting root device...
[   10.381079] md: Waiting for all devices to be available before autodetect
[   10.387905] md: If you don't use raid, use raid=noautodetect
[   10.393902] md: Autodetecting RAID arrays.
[   10.398023] md: Scanned 0 and added 0 devices.
[   10.402488] md: autorun ...
[   10.405296] md: ... autorun DONE.
[   10.409633] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1279
[   10.511867] UBIFS (ubi0:0): recovery needed
[   10.716864] UBIFS (ubi0:0): recovery completed
[   10.721371] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[   10.728810] UBIFS (ubi0:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[   10.738771] UBIFS (ubi0:0): FS size: 403783680 bytes (385 MiB, 1590 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs)
[   10.749513] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[   10.755378] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 97DD0887-15F5-4D61-A009-877273AA791A, small LPT model
[   10.768390] VFS: Mounted root (ubifs filesystem) on device 0:15.
[   10.776879] devtmpfs: mounted
[   10.780015] Freeing unused kernel memory: 352K
[   10.784514] Freeing alternatives memory: 72K
Starting logging: OK
Initializing random number generator... done.
Starting system message bus: Could not create /var/lib/dbus/machine-id.YKZAEYEk: No such file or directory
Failed to start message bus: Could not get UID and GID for username "dbus"
done
Starting network...
[   11.691643] ap8x: loading out-of-tree module taints kernel.
[   11.702142] machine is compatible id:0 marvell,armada7040
[   11.707692] resetting mochi interface 0, speed 3
[   11.712344] mci_clrnmask_crc mci_cfg_crc = 38000000
[   11.717253] host mci in reset!
[   11.720325] sb in reset!
[   11.722875] host mci out of reset!
[   11.726293] mci_clrnmask_crc mci_cfg_crc = 38000000
[   11.731208] phy changed speed done!
[   11.787748] IHB 3 link not present, skip traversing
[   11.800665] mci_addr_assign_rec_v18::IHB 3 link not present, skip traversing
[   11.859790]
[   11.859790] IHB::chip count is 2
[   11.864604] *****************************************************
[   11.870726] Mochi Configuration........
[   11.874584] *****************************************************
[   11.880706] -------------CHIP 0-------------
[   11.885000] Chip[0] DEVID=0x0
[   11.887985] Chip[0] DEV_NAME=armada70x0
[   11.891841] Chip[0] CHIPID=0
[   11.894737] Chip[0] MOCHI_REV=0x183
[   11.898249] Chip[0] node_off=0
[   11.901320] Chip[0] EID=0
[   11.903951] Chip[0] Node_CNT=2
[   11.907024] Chip[0] IHB_CNT=1
[   11.910006] Chip[0] Uplink=-1
[   11.912982] Chip[0] Parent Chip_Id=-1
[   11.916663] Chip[0] Parent dwn_hid=-1
[   11.920346] Chip[0] addr_base=0xf9000000
[   11.924289] Chip[0] addr_size=0x0
[   11.927622] Chip[0] LinkSpeed=3
[   11.930780] Chip[0] Pwr_State=0
[   11.933938] Chip[0] Lanes=4
[   11.936742] Chip[0] MCI_CRC_CTRL=38000000 ERR=0
[   11.941295]
[   11.942880] -------------CHIP 1-------------
[   11.947172] Chip[1] DEVID=0x100001f
[   11.950680] Chip[1] DEV_NAME=sc5
[   11.953924] Chip[1] CHIPID=1
[   11.956817] Chip[1] MOCHI_REV=0x184
[   11.960323] Chip[1] node_off=2
[   11.963395] Chip[1] EID=0
[   11.966029] Chip[1] Node_CNT=4
[   11.969100] Chip[1] IHB_CNT=2
[   11.972077] Chip[1] Uplink=2
[   11.974973] Chip[1] Parent Chip_Id=0
[   11.978568] Chip[1] Parent dwn_hid=0
[   11.982161] Chip[1] addr_base=0xf9000000
[   11.986106] Chip[1] addr_size=0x400000
[   11.989875] Chip[1] LinkSpeed=3
[   11.993029] Chip[1] Pwr_State=0
[   11.996187] Chip[1] Lanes=4
[   12.000001] Chip[1] MCI_CRC_CTRL=0 ERR=0
[   12.003944]
[   12.005536] *****************************************************
[   12.012664] IHB 3 link not represent, don't set port state
[   12.419292] sc5/scbt boot ready check timeout
[   12.436782] mci_cfg_crc mci_cfg_crc = a0000
[   12.448110] wlwlan_platform_data_get(), (IoBase0)=(f9000000, f91fffff), more mapping space
[   12.456470] wlwlan_platform_data_get(), (IoBase1)=(f9200000, f92fffff)
[   12.463079] wlwlan_platform_data_get(), carindex:0: ioBaseExt: (v,p)=(ffffff800057e000, fd000000)
[   12.471993] reg(1a800)=1021400h
[   12.475152] ==> This is W9068, rev=2
[   12.478748] Revision: A0
[   12.481295] Running on W9068
[   12.484188] wlprobe  wlpptr->ioBase0 = ffffff8001f80000
[   12.489526] wlprobe  wlpptr->ioBase1 = ffffff8002200000
[   12.494977] wlprobe: intr_shift=0 msix_num=32
[   12.499370] (base, spi)=(f0290040h, c0h)
[   12.503315] => wl_init_intr(),w_reg(ioBase1+30024h) = 38h
[   12.508740] => wl_init_intr(),w_reg(ioBase1+30018h) = 0h
[   12.514079] => wl_init_intr(),w_reg(ioBase1+1a82ch) = 0h
[   12.519417] => wl_init_intr(),w_reg(ioBase1+3002ch) = f0290040h
[   12.525368] => wl_init_intr(),w_reg(ioBase1+30028h) = c0h
[   12.530793] ===> w_reg(ioBase1+30100h) = 0h
[   12.535595] ap8x f9000000.sc5_mci0: hframe base addr 5c3e0000
[   12.541467] ====> Register kdumper successfully
[   12.546811] wlInit SSU pSsuBuf = ffffff8002301000  pPhysSsuBuf = 000000005c400000 size=0x00200000
[   12.555793] wlInit DSP pDspBuf = ffffff80008e7000  pPhysDspBuf = 000000005c3f0000 size=0x00010000
[   12.564707] wlInit wlpptr->pCmdBuf = ffffff80008e2000  wlpptr->wlpd_p->pPhysCmdBuf = 5c0d8000
[   12.573451] The current working directory is /lib/modules/4.4.120/wireless
[   12.580361] fw file: W9068-A0.bin
[   12.583697] read img file: /lib/modules/4.4.120/wireless/W9068-A0.bin...
[   12.783858] FW len = 466972
[   12.787674] fw download start 88
[   12.928850] FwSize = 466972 downloaded Size = 466972 currIteration 65460
[   14.998651] wlFwDownload complete
[   14.998651] FwDownload time = 137924 us
[   14.998651] Radio Cal  time = 2063065 us
[   15.010021] wlQMInit(), Interrupt shift = 0h
[   15.014343] => wlget_extmembuf(), using bootmem_0
[   15.014343] rsvd mem: pbuf=6c000000 vbuf=ffffffc06c000000 size=4000000
[   15.033086] => wlget_extmembuf(), using bootmem_1
[   15.033086] rsvd mem: pbuf=70000000 vbuf=ffffffc070000000 size=6000000
[   15.055580] => wlQMInit(), set qIntOffset = c0h
[   15.074202] => wlInit(), MAC_CONFIG_st->magic = 85h
[   15.079111] => wlInit(), MAC_STATUS_st->verCtrl[3] = f0000000h
[   15.085993] (v,p)=(ffffffc06c000000, 6c000000)
[   15.090460] rxSBinfoBaseAddr_v=ffffffc15c880000, 5c880000, 2048, 128
[   15.096872] Major Version : 1
[   15.099863] Minor Version : 1
[   15.102847] Patch Version : 0
[   15.105832] Num of Regions: 13
[   15.108896] Num of Symbols: 0
[   15.111881] region[ 0].address = 0x    138a40, region[ 0].length = 0x       418
[   15.119225] region[ 1].address = 0x  20123800, region[ 1].length = 0x       800
[   15.126570] region[ 2].address = 0x         0, region[ 2].length = 0x      8000
[   15.133915] region[ 3].address = 0x      8000, region[ 3].length = 0x      8000
[   15.141260] region[ 4].address = 0x    100000, region[ 4].length = 0x     c0000
[   15.148606] region[ 5].address = 0x  20000000, region[ 5].length = 0x    124000
[   15.155953] region[ 6].address = 0x  90040000, region[ 6].length = 0x      8000
[   15.163297] region[ 7].address = 0x  90050000, region[ 7].length = 0x      8000
[   15.170641] region[ 8].address = 0x  90060000, region[ 8].length = 0x      a000
[   15.177986] region[ 9].address = 0x  90070000, region[ 9].length = 0x      a000
[   15.185330] region[10].address = 0x  90080000, region[10].length = 0x      8000
[   15.192674] region[11].address = 0x  90088000, region[11].length = 0x      8000
[   15.200021] region[12].address = 0x  90090000, region[12].length = 0x      b000
[   15.207363] wlFwGetHwSpecs pCmd = ffffff80008e2000
[   15.222271] mac version e0100
[   15.225255] wlpptr->hwData.ulShalVersion:0085
[   15.229637] Mac address = 00:50:43:00:0b:30
[   15.233928] Mac_Init
[   15.239980]   -->num tx desc 2048 num rx desc 16384
[   15.287903] [wlInit_monif] wlinitcnt=0, vmacIndex=32
[   15.293186] wlmon_wdev0 monitor thread created
[   15.297764] resetting mochi interface 1, speed 2
[   15.302413] mci_clrnmask_crc mci_cfg_crc = 38000000
[   15.307589] host mci in reset!
[   15.310677] sb in reset!
[   15.313232] host mci out of reset!
[   15.316647] mci_clrnmask_crc mci_cfg_crc = 38000000
[   15.321562] phy changed speed done!
[   15.412161]
[   15.412161] IHB::chip count is 2
[   15.416975] *****************************************************
[   15.423103] Mochi Configuration........
[   15.426957] *****************************************************
[   15.433079] -------------CHIP 0-------------
[   15.437375] Chip[0] DEVID=0x0
[   15.440353] Chip[0] DEV_NAME=armada70x0_1
[   15.444384] Chip[0] CHIPID=0
[   15.447281] Chip[0] MOCHI_REV=0x183
[   15.450788] Chip[0] node_off=0
[   15.453859] Chip[0] EID=0
[   15.456487] Chip[0] Node_CNT=2
[   15.459557] Chip[0] IHB_CNT=1
[   15.462542] Chip[0] Uplink=-1
[   15.465525] Chip[0] Parent Chip_Id=-1
[   15.469207] Chip[0] Parent dwn_hid=-1
[   15.472881] Chip[0] addr_base=0xf9800000
[   15.476824] Chip[0] addr_size=0x0
[   15.480158] Chip[0] LinkSpeed=2
[   15.483315] Chip[0] Pwr_State=0
[   15.486473] Chip[0] Lanes=2
[   15.489283] Chip[0] MCI_CRC_CTRL=38000000 ERR=0
[   15.493836]
[   15.495418] -------------CHIP 1-------------
[   15.499711] Chip[1] DEVID=0x10021
[   15.503043] Chip[1] DEV_NAME=scbt_a0
[   15.506643] Chip[1] CHIPID=1
[   15.509538] Chip[1] MOCHI_REV=0x184
[   15.513038] Chip[1] node_off=2
[   15.516109] Chip[1] EID=0
[   15.518745] Chip[1] Node_CNT=2
[   15.521814] Chip[1] IHB_CNT=1
[   15.524794] Chip[1] Uplink=2
[   15.527693] Chip[1] Parent Chip_Id=0
[   15.531285] Chip[1] Parent dwn_hid=0
[   15.534878] Chip[1] addr_base=0xf9800000
[   15.538822] Chip[1] addr_size=0x400000
[   15.542589] Chip[1] LinkSpeed=2
[   15.545748] Chip[1] Pwr_State=0
[   15.548900] Chip[1] Lanes=2
[   15.552714] Chip[1] MCI_CRC_CTRL=0 ERR=0
[   15.556654]
[   15.558241] *****************************************************
[   15.565366] IHB 3 link not represent, don't set port state
[   15.574969] mci_cfg_crc mci_cfg_crc = a0000
[   15.580283] wlwlan_platform_data_get(), (IoBase0)=(f9800000, f99fffff), more mapping space
[   15.588636] wlwlan_platform_data_get(), (IoBase1)=(f9a00000, f9afffff)
[   15.595243] wlwlan_platform_data_get(), carindex:1: ioBaseExt: (v,p)=(ffffff800273a000, fe000000)
[   15.604161] reg(1a800)=2021400h
[   15.607324] ==> This is W9064, rev=2
[   15.610917] Revision: A0
[   15.613467] Running on W9064
[   15.616359] wlprobe  wlpptr->ioBase0 = ffffff8002c00000
[   15.621696] wlprobe  wlpptr->ioBase1 = ffffff8002e80000
[   15.627154] wlprobe: intr_shift=0 msix_num=32
[   15.631536] (base, spi)=(f02a0040h, e0h)
[   15.635483] => wl_init_intr(),w_reg(ioBase1+30024h) = 38h
[   15.640910] => wl_init_intr(),w_reg(ioBase1+30018h) = 0h
[   15.646248] => wl_init_intr(),w_reg(ioBase1+1a82ch) = 0h
[   15.651586] => wl_init_intr(),w_reg(ioBase1+3002ch) = f02a0040h
[   15.657536] => wl_init_intr(),w_reg(ioBase1+30028h) = e0h
[   15.662961] ===> w_reg(ioBase1+30100h) = 0h
[   15.667767] ap8x f9800000.sc5_mci1: hframe base addr 5c6e0000
[   15.673640] ====> Register kdumper successfully
[   15.678917] wlInit SSU pSsuBuf = ffffff8002f81000  pPhysSsuBuf = 000000005c900000 size=0x00200000
[   15.687909] wlInit DSP pDspBuf = ffffff8002752000  pPhysDspBuf = 000000005c6f0000 size=0x00010000
[   15.696826] wlInit wlpptr->pCmdBuf = ffffff800274d000  wlpptr->wlpd_p->pPhysCmdBuf = 5c234000
[   15.705466] The current working directory is /lib/modules/4.4.120/wireless
[   15.712383] fw file: W9064-A0.bin
[   15.715720] read img file: /lib/modules/4.4.120/wireless/W9064-A0.bin...
[   15.910572] FW len = 452984
[   15.914390] fw download start 88
[   16.100203] FwSize = 452984 downloaded Size = 452984 currIteration 65480
[   18.155373] wlFwDownload complete
[   18.155373] FwDownload time = 182566 us
[   18.155373] Radio Cal  time = 2048433 us
[   18.166741] wlQMInit(), Interrupt shift = 0h
[   18.171061] => wlget_extmembuf(), using bootmem_2
[   18.171061] rsvd mem: pbuf=76000000 vbuf=ffffffc076000000 size=4000000
[   18.189807] => wlget_extmembuf(), using bootmem_3
[   18.189807] rsvd mem: pbuf=7a000000 vbuf=ffffffc07a000000 size=6000000
[   18.212318] => wlQMInit(), set qIntOffset = e0h
[   18.230981] => wlInit(), MAC_CONFIG_st->magic = 85h
[   18.235901] => wlInit(), MAC_STATUS_st->verCtrl[3] = f0000000h
[   18.242788] (v,p)=(ffffffc076000000, 76000000)
[   18.247255] rxSBinfoBaseAddr_v=ffffffc15cd00000, 5cd00000, 2048, 128
[   18.253670] Major Version : 1
[   18.256648] Minor Version : 1
[   18.259633] Patch Version : 0
[   18.262614] Num of Regions: 13
[   18.265684] Num of Symbols: 0
[   18.268662] region[ 0].address = 0x    135b40, region[ 0].length = 0x       418
[   18.276007] region[ 1].address = 0x  20123800, region[ 1].length = 0x       800
[   18.283352] region[ 2].address = 0x         0, region[ 2].length = 0x      8000
[   18.290696] region[ 3].address = 0x      8000, region[ 3].length = 0x      8000
[   18.298042] region[ 4].address = 0x    100000, region[ 4].length = 0x     c0000
[   18.305385] region[ 5].address = 0x  20000000, region[ 5].length = 0x    124000
[   18.312730] region[ 6].address = 0x  90040000, region[ 6].length = 0x      8000
[   18.320074] region[ 7].address = 0x  90050000, region[ 7].length = 0x      8000
[   18.327417] region[ 8].address = 0x  90060000, region[ 8].length = 0x      a000
[   18.334766] region[ 9].address = 0x  90070000, region[ 9].length = 0x      a000
[   18.342109] region[10].address = 0x  90080000, region[10].length = 0x      8000
[   18.349453] region[11].address = 0x  90088000, region[11].length = 0x      8000
[   18.356795] region[12].address = 0x  90090000, region[12].length = 0x      b000
[   18.364138] wlFwGetHwSpecs pCmd = ffffff800274d000
[   18.379049] mac version e0100
[   18.382033] wlpptr->hwData.ulShalVersion:0085
[   18.386412] Mac address = 00:50:43:00:0b:20
[   18.390703] Mac_Init
[   18.397206]   -->num tx desc 2048 num rx desc 16384
[   18.447032] **Overwrite Clinet macid:31
[   18.451230] [wlInit_monif] wlinitcnt=1, vmacIndex=33
[   18.456481] wlmon_wdev1 monitor thread created
[   18.530965] SET tlv type=14 len=3
[   18.534320] 64 00 00
[   18.537859] SET tlv type=14 len=3
[   18.541207] 65 00 00
[   18.544748] SET tlv type=14 len=3
[   18.548097] 66 00 01
[   18.551657] SET tlv type=14 len=3
[   18.555005] 67 00 01
security open
wdev0     version:

Driver  : 10.14.2.0-W906x       [SHAL 0.85]
Firmware: 1.14.1[   18.571882] br0: port 1(eth0) entered blocking state
.0              [SHAL 0.85][   18.577478] br0: port 1(eth0) entered disabled state

MAC    : 0.14.[   18.583952] device eth0 entered promiscuous mode
1.0             [SHAL 0.85][   18.591126] br0: port 2(wdev0ap0) entered blocking state


wdev1     ve[   18.596620] br0: port 2(wdev0ap0) entered disabled state
rsion:

Driver[   18.603414] device wdev0ap0 entered promiscuous mode
  : 10.14.2.0-W9[   18.610865] br0: port 3(wdev1ap0) entered blocking state
06x     [SHAL 0.85] [   18.616431] br0: port 3(wdev1ap0) entered disabled state

Firmware: 1.14[   18.623254] device wdev1ap0 entered promiscuous mode
.1.0            [SHAL 0.85]
MAC    : 0.14.1.0               [SHAL 0.85]

[   18.646779] mvpp2 f2000000.ppv22 eth0: link up
[   18.654947] 8021q: adding VLAN 0 to HW filter on device eth0
[   18.663116] setting rxantenna 0xf, 0xf
[   18.681100] setting txantenna 0xf, 0xff
[   18.699573] wlInterruptEnable(), w_reg(ffffff80022059c8)=0h
[   18.705177] wlInterruptEnable(), w_reg(ffffff80022059c8)=1ffff00h
[   18.712659] setting rxantenna 0x0, 0xf
[   18.730327] setting txantenna 0x0, 0xf
[   18.748309] wlInterruptEnable(), w_reg(ffffff8002e859c8)=0h
[   18.753913] wlInterruptEnable(), w_reg(ffffff8002e859c8)=1ffff00h
[   18.761470] Build_IE_192 80MHz or less
[   18.765473] WTP_nable=0  macmode=0 tunnel_mode=0 RFID=0 WLANID=0
[   18.772883] Build_IE_192 80MHz or less
[   18.776915] WTP_nable=0  macmode=0 tunnel_mode=0 RFID=1 WLANID=0
[   18.786313] br0: port 3(wdev1ap0) entered blocking state
[   18.791661] br0: port 3(wdev1ap0) entered forwarding state
[   18.797191] br0: port 2(wdev0ap0) entered blocking state
[   18.802532] br0: port 2(wdev0ap0) entered forwarding state
[   18.808056] br0: port 1(eth0) entered blocking state
[   18.813048] br0: port 1(eth0) entered forwarding state
Starting telnetd: OK
Starting WNC rcS...
Starting dhcpd
Starting telnetd
dev:    size   erasesize  name
mtd0: 001a0000 00010000 "u-boot"
mtd1: 00010000 00010000 "sharedenv"
mtd2: 00010000 00010000 "reserved"
mtd3: 00010000 00010000 "bootinfo"
mtd4: 00010000 00010000 "mfg_info"
mtd5: 00020000 00010000 "cookie"
mtd6: 001a0000 00010000 "shadow_bootloader"
mtd7: 00040000 00010000 "firmware"
mtd8: 00010000 00010000 "fiq_info"
mtd9: 00100000 00040000 "DTB"
mtd10: 01200000 00040000 "Linux"
mtd11: 1ea00000 00040000 "Filesystem"
mtd12: 1fd00000 00040000 "Filesystem2"

 WNC Linux Revision: Marvell RXAM-C1.MRVL V1.0.8.2

lrwxrwxrwx    1 ftp      1002            15 Aug 24  2018 /etc/network.sh -> network-5g5g.sh
wdev0     getopmode:48
wdev1     getopmode:48
/ #

BootROM - 2.03 Starting AP IOROM 1.02 Booting from SPI NOR flash 0 Found valid image at boot postion 0x000 lNOTICE: Starting binary extension NOTICE: SVC: SVC is not supported on AP807 NOTICE: Gathering DRAM information mv_ddr: mv_ddr-devel-18.07.0-g2aa16c5-dirty (Aug 24 2018 - 11:16:22) Synopsys DDR43 PHY Firmware version: 0.73a SNPS DDR: 1D training passed SNPS DDR: 2D training passed SNPS DDR: training completed mv_ddr: completed successfully NOTICE: Cold boot NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.4(debug):devel-18.07.2:2aa16c5-dirty NOTICE: BL1: Built : 11:16:24, Aug 24 2018 NOTICE: BL1: Booting BL2 lNOTICE: BL2: v1.4(debug):devel-18.07.2:2aa16c5-dirty NOTICE: BL2: Built : 11:16:26, Aug 24 2018 NOTICE: BL1: Booting BL31 lNOTICE: MSS PM is not supported in this build NOTICE: BL31: v1.4(debug):devel-18.07.2:2aa16c5-dirty NOTICE: BL31: Built : 11:16:29, Aug 24 2018 l U-Boot 2017.03-armada-18.07.1 - WNC RXAM-C1.MRVL V1.0.8.2 (Aug 24 2018 - 11:15:41 +0800) Model: Marvell Armada 3900 AXIS-BT board SoC: Armada3900-A1; AP807-A1; CP115-A0 Clock: CPU 1600 [MHz] DDR 1200 [MHz] FABRIC 1200 [MHz] MSS 200 [MHz] LLC Disabled DRAM: 2 GiB U-Boot DT blob at : 000000007f6eac60 setup_gpio rxam-c1 SGE NAND_USE_FLASH_BBT (in last 8 blocks) Comphy chip #0: Comphy-0: PEX0 5 Gbps Comphy-1: UNCONNECTED Comphy-2: SFI0 10.3125 Gbps Comphy-3: UNCONNECTED Comphy-4: UNCONNECTED Comphy-5: UNCONNECTED UTMI PHY 0 initialized to USB Host0 PCIE-0: Link down NAND: 1024 MiB MMC: Net: eth0: mvpp2-0 [PRIME] XFI: xfi_xsmi_init f2122834=4B78 XFI: xfi_xsmi_init f21228f4=30B4 XSMI: xfi_xsmi_init f212a60c=2E Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x0, size 0x100000 1048576 bytes read: OK NAND read: device 0 offset 0x100000, size 0x1200000 18874368 bytes read: OK ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x1000000 Using Device Tree in place at 0000000001000000, end 000000000100b02f Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 4.4.120-devel-18.07.0 (joseph@d2r120h) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #1 SMP PREEMPT Fri Aug 24 11:13:35 CST 2018 [ 0.000000] Boot CPU: AArch64 Processor [410fd083] [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 256 MiB at 0x000000005c000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] PERCPU: Embedded 16 pages/cpu @ffffffc05bf81000 s24960 r8192 d32384 u65536 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515584 [ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=11,4096 root=ubi0:rootfs rootfstype=ubifs rw chk_data_crc rootdelay=2 [ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes [ 0.000000] log_buf_len min size: 16384 bytes [ 0.000000] log_buf_len: 32768 bytes [ 0.000000] early log buf free: 14744(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] software IO TLB [mem 0x55a00000-0x59a00000] (64MB) mapped at [ffffffc055a00000-ffffffc0599fffff] [ 0.000000] Memory: 1388700K/2095104K available (9608K kernel code, 555K rwdata, 3248K rodata, 352K init, 277K bss, 444260K reserved, 262144K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc0000000 - 0xffffffbdc2000000 ( 32 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB) [ 0.000000] .init : 0xffffffc000d11000 - 0xffffffc000d69000 ( 352 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000d10164 ( 12865 KB) [ 0.000000] .data : 0xffffffc000d82000 - 0xffffffc000e0ce00 ( 556 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GICv2m: Overriding V2M MSI_TYPER (base:160, num:32) [ 0.000000] GICv2m: Node v2m: range[0xf0280000:0xf0280fff], SPI[160:192] [ 0.000000] GICv2m: Overriding V2M MSI_TYPER (base:192, num:32) [ 0.000000] GICv2m: Node v2m: range[0xf0290000:0xf0290fff], SPI[192:224] [ 0.000000] GICv2m: Overriding V2M MSI_TYPER (base:224, num:32) [ 0.000000] GICv2m: Node v2m: range[0xf02a0000:0xf02a0fff], SPI[224:256] [ 0.000000] GICv2m: Overriding V2M MSI_TYPER (base:256, num:32) [ 0.000000] GICv2m: Node v2m: range[0xf02b0000:0xf02b0fff], SPI[256:288] [ 0.000000] mvebu-pic: registered with 19 irqs [ 0.000000] mvebu-sei: registered with 64 irqs [ 0.000000] mvebu-mci-irq: mvebu_mci_of_init total ports 2 registered with 16 irqs [ 0.000000] Architected cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.000106] Console: colour dummy device 80x25 [ 0.000116] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.000122] pid_max: default: 32768 minimum: 301 [ 0.000151] Security Framework initialized [ 0.000170] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000173] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000452] Initializing cgroup subsys memory [ 0.000466] Initializing cgroup subsys hugetlb [ 0.000598] EFI services will not be available. [ 0.000611] ASID allocator initialised with 65536 entries [ 0.036252] Detected PIPT I-cache on CPU1 [ 0.036280] CPU1: Booted secondary processor [410fd083] [ 0.048260] Detected PIPT I-cache on CPU2 [ 0.048282] CPU2: Booted secondary processor [410fd083] [ 0.060271] Detected PIPT I-cache on CPU3 [ 0.060286] CPU3: Booted secondary processor [410fd083] [ 0.060317] Brought up 4 CPUs [ 0.060328] SMP: Total of 4 processors activated. [ 0.060334] CPU: All CPU(s) started at EL2 [ 0.060610] devtmpfs: initialized [ 0.063503] DMI not present or invalid. [ 0.063632] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.063645] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.066723] xor: measuring software checksum speed [ 0.104081] 8regs : 6412.000 MB/sec [ 0.144103] 8regs_prefetch: 5620.000 MB/sec [ 0.184126] 32regs : 7542.000 MB/sec [ 0.224150] 32regs_prefetch: 6304.000 MB/sec [ 0.224153] xor: using function: 32regs (7542.000 MB/sec) [ 0.224162] pinctrl core: initialized pinctrl subsystem [ 0.224698] NET: Registered protocol family 16 [ 0.236174] cpuidle: using governor ladder [ 0.252181] cpuidle: using governor menu [ 0.252278] vdso: 2 pages (1 code @ ffffffc000d89000, 1 data @ ffffffc000d88000) [ 0.252295] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.252686] DMA: preallocated 256 KiB pool for atomic allocations [ 0.252741] Serial: AMBA PL011 UART driver [ 0.253975] armada-ap806-pinctrl f06f4000.pinctrl: registered pinctrl driver [ 0.255902] armada-cp110-pinctrl f2440000.pinctrl: registered pinctrl driver [ 0.344317] raid6: int64x1 gen() 1094 MB/s [ 0.412317] raid6: int64x1 xor() 860 MB/s [ 0.480368] raid6: int64x2 gen() 1733 MB/s [ 0.548405] raid6: int64x2 xor() 1303 MB/s [ 0.616443] raid6: int64x4 gen() 2457 MB/s [ 0.684488] raid6: int64x4 xor() 1478 MB/s [ 0.752509] raid6: int64x8 gen() 2519 MB/s [ 0.820562] raid6: int64x8 xor() 1393 MB/s [ 0.888606] raid6: neonx1 gen() 2098 MB/s [ 0.956635] raid6: neonx1 xor() 1349 MB/s [ 1.024683] raid6: neonx2 gen() 3261 MB/s [ 1.092709] raid6: neonx2 xor() 2094 MB/s [ 1.160748] raid6: neonx4 gen() 3986 MB/s [ 1.228795] raid6: neonx4 xor() 2643 MB/s [ 1.296839] raid6: neonx8 gen() 3541 MB/s [ 1.364868] raid6: neonx8 xor() 2650 MB/s [ 1.364870] raid6: using algorithm neonx4 gen() 3986 MB/s [ 1.364873] raid6: .... xor() 2643 MB/s, rmw enabled [ 1.364875] raid6: using intx1 recovery algorithm [ 1.365442] arm-smmu f0100000.iommu: probing hardware configuration... [ 1.365448] arm-smmu f0100000.iommu: SMMUv2 with: [ 1.365452] arm-smmu f0100000.iommu: stage 1 translation [ 1.365455] arm-smmu f0100000.iommu: stage 2 translation [ 1.365458] arm-smmu f0100000.iommu: nested translation [ 1.365462] arm-smmu f0100000.iommu: coherent table walk [ 1.365466] arm-smmu f0100000.iommu: stream matching with 16 register groups, mask 0x7fff [ 1.365470] arm-smmu f0100000.iommu: 8 context banks (0 stage-2 only) [ 1.365474] arm-smmu f0100000.iommu: Supported page sizes: 0x60211000 [ 1.365478] arm-smmu f0100000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.365481] arm-smmu f0100000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.365542] arm-smmu f0100000.iommu: registered 5 master devices [ 1.365940] iommu: Adding device f2500000.usb3 to group 0 [ 1.365972] iommu: Adding device f26a0000.dma_xor to group 1 [ 1.365985] iommu: Adding device f26c0000.dma_xor to group 2 [ 1.366275] vgaarb: loaded [ 1.366403] SCSI subsystem initialized [ 1.366608] usbcore: registered new interface driver usbfs [ 1.366631] usbcore: registered new interface driver hub [ 1.366658] usbcore: registered new device driver usb [ 1.366966] pps_core: LinuxPPS API ver. 1 registered [ 1.366970] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.366982] PTP clock support registered [ 1.367123] dmi: Firmware registration failed. [ 1.367563] Bluetooth: Core ver 2.21 [ 1.367582] NET: Registered protocol family 31 [ 1.367585] Bluetooth: HCI device and connection manager initialized [ 1.367591] Bluetooth: HCI socket layer initialized [ 1.367595] Bluetooth: L2CAP socket layer initialized [ 1.367606] Bluetooth: SCO socket layer initialized [ 1.369063] clocksource: Switched to clocksource arch_sys_counter [ 1.372302] NET: Registered protocol family 2 [ 1.372519] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 1.372564] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 1.372670] TCP: Hash tables configured (established 16384 bind 16384) [ 1.372725] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 1.372737] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 1.372836] NET: Registered protocol family 1 [ 1.377014] RPC: Registered named UNIX socket transport module. [ 1.377019] RPC: Registered udp transport module. [ 1.377021] RPC: Registered tcp transport module. [ 1.377024] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.377344] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available [ 1.377555] kvm [1]: interrupt-controller@f0240000 IRQ9 [ 1.377646] kvm [1]: timer IRQ7 [ 1.377656] kvm [1]: Hyp mode initialized successfully [ 1.378969] audit: initializing netlink subsys (disabled) [ 1.378990] audit: type=2000 audit(1.376:1): initialized [ 1.379318] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.382679] VFS: Disk quotas dquot_6.6.0 [ 1.382758] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.383786] NFS: Registering the id_resolver key type [ 1.383803] Key type id_resolver registered [ 1.383806] Key type id_legacy registered [ 1.383815] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.383942] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.384061] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 1.384302] fuse init (API version 7.23) [ 1.384508] 9p: Installing v9fs 9p2000 file system support [ 1.385934] async_tx: api initialized (async) [ 1.385957] io scheduler noop registered [ 1.386045] io scheduler cfq registered (default) [ 1.386811] irq: Cannot allocate irq_descs @ IRQ109, assuming pre-allocated [ 1.387013] irq: Cannot allocate irq_descs @ IRQ129, assuming pre-allocated [ 1.387175] irq: Cannot allocate irq_descs @ IRQ161, assuming pre-allocated [ 1.387308] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 1.388228] libphy: Fixed MDIO Bus: probed [ 1.388237] tun: Universal TUN/TAP device driver, 1.6 [ 1.388240] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.388335] libphy: mdio_driver_register: mv88e6xxx [ 1.388522] libphy: Marvell XSMI MDIO Bus: probed [ 1.390295] aquantia111c_b0_match_phy_device phydev->c45_ids.device_ids[4]=03a1b7e2h [ 1.390309] aquantia_probe ok [ 1.390415] sky2: driver version 1.30 [ 1.390589] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.390593] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.390620] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k [ 1.390622] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.390649] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k [ 1.390652] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.390676] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.2.1-k [ 1.390678] ixgbe: Copyright (c) 1999-2015 Intel Corporation. [ 1.390712] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 2.12.1-k [ 1.390715] ixgbevf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.390738] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 1.390740] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 1.390885] usbcore: registered new interface driver asix [ 1.390920] usbcore: registered new interface driver ax88179_178a [ 1.390943] usbcore: registered new interface driver cdc_ether [ 1.390963] usbcore: registered new interface driver net1080 [ 1.390983] usbcore: registered new interface driver cdc_subset [ 1.391002] usbcore: registered new interface driver zaurus [ 1.391037] usbcore: registered new interface driver cdc_ncm [ 1.391441] mv_xor_v2 f0400000.dma_xor: Marvell Version 2 XOR driver [ 1.391779] mv_xor_v2 f0420000.dma_xor: Marvell Version 2 XOR driver [ 1.392056] mv_xor_v2 f0440000.dma_xor: Marvell Version 2 XOR driver [ 1.392350] mv_xor_v2 f0460000.dma_xor: Marvell Version 2 XOR driver [ 1.392646] mv_xor_v2 f26a0000.dma_xor: Marvell Version 2 XOR driver [ 1.392701] mv_xor_v2 f26c0000.dma_xor: Marvell Version 2 XOR driver [ 1.394184] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.394834] console [ttyS0] disabled [ 1.414967] f0512000.serial: ttyS0 at MMIO 0xf0512000 (irq = 13, base_baud = 12500000) is a 16550A [ 2.653677] console [ttyS0] enabled [ 2.657964] Unable to detect cache hierarchy for CPU 0 [ 2.663507] brd: module loaded [ 2.668684] loop: module loaded [ 2.672268] Warn: ihbbus_guard doesn't exit in dt [ 2.677015] Warn: ihb_cfg_txref_clk doesn't exit in dt [ 2.682198] device_name (11) [ 2.685182] sb (4) [ 2.687287] device_id (4) [ 2.690010] axi_hb (4) [ 2.692464] intr_grp (4) [ 2.695101] node_size (4) [ 2.697824] remap_size0 (8) [ 2.700714] remap_size1 (8) [ 2.703609] txcfg_win_size0 (8) [ 2.706855] quirks (4) [ 2.709314] name (10) [ 2.711687] Warn: delayms doesn't exit in dt [ 2.715985] Warn: delayms doesn't exit in dt [ 2.720281] Warn: delayms doesn't exit in dt [ 2.724576] Warn: delayms doesn't exit in dt [ 2.728974] Warn: remap_size0 doesn't exit in dt [ 2.733620] device_name (13) [ 2.736597] sb (4) [ 2.738706] device_id (4) [ 2.741426] axi_hb (4) [ 2.743879] intr_grp (4) [ 2.746512] node_size (4) [ 2.749231] remap_in_size0 (8) [ 2.752384] remap_in_size1 (8) [ 2.755539] remap_out_size0 (8) [ 2.758782] remap_out_size1 (8) [ 2.762025] txcfg_win_size0 (8) [ 2.765268] quirks (4) [ 2.767722] name (10) [ 2.770097] Warn: delayms doesn't exit in dt [ 2.774391] Warn: delayms doesn't exit in dt [ 2.778684] Warn: delayms doesn't exit in dt [ 2.782976] Warn: delayms doesn't exit in dt [ 2.787983] pxa3xx-nand f2720000.nand: This platform can't do DMA on this device [ 2.795448] pxa3xx-nand f2720000.nand: alloc nand resource failed [ 2.801951] m25p80 spi0.0: mx25l3205d (4096 Kbytes) [ 2.806881] 9 ofpart partitions found on MTD device spi0.0 [ 2.812394] Creating 9 MTD partitions on "spi0.0": [ 2.817211] 0x000000000000-0x0000001a0000 : "u-boot" [ 2.822592] 0x0000001a0000-0x0000001b0000 : "sharedenv" [ 2.828182] 0x0000001b0000-0x0000001c0000 : "reserved" [ 2.833690] 0x0000001c0000-0x0000001d0000 : "bootinfo" [ 2.839209] 0x0000001d0000-0x0000001e0000 : "mfg_info" [ 2.844703] 0x0000001e0000-0x000000200000 : "cookie" [ 2.850028] 0x000000200000-0x0000003a0000 : "shadow_bootloader" [ 2.856301] 0x0000003b0000-0x0000003f0000 : "firmware" [ 2.861802] 0x0000003f0000-0x000000400000 : "fiq_info" [ 2.867552] VFIO - User Level meta-driver version: 0.3 [ 2.873090] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.879654] ehci-pci: EHCI PCI platform driver [ 2.884137] ehci-platform: EHCI generic platform driver [ 2.889447] ehci-orion: EHCI orion driver [ 2.893525] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.899742] ohci-pci: OHCI PCI platform driver [ 2.904232] ohci-platform: OHCI generic platform driver [ 2.909746] usbcore: registered new interface driver usb-storage [ 2.915835] usbcore: registered new interface driver usbserial [ 2.921715] usbcore: registered new interface driver usbserial_generic [ 2.928292] usbserial: USB Serial support registered for generic [ 2.934344] usbcore: registered new interface driver ftdi_sio [ 2.940132] usbserial: USB Serial support registered for FTDI USB Serial Device [ 2.947735] mousedev: PS/2 mouse device common for all mice [ 2.953685] armada38x-rtc f2284000.rtc: rtc core: registered f2284000.rtc as rtc0 [ 2.961295] i2c /dev entries driver [ 2.985176] armada_thermal f06f808c.thermal: Overheat threshold between 93..106 [ 3.002614] armada_thermal f2400078.thermal: Overheat threshold between 92..107 [ 3.010126] md: linear personality registered for level -1 [ 3.015643] md: raid0 personality registered for level 0 [ 3.020984] md: raid1 personality registered for level 1 [ 3.026323] md: raid10 personality registered for level 10 [ 3.031913] md: raid6 personality registered for level 6 [ 3.037253] md: raid5 personality registered for level 5 [ 3.042592] md: raid4 personality registered for level 4 [ 3.048097] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 3.056627] usbcore: registered new interface driver btusb [ 3.062694] sdhci: Secure Digital Host Controller Interface driver [ 3.068909] sdhci: Copyright(c) Pierre Ossman [ 3.073291] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.079131] ledtrig-cpu: registered to indicate activity on CPUs [ 3.085461] usbcore: registered new interface driver usbhid [ 3.091062] usbhid: USB HID core driver [ 3.095829] coresight-tmc f0809000.etf0: TMC initialized [ 3.101322] coresight-tmc f080a000.etf1: TMC initialized [ 3.106803] coresight-tmc f080b000.etf2: TMC initialized [ 3.112283] coresight-tmc f080c000.etf3: TMC initialized [ 3.117790] coresight-tmc f0811000.etf5: TMC initialized [ 3.123707] coresight-tmc f0812000.etr: TMC initialized [ 3.129133] coresight-funnel f0810000.funnel: FUNNEL initialized [ 3.135488] coresight-etm4x f0c40000.etm0: ETM 4.0 initialized [ 3.141541] coresight-etm4x f0d40000.etm1: ETM 4.0 initialized [ 3.147583] coresight-etm4x f0e40000.etm2: ETM 4.0 initialized [ 3.153626] coresight-etm4x f0f40000.etm3: ETM 4.0 initialized [ 3.159534] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-ddr-rd@840000 [ 3.168979] coresight-axim f0840000.axim-ddr-rd: AXIM 4.0 2.0 initialized [ 3.175817] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-ddr-wr@841000 [ 3.185255] coresight-axim f0841000.axim-ddr-wr: AXIM 4.0 2.0 initialized [ 3.192092] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-sb-rd@848000 [ 3.201441] coresight-axim f0848000.axim-sb-rd: AXIM 4.0 2.0 initialized [ 3.208189] of_graph_get_next_endpoint(): no port node found in /ap806/config-space/axim-sb-wr@849000 [ 3.217536] coresight-axim f0849000.axim-sb-wr: AXIM 4.0 2.0 initialized [ 3.224290] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-cp-rd@3c5000 [ 3.233470] coresight-axim f23c5000.axim-cp-rd: AXIM 4.0 1.0 initialized [ 3.240219] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-cp-wr@3c6000 [ 3.249399] coresight-axim f23c6000.axim-cp-wr: AXIM 4.0 1.0 initialized [ 3.256148] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-ppv2-rd@3c0000 [ 3.265502] coresight-axim f23c0000.axim-ppv2-rd: AXIM 4.0 1.0 initialized [ 3.272426] of_graph_get_next_endpoint(): no port node found in /cp0/config-space/axim-ppv2-wr@3c1000 [ 3.281778] coresight-axim f23c1000.axim-ppv2-wr: AXIM 4.0 1.0 initialized [ 3.288736] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 3.296875] NET: Registered protocol family 10 [ 3.301771] sit: IPv6 over IPv4 tunneling driver [ 3.306676] NET: Registered protocol family 17 [ 3.311168] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.324006] Bluetooth: RFCOMM TTY layer initialized [ 3.328915] Bluetooth: RFCOMM socket layer initialized [ 3.334086] Bluetooth: RFCOMM ver 1.11 [ 3.337860] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.343201] Bluetooth: BNEP socket layer initialized [ 3.348194] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 3.354144] Bluetooth: HIDP socket layer initialized [ 3.359156] 8021q: 802.1Q VLAN Support v1.8 [ 3.363389] 9pnet: Installing 9P2000 support [ 3.367718] Key type dns_resolver registered [ 3.372011] openvswitch: Open vSwitch switching datapath [ 3.377481] mpls_gso: MPLS GSO support [ 3.381585] registered taskstats version 1 [ 3.386677] Btrfs loaded [ 3.389734] mvpp2 f2000000.ppv22: cma_area base 0x000000005c000000 size 256 MB [ 3.403500] gop_mac(0), phy_mode(19)=sfi phy-speed=10000 [ 3.408858] mac_addr 0:50:43:0:15:10 [ 3.430029] mvpp2 f2000000.ppv22 eth0: Using device tree mac address 00:50:43:00:15:10 [ 3.448978] PCI host bridge /cp0/pcie0@600000 ranges: [ 3.454071] IO 0xf7000000..0xf700ffff -> 0xf7000000 [ 3.459244] MEM 0xc0000000..0xdfffffff -> 0xc0000000 [ 4.465063] armada8k-pcie f2600000.pcie0: Link not up after reconfiguration [ 4.472137] armada8k-pcie f2600000.pcie0: PCI host bridge to bus 0000:00 [ 4.478874] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.484391] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0xf7000000-0xf700ffff]) [ 4.493916] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff] [ 4.501005] iommu: Adding device 0000:00:00.0 to group 3 [ 4.506435] pci 0000:00:00.0: BAR 0: assigned [mem 0xc0000000-0xc00fffff] [ 4.513258] pci 0000:00:00.0: PCI bridge to [bus 01] [ 4.825709] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 4.832841] mv_xor_v2 f26a0000.dma_xor: Marvell Version 2 XOR driver [ 4.839571] mv_xor_v2 f26c0000.dma_xor: Marvell Version 2 XOR driver [ 4.866633] f2702000.serial: ttyS1 at MMIO 0xf2702000 (irq = 27, base_baud = 15625000) is a 16550A [ 4.896086] f2702100.serial: ttyS2 at MMIO 0xf2702100 (irq = 28, base_baud = 15625000) is a 16550A [ 4.925526] f2702200.serial: ttyS3 at MMIO 0xf2702200 (irq = 29, base_baud = 15625000) is a 16550A [ 4.934693] omap_rng f2760000.trng: Unbalanced pm_runtime_enable! [ 4.940867] omap_rng f2760000.trng: Random Number Generator ver. 203b34c [ 4.948314] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xd3 [ 4.954701] nand: Micron MT29F8G08ABACAWP [ 4.958733] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 [ 4.966514] pxa3xx-nand f2720000.nand: ECC strength 16, ECC step size 1024 [ 4.974276] Bad block table found at page 262080, version 0x01 [ 4.981744] Bad block table found at page 262016, version 0x01 [ 4.988462] 4 ofpart partitions found on MTD device pxa3xx_nand-0 [ 4.994587] Creating 4 MTD partitions on "pxa3xx_nand-0": [ 5.000013] 0x000000000000-0x000000100000 : "DTB" [ 5.005174] 0x000000100000-0x000001300000 : "Linux" [ 5.010412] 0x000001300000-0x00001fd00000 : "Filesystem" [ 5.016123] 0x000020000000-0x00003fd00000 : "Filesystem2" [ 5.022122] xhci-hcd f2500000.usb3: xHCI Host Controller [ 5.027486] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 1 [ 5.035194] xhci-hcd f2500000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010090 [ 5.043779] xhci-hcd f2500000.usb3: irq 30, io mem 0xf2500000 [ 5.049830] hub 1-0:1.0: USB hub found [ 5.053612] hub 1-0:1.0: 1 port detected [ 5.067643] xhci-hcd f2500000.usb3: xHCI Host Controller [ 5.072989] xhci-hcd f2500000.usb3: new USB bus registered, assigned bus number 2 [ 5.080535] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.088892] hub 2-0:1.0: USB hub found [ 5.092672] hub 2-0:1.0: 1 port detected [ 5.097524] ubi0: attaching mtd11 [ 5.510071] random: nonblocking pool is initialized [ 8.284742] ubi0: scanning is finished [ 8.299109] ubi0: attached mtd11 (name "Filesystem", size 490 MiB) [ 8.305328] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes [ 8.312236] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 8.319058] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 8.326061] ubi0: good PEBs: 1960, bad PEBs: 0, corrupted PEBs: 0 [ 8.332183] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 8.339439] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 716540922 [ 8.348528] ubi0: available PEBs: 224, total reserved PEBs: 1736, PEBs reserved for bad PEB handling: 80 [ 8.358056] ubi0: background thread "ubi_bgt0d" started, PID 1273 [ 8.364181] armada38x-rtc f2284000.rtc: setting system clock to 1970-01-01 00:00:05 UTC (5) [ 8.373500] Waiting 2 sec before mounting root device... [ 10.381079] md: Waiting for all devices to be available before autodetect [ 10.387905] md: If you don't use raid, use raid=noautodetect [ 10.393902] md: Autodetecting RAID arrays. [ 10.398023] md: Scanned 0 and added 0 devices. [ 10.402488] md: autorun ... [ 10.405296] md: ... autorun DONE. [ 10.409633] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1279 [ 10.511867] UBIFS (ubi0:0): recovery needed [ 10.716864] UBIFS (ubi0:0): recovery completed [ 10.721371] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 10.728810] UBIFS (ubi0:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 10.738771] UBIFS (ubi0:0): FS size: 403783680 bytes (385 MiB, 1590 LEBs), journal size 9404416 bytes (8 MiB, 38 LEBs) [ 10.749513] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) [ 10.755378] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 97DD0887-15F5-4D61-A009-877273AA791A, small LPT model [ 10.768390] VFS: Mounted root (ubifs filesystem) on device 0:15. [ 10.776879] devtmpfs: mounted [ 10.780015] Freeing unused kernel memory: 352K [ 10.784514] Freeing alternatives memory: 72K Starting logging: OK Initializing random number generator... done. Starting system message bus: Could not create /var/lib/dbus/machine-id.YKZAEYEk: No such file or directory Failed to start message bus: Could not get UID and GID for username "dbus" done Starting network... [ 11.691643] ap8x: loading out-of-tree module taints kernel. [ 11.702142] machine is compatible id:0 marvell,armada7040 [ 11.707692] resetting mochi interface 0, speed 3 [ 11.712344] mci_clrnmask_crc mci_cfg_crc = 38000000 [ 11.717253] host mci in reset! [ 11.720325] sb in reset! [ 11.722875] host mci out of reset! [ 11.726293] mci_clrnmask_crc mci_cfg_crc = 38000000 [ 11.731208] phy changed speed done! [ 11.787748] IHB 3 link not present, skip traversing [ 11.800665] mci_addr_assign_rec_v18::IHB 3 link not present, skip traversing [ 11.859790] [ 11.859790] IHB::chip count is 2 [ 11.864604] ***************************************************** [ 11.870726] Mochi Configuration........ [ 11.874584] ***************************************************** [ 11.880706] -------------CHIP 0------------- [ 11.885000] Chip[0] DEVID=0x0 [ 11.887985] Chip[0] DEV_NAME=armada70x0 [ 11.891841] Chip[0] CHIPID=0 [ 11.894737] Chip[0] MOCHI_REV=0x183 [ 11.898249] Chip[0] node_off=0 [ 11.901320] Chip[0] EID=0 [ 11.903951] Chip[0] Node_CNT=2 [ 11.907024] Chip[0] IHB_CNT=1 [ 11.910006] Chip[0] Uplink=-1 [ 11.912982] Chip[0] Parent Chip_Id=-1 [ 11.916663] Chip[0] Parent dwn_hid=-1 [ 11.920346] Chip[0] addr_base=0xf9000000 [ 11.924289] Chip[0] addr_size=0x0 [ 11.927622] Chip[0] LinkSpeed=3 [ 11.930780] Chip[0] Pwr_State=0 [ 11.933938] Chip[0] Lanes=4 [ 11.936742] Chip[0] MCI_CRC_CTRL=38000000 ERR=0 [ 11.941295] [ 11.942880] -------------CHIP 1------------- [ 11.947172] Chip[1] DEVID=0x100001f [ 11.950680] Chip[1] DEV_NAME=sc5 [ 11.953924] Chip[1] CHIPID=1 [ 11.956817] Chip[1] MOCHI_REV=0x184 [ 11.960323] Chip[1] node_off=2 [ 11.963395] Chip[1] EID=0 [ 11.966029] Chip[1] Node_CNT=4 [ 11.969100] Chip[1] IHB_CNT=2 [ 11.972077] Chip[1] Uplink=2 [ 11.974973] Chip[1] Parent Chip_Id=0 [ 11.978568] Chip[1] Parent dwn_hid=0 [ 11.982161] Chip[1] addr_base=0xf9000000 [ 11.986106] Chip[1] addr_size=0x400000 [ 11.989875] Chip[1] LinkSpeed=3 [ 11.993029] Chip[1] Pwr_State=0 [ 11.996187] Chip[1] Lanes=4 [ 12.000001] Chip[1] MCI_CRC_CTRL=0 ERR=0 [ 12.003944] [ 12.005536] ***************************************************** [ 12.012664] IHB 3 link not represent, don't set port state [ 12.419292] sc5/scbt boot ready check timeout [ 12.436782] mci_cfg_crc mci_cfg_crc = a0000 [ 12.448110] wlwlan_platform_data_get(), (IoBase0)=(f9000000, f91fffff), more mapping space [ 12.456470] wlwlan_platform_data_get(), (IoBase1)=(f9200000, f92fffff) [ 12.463079] wlwlan_platform_data_get(), carindex:0: ioBaseExt: (v,p)=(ffffff800057e000, fd000000) [ 12.471993] reg(1a800)=1021400h [ 12.475152] ==> This is W9068, rev=2 [ 12.478748] Revision: A0 [ 12.481295] Running on W9068 [ 12.484188] wlprobe wlpptr->ioBase0 = ffffff8001f80000 [ 12.489526] wlprobe wlpptr->ioBase1 = ffffff8002200000 [ 12.494977] wlprobe: intr_shift=0 msix_num=32 [ 12.499370] (base, spi)=(f0290040h, c0h) [ 12.503315] => wl_init_intr(),w_reg(ioBase1+30024h) = 38h [ 12.508740] => wl_init_intr(),w_reg(ioBase1+30018h) = 0h [ 12.514079] => wl_init_intr(),w_reg(ioBase1+1a82ch) = 0h [ 12.519417] => wl_init_intr(),w_reg(ioBase1+3002ch) = f0290040h [ 12.525368] => wl_init_intr(),w_reg(ioBase1+30028h) = c0h [ 12.530793] ===> w_reg(ioBase1+30100h) = 0h [ 12.535595] ap8x f9000000.sc5_mci0: hframe base addr 5c3e0000 [ 12.541467] ====> Register kdumper successfully [ 12.546811] wlInit SSU pSsuBuf = ffffff8002301000 pPhysSsuBuf = 000000005c400000 size=0x00200000 [ 12.555793] wlInit DSP pDspBuf = ffffff80008e7000 pPhysDspBuf = 000000005c3f0000 size=0x00010000 [ 12.564707] wlInit wlpptr->pCmdBuf = ffffff80008e2000 wlpptr->wlpd_p->pPhysCmdBuf = 5c0d8000 [ 12.573451] The current working directory is /lib/modules/4.4.120/wireless [ 12.580361] fw file: W9068-A0.bin [ 12.583697] read img file: /lib/modules/4.4.120/wireless/W9068-A0.bin... [ 12.783858] FW len = 466972 [ 12.787674] fw download start 88 [ 12.928850] FwSize = 466972 downloaded Size = 466972 currIteration 65460 [ 14.998651] wlFwDownload complete [ 14.998651] FwDownload time = 137924 us [ 14.998651] Radio Cal time = 2063065 us [ 15.010021] wlQMInit(), Interrupt shift = 0h [ 15.014343] => wlget_extmembuf(), using bootmem_0 [ 15.014343] rsvd mem: pbuf=6c000000 vbuf=ffffffc06c000000 size=4000000 [ 15.033086] => wlget_extmembuf(), using bootmem_1 [ 15.033086] rsvd mem: pbuf=70000000 vbuf=ffffffc070000000 size=6000000 [ 15.055580] => wlQMInit(), set qIntOffset = c0h [ 15.074202] => wlInit(), MAC_CONFIG_st->magic = 85h [ 15.079111] => wlInit(), MAC_STATUS_st->verCtrl[3] = f0000000h [ 15.085993] (v,p)=(ffffffc06c000000, 6c000000) [ 15.090460] rxSBinfoBaseAddr_v=ffffffc15c880000, 5c880000, 2048, 128 [ 15.096872] Major Version : 1 [ 15.099863] Minor Version : 1 [ 15.102847] Patch Version : 0 [ 15.105832] Num of Regions: 13 [ 15.108896] Num of Symbols: 0 [ 15.111881] region[ 0].address = 0x 138a40, region[ 0].length = 0x 418 [ 15.119225] region[ 1].address = 0x 20123800, region[ 1].length = 0x 800 [ 15.126570] region[ 2].address = 0x 0, region[ 2].length = 0x 8000 [ 15.133915] region[ 3].address = 0x 8000, region[ 3].length = 0x 8000 [ 15.141260] region[ 4].address = 0x 100000, region[ 4].length = 0x c0000 [ 15.148606] region[ 5].address = 0x 20000000, region[ 5].length = 0x 124000 [ 15.155953] region[ 6].address = 0x 90040000, region[ 6].length = 0x 8000 [ 15.163297] region[ 7].address = 0x 90050000, region[ 7].length = 0x 8000 [ 15.170641] region[ 8].address = 0x 90060000, region[ 8].length = 0x a000 [ 15.177986] region[ 9].address = 0x 90070000, region[ 9].length = 0x a000 [ 15.185330] region[10].address = 0x 90080000, region[10].length = 0x 8000 [ 15.192674] region[11].address = 0x 90088000, region[11].length = 0x 8000 [ 15.200021] region[12].address = 0x 90090000, region[12].length = 0x b000 [ 15.207363] wlFwGetHwSpecs pCmd = ffffff80008e2000 [ 15.222271] mac version e0100 [ 15.225255] wlpptr->hwData.ulShalVersion:0085 [ 15.229637] Mac address = 00:50:43:00:0b:30 [ 15.233928] Mac_Init [ 15.239980] -->num tx desc 2048 num rx desc 16384 [ 15.287903] [wlInit_monif] wlinitcnt=0, vmacIndex=32 [ 15.293186] wlmon_wdev0 monitor thread created [ 15.297764] resetting mochi interface 1, speed 2 [ 15.302413] mci_clrnmask_crc mci_cfg_crc = 38000000 [ 15.307589] host mci in reset! [ 15.310677] sb in reset! [ 15.313232] host mci out of reset! [ 15.316647] mci_clrnmask_crc mci_cfg_crc = 38000000 [ 15.321562] phy changed speed done! [ 15.412161] [ 15.412161] IHB::chip count is 2 [ 15.416975] ***************************************************** [ 15.423103] Mochi Configuration........ [ 15.426957] ***************************************************** [ 15.433079] -------------CHIP 0------------- [ 15.437375] Chip[0] DEVID=0x0 [ 15.440353] Chip[0] DEV_NAME=armada70x0_1 [ 15.444384] Chip[0] CHIPID=0 [ 15.447281] Chip[0] MOCHI_REV=0x183 [ 15.450788] Chip[0] node_off=0 [ 15.453859] Chip[0] EID=0 [ 15.456487] Chip[0] Node_CNT=2 [ 15.459557] Chip[0] IHB_CNT=1 [ 15.462542] Chip[0] Uplink=-1 [ 15.465525] Chip[0] Parent Chip_Id=-1 [ 15.469207] Chip[0] Parent dwn_hid=-1 [ 15.472881] Chip[0] addr_base=0xf9800000 [ 15.476824] Chip[0] addr_size=0x0 [ 15.480158] Chip[0] LinkSpeed=2 [ 15.483315] Chip[0] Pwr_State=0 [ 15.486473] Chip[0] Lanes=2 [ 15.489283] Chip[0] MCI_CRC_CTRL=38000000 ERR=0 [ 15.493836] [ 15.495418] -------------CHIP 1------------- [ 15.499711] Chip[1] DEVID=0x10021 [ 15.503043] Chip[1] DEV_NAME=scbt_a0 [ 15.506643] Chip[1] CHIPID=1 [ 15.509538] Chip[1] MOCHI_REV=0x184 [ 15.513038] Chip[1] node_off=2 [ 15.516109] Chip[1] EID=0 [ 15.518745] Chip[1] Node_CNT=2 [ 15.521814] Chip[1] IHB_CNT=1 [ 15.524794] Chip[1] Uplink=2 [ 15.527693] Chip[1] Parent Chip_Id=0 [ 15.531285] Chip[1] Parent dwn_hid=0 [ 15.534878] Chip[1] addr_base=0xf9800000 [ 15.538822] Chip[1] addr_size=0x400000 [ 15.542589] Chip[1] LinkSpeed=2 [ 15.545748] Chip[1] Pwr_State=0 [ 15.548900] Chip[1] Lanes=2 [ 15.552714] Chip[1] MCI_CRC_CTRL=0 ERR=0 [ 15.556654] [ 15.558241] ***************************************************** [ 15.565366] IHB 3 link not represent, don't set port state [ 15.574969] mci_cfg_crc mci_cfg_crc = a0000 [ 15.580283] wlwlan_platform_data_get(), (IoBase0)=(f9800000, f99fffff), more mapping space [ 15.588636] wlwlan_platform_data_get(), (IoBase1)=(f9a00000, f9afffff) [ 15.595243] wlwlan_platform_data_get(), carindex:1: ioBaseExt: (v,p)=(ffffff800273a000, fe000000) [ 15.604161] reg(1a800)=2021400h [ 15.607324] ==> This is W9064, rev=2 [ 15.610917] Revision: A0 [ 15.613467] Running on W9064 [ 15.616359] wlprobe wlpptr->ioBase0 = ffffff8002c00000 [ 15.621696] wlprobe wlpptr->ioBase1 = ffffff8002e80000 [ 15.627154] wlprobe: intr_shift=0 msix_num=32 [ 15.631536] (base, spi)=(f02a0040h, e0h) [ 15.635483] => wl_init_intr(),w_reg(ioBase1+30024h) = 38h [ 15.640910] => wl_init_intr(),w_reg(ioBase1+30018h) = 0h [ 15.646248] => wl_init_intr(),w_reg(ioBase1+1a82ch) = 0h [ 15.651586] => wl_init_intr(),w_reg(ioBase1+3002ch) = f02a0040h [ 15.657536] => wl_init_intr(),w_reg(ioBase1+30028h) = e0h [ 15.662961] ===> w_reg(ioBase1+30100h) = 0h [ 15.667767] ap8x f9800000.sc5_mci1: hframe base addr 5c6e0000 [ 15.673640] ====> Register kdumper successfully [ 15.678917] wlInit SSU pSsuBuf = ffffff8002f81000 pPhysSsuBuf = 000000005c900000 size=0x00200000 [ 15.687909] wlInit DSP pDspBuf = ffffff8002752000 pPhysDspBuf = 000000005c6f0000 size=0x00010000 [ 15.696826] wlInit wlpptr->pCmdBuf = ffffff800274d000 wlpptr->wlpd_p->pPhysCmdBuf = 5c234000 [ 15.705466] The current working directory is /lib/modules/4.4.120/wireless [ 15.712383] fw file: W9064-A0.bin [ 15.715720] read img file: /lib/modules/4.4.120/wireless/W9064-A0.bin... [ 15.910572] FW len = 452984 [ 15.914390] fw download start 88 [ 16.100203] FwSize = 452984 downloaded Size = 452984 currIteration 65480 [ 18.155373] wlFwDownload complete [ 18.155373] FwDownload time = 182566 us [ 18.155373] Radio Cal time = 2048433 us [ 18.166741] wlQMInit(), Interrupt shift = 0h [ 18.171061] => wlget_extmembuf(), using bootmem_2 [ 18.171061] rsvd mem: pbuf=76000000 vbuf=ffffffc076000000 size=4000000 [ 18.189807] => wlget_extmembuf(), using bootmem_3 [ 18.189807] rsvd mem: pbuf=7a000000 vbuf=ffffffc07a000000 size=6000000 [ 18.212318] => wlQMInit(), set qIntOffset = e0h [ 18.230981] => wlInit(), MAC_CONFIG_st->magic = 85h [ 18.235901] => wlInit(), MAC_STATUS_st->verCtrl[3] = f0000000h [ 18.242788] (v,p)=(ffffffc076000000, 76000000) [ 18.247255] rxSBinfoBaseAddr_v=ffffffc15cd00000, 5cd00000, 2048, 128 [ 18.253670] Major Version : 1 [ 18.256648] Minor Version : 1 [ 18.259633] Patch Version : 0 [ 18.262614] Num of Regions: 13 [ 18.265684] Num of Symbols: 0 [ 18.268662] region[ 0].address = 0x 135b40, region[ 0].length = 0x 418 [ 18.276007] region[ 1].address = 0x 20123800, region[ 1].length = 0x 800 [ 18.283352] region[ 2].address = 0x 0, region[ 2].length = 0x 8000 [ 18.290696] region[ 3].address = 0x 8000, region[ 3].length = 0x 8000 [ 18.298042] region[ 4].address = 0x 100000, region[ 4].length = 0x c0000 [ 18.305385] region[ 5].address = 0x 20000000, region[ 5].length = 0x 124000 [ 18.312730] region[ 6].address = 0x 90040000, region[ 6].length = 0x 8000 [ 18.320074] region[ 7].address = 0x 90050000, region[ 7].length = 0x 8000 [ 18.327417] region[ 8].address = 0x 90060000, region[ 8].length = 0x a000 [ 18.334766] region[ 9].address = 0x 90070000, region[ 9].length = 0x a000 [ 18.342109] region[10].address = 0x 90080000, region[10].length = 0x 8000 [ 18.349453] region[11].address = 0x 90088000, region[11].length = 0x 8000 [ 18.356795] region[12].address = 0x 90090000, region[12].length = 0x b000 [ 18.364138] wlFwGetHwSpecs pCmd = ffffff800274d000 [ 18.379049] mac version e0100 [ 18.382033] wlpptr->hwData.ulShalVersion:0085 [ 18.386412] Mac address = 00:50:43:00:0b:20 [ 18.390703] Mac_Init [ 18.397206] -->num tx desc 2048 num rx desc 16384 [ 18.447032] **Overwrite Clinet macid:31 [ 18.451230] [wlInit_monif] wlinitcnt=1, vmacIndex=33 [ 18.456481] wlmon_wdev1 monitor thread created [ 18.530965] SET tlv type=14 len=3 [ 18.534320] 64 00 00 [ 18.537859] SET tlv type=14 len=3 [ 18.541207] 65 00 00 [ 18.544748] SET tlv type=14 len=3 [ 18.548097] 66 00 01 [ 18.551657] SET tlv type=14 len=3 [ 18.555005] 67 00 01 security open wdev0 version: Driver : 10.14.2.0-W906x [SHAL 0.85] Firmware: 1.14.1[ 18.571882] br0: port 1(eth0) entered blocking state .0 [SHAL 0.85][ 18.577478] br0: port 1(eth0) entered disabled state MAC : 0.14.[ 18.583952] device eth0 entered promiscuous mode 1.0 [SHAL 0.85][ 18.591126] br0: port 2(wdev0ap0) entered blocking state wdev1 ve[ 18.596620] br0: port 2(wdev0ap0) entered disabled state rsion: Driver[ 18.603414] device wdev0ap0 entered promiscuous mode : 10.14.2.0-W9[ 18.610865] br0: port 3(wdev1ap0) entered blocking state 06x [SHAL 0.85] [ 18.616431] br0: port 3(wdev1ap0) entered disabled state Firmware: 1.14[ 18.623254] device wdev1ap0 entered promiscuous mode .1.0 [SHAL 0.85] MAC : 0.14.1.0 [SHAL 0.85] [ 18.646779] mvpp2 f2000000.ppv22 eth0: link up [ 18.654947] 8021q: adding VLAN 0 to HW filter on device eth0 [ 18.663116] setting rxantenna 0xf, 0xf [ 18.681100] setting txantenna 0xf, 0xff [ 18.699573] wlInterruptEnable(), w_reg(ffffff80022059c8)=0h [ 18.705177] wlInterruptEnable(), w_reg(ffffff80022059c8)=1ffff00h [ 18.712659] setting rxantenna 0x0, 0xf [ 18.730327] setting txantenna 0x0, 0xf [ 18.748309] wlInterruptEnable(), w_reg(ffffff8002e859c8)=0h [ 18.753913] wlInterruptEnable(), w_reg(ffffff8002e859c8)=1ffff00h [ 18.761470] Build_IE_192 80MHz or less [ 18.765473] WTP_nable=0 macmode=0 tunnel_mode=0 RFID=0 WLANID=0 [ 18.772883] Build_IE_192 80MHz or less [ 18.776915] WTP_nable=0 macmode=0 tunnel_mode=0 RFID=1 WLANID=0 [ 18.786313] br0: port 3(wdev1ap0) entered blocking state [ 18.791661] br0: port 3(wdev1ap0) entered forwarding state [ 18.797191] br0: port 2(wdev0ap0) entered blocking state [ 18.802532] br0: port 2(wdev0ap0) entered forwarding state [ 18.808056] br0: port 1(eth0) entered blocking state [ 18.813048] br0: port 1(eth0) entered forwarding state Starting telnetd: OK Starting WNC rcS... Starting dhcpd Starting telnetd dev: size erasesize name mtd0: 001a0000 00010000 "u-boot" mtd1: 00010000 00010000 "sharedenv" mtd2: 00010000 00010000 "reserved" mtd3: 00010000 00010000 "bootinfo" mtd4: 00010000 00010000 "mfg_info" mtd5: 00020000 00010000 "cookie" mtd6: 001a0000 00010000 "shadow_bootloader" mtd7: 00040000 00010000 "firmware" mtd8: 00010000 00010000 "fiq_info" mtd9: 00100000 00040000 "DTB" mtd10: 01200000 00040000 "Linux" mtd11: 1ea00000 00040000 "Filesystem" mtd12: 1fd00000 00040000 "Filesystem2" WNC Linux Revision: Marvell RXAM-C1.MRVL V1.0.8.2 lrwxrwxrwx 1 ftp 1002 15 Aug 24 2018 /etc/network.sh -> network-5g5g.sh wdev0 getopmode:48 wdev1 getopmode:48 / #

Linux printenv output and /etc/os-release:

Spoiler

/ # printenv
USER=root
SHLVL=1
HOME=/
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
RUNLEVEL=chk_data_crc
SHELL=/bin/sh
PWD=/
/ # cat /etc/os-release
NAME=Buildroot
VERSION=2015.11-00006-ge5a23eb-dirty
ID=buildroot
VERSION_ID=2015.11
PRETTY_NAME="Buildroot 2015.11"
MVEBU_RELEASE="16.08.0"
/ #

/ # printenv USER=root SHLVL=1 HOME=/ TERM=vt102 PATH=/sbin:/usr/sbin:/bin:/usr/bin RUNLEVEL=chk_data_crc SHELL=/bin/sh PWD=/ / # cat /etc/os-release NAME=Buildroot VERSION=2015.11-00006-ge5a23eb-dirty ID=buildroot VERSION_ID=2015.11 PRETTY_NAME="Buildroot 2015.11" MVEBU_RELEASE="16.08.0" / #

"Axel" printenv output:

Spoiler

Hit any key to stop autoboot:  0
Axel>> printenv
arch=arm
baudrate=115200
bl_ver=rxam-c1_V1.0.7.0
board=mvebu_armada-8k
board_name=mvebu_armada-8k
bootcmd=run bootcmd_nand
bootcmd_nand=nand read $fdt_addr 0x000000 0x100000&&nand read $loadaddr 0x100000 0x1200000&&setenv bootargs $console ubi.mtd=11,4096 root=ubi0:rootfs rootfstype=ubifs rw chk_data_crc rootdelay=2&&booti $loadaddr - $fdt_addr
bootcmd_ram=setenv bootargs $console root=/dev/ram rootfstype=ext2 rw && tftp $fdt_addr part.bin && bootm $fdt_addr
bootdelay=2
console=console=ttyS0,115200
cpu=armv8
eraseenv=env default -fa &&saveenv
ethact=mvpp2-0
ethaddr=00:50:43:00:15:10
ethprime=mvpp2-0
fdt_addr=0x1000000
fdt_high=0xffffffffffffffff
fdtcontroladdr=7f6eac60
fw_ver=rxam-c1_V1.0.7.0
gatewayip=10.4.50.254
hostname=Axel
initrd_high=0xffffffffffffffff
ipaddr=192.168.1.1
kernel_addr=0x2000000
loadaddr=0x2000000
nad=setenv dtb_image armada-3900-axis_$fw_ver.dtb && tftpboot $fdt_addr $dtb_image&&nand erase 0x000000 0x100000&&nand write $fdt_addr 0x000000 $filesize
naf=setenv fs_image rootfs_$fw_ver.ubi && tftpboot $fdt_addr $fs_image &&nand erase 0x1300000 0x1EA00000&&nand write $fdt_addr 0x1300000 $filesize
nak=setenv kernel_image Image_$fw_ver && tftpboot $fdt_addr $kernel_image &&nand erase 0x100000 0x1200000&&nand write $fdt_addr 0x100000 $filesize
netmask=255.255.255.0
nob=setenv bl_image flash-image_$bl_ver.bin && tftpboot $loadaddr $bl_image &&sf probe 0:0 && sf update $loadaddr 0 $filesize
rootpath=/srv/nfs/
serverip=192.168.1.254
soc=mvebu
stderr=serial@512000
stdin=serial@512000
stdout=serial@512000
upgradeall=run naf &&run nak &&run nad &&run nob&& reset
vendor=Marvell

Environment size: 1688/65532 bytes
Axel>>

Hit any key to stop autoboot: 0 Axel>> printenv arch=arm baudrate=115200 bl_ver=rxam-c1_V1.0.7.0 board=mvebu_armada-8k board_name=mvebu_armada-8k bootcmd=run bootcmd_nand bootcmd_nand=nand read $fdt_addr 0x000000 0x100000&&nand read $loadaddr 0x100000 0x1200000&&setenv bootargs $console ubi.mtd=11,4096 root=ubi0:rootfs rootfstype=ubifs rw chk_data_crc rootdelay=2&&booti $loadaddr - $fdt_addr bootcmd_ram=setenv bootargs $console root=/dev/ram rootfstype=ext2 rw && tftp $fdt_addr part.bin && bootm $fdt_addr bootdelay=2 console=console=ttyS0,115200 cpu=armv8 eraseenv=env default -fa &&saveenv ethact=mvpp2-0 ethaddr=00:50:43:00:15:10 ethprime=mvpp2-0 fdt_addr=0x1000000 fdt_high=0xffffffffffffffff fdtcontroladdr=7f6eac60 fw_ver=rxam-c1_V1.0.7.0 gatewayip=10.4.50.254 hostname=Axel initrd_high=0xffffffffffffffff ipaddr=192.168.1.1 kernel_addr=0x2000000 loadaddr=0x2000000 nad=setenv dtb_image armada-3900-axis_$fw_ver.dtb && tftpboot $fdt_addr $dtb_image&&nand erase 0x000000 0x100000&&nand write $fdt_addr 0x000000 $filesize naf=setenv fs_image rootfs_$fw_ver.ubi && tftpboot $fdt_addr $fs_image &&nand erase 0x1300000 0x1EA00000&&nand write $fdt_addr 0x1300000 $filesize nak=setenv kernel_image Image_$fw_ver && tftpboot $fdt_addr $kernel_image &&nand erase 0x100000 0x1200000&&nand write $fdt_addr 0x100000 $filesize netmask=255.255.255.0 nob=setenv bl_image flash-image_$bl_ver.bin && tftpboot $loadaddr $bl_image &&sf probe 0:0 && sf update $loadaddr 0 $filesize rootpath=/srv/nfs/ serverip=192.168.1.254 soc=mvebu stderr=serial@512000 stdin=serial@512000 stdout=serial@512000 upgradeall=run naf &&run nak &&run nad &&run nob&& reset vendor=Marvell Environment size: 1688/65532 bytes Axel>>

Leo Laohoo · ‎09-05-2021

Contact Cisco TAC and organize for an RMA.

Kurian Thampy · ‎09-06-2021

I'll open a case with TAC via email. What kind of device is this? Is this some kind of special purpose firmware instead of IOS XE?

Leo Laohoo · ‎09-06-2021

The factory did not load the firmware into the AP.