Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I seem to have a little radius trouble.I have two radius servers on a iPSK with radius SSID.Everything has worked just fine.But then things (hence this post) started , ehh , not working fine. A bit of investigation (packet captures) shows that the AP...
Hi, We have configured an SSID with enterprise security with Microsoft NPS radius and override VLAN TAG. It's our radius server which, depending on the PC group, assigns the Tunnel-PVT-GROUP-ID.Example: my SSID is called WIFI_TESTif my pc belongs to ...
Good day!From my app I have to connect to known wi-fi network. I have ssid and password of my dgme login (probably empty for our devices) and I can connect via NEHotspotConfiguration since iOS 11. But I need information is it possible to connect to k...
Hello everyoneWe work with a WLC 8540 (version 8.5.161.6) and Cisco 2802 and 3802 AP, and an external Radius server to perform authentication.We need to trace one or several clients on the WLC to see what messages we receive from the Radius, both for...
Hello, We are using a Cisco WLC 9800-40 running version 17.6.4 in a government customer environment in the Middle-East. In order to make the wireless solution adapt to the end users, the customer needs the SSID to be visible in Arabic instead of Eng...
I've had a Cisco WiFi network up for about 3 years. My organization purchased a bundle a couple of years before that that came with 2 Cisco 2500 series controllers, and 15 AP's. I guess it was just blind luck that during the initial deployment all th...
hi , i have a WLC 2504 and it is first time to configure it .after finishing the startup wizard i choose to save configuration , but when it reboots , there is no config at all and i should try the wizard again and again .
Hello forum teamI currently have a Cisco WLC 3504 which runs normallyfor some reason, i want to change the vlan and ip management on wlccan you please tell me the steps of WLC discovery options i need to change? (GUI Version)Thanks in advanced for yo...
Hi there,what would be the best way to extract all the configuration of this switch in order to do firmware update/reset and restart all from scratch but having a bit of a road map and reference to some of the settings?is there any step by step guide...
Curious if anyone has any experience using the T mount (MA-MNT-CLG-1) with a MR70?The Meraki webpage says for indoor MRs but we are wanting to use some MR70s indoors and need to mount them in a drop ceiling.
Hi i want to change vlan management of WLC and it gives me error belowconfig interface vlan management 100Blocked: Changing the management VLAN is blocked when system is in redundancy state as SSOplease how i can fix it thanks
Hello everyone, I am currently trying to install the new Cisco APs the company got that are C9105AXI-E.I have my APs in a native VLAN (we can say VLAN1).The wireless clients will be going through a 802.1x authentication process which will determine w...
Hi,I am using two products MR70 and MR46 for end users. Whenever I check internet speed via speedtest.net remaining connected on MR 46, I am getting Excellent upload/download speed(200 Mpbs plus on both). But When i connect over MR70 i get just 50 to...
We are having a WLC with access points that is providing WLAN access for users and assigning IPs in the range 192.168.5.0/24.We need to isolate 192.168.5.10 from communicating with other IPs in the same subnet. I know it will be layer 2 communication...
Hello guysi am new to Meraki AP.I have 4 AP MR42 which assigned to a dashboard, I want to move them to a other dashboard, all the old setup will go ? Do I I have to creat new SSID & new configurations ?What about the LIC ? Must enter it again ? Your ...
