11-04-2015 04:17 AM - edited 07-05-2021 04:10 AM
Hi,
I'm relevantly new to Cisco products. So, please pardon my basic questions.
I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I dont have controller. I need to configure this as standalone access point.
I tried all the basic steps and tried activating on both the radios but no luck. Can someone please guide me on how to configure this as AP.
I'm using web access to configure the AP.
Please help
Thanks,
Sagar
Solved! Go to Solution.
11-04-2015 04:27 AM
Hi Sagar,
Please check these posts to configure autonomous AP.
https://rscciew.wordpress.com/2014/05/24/single-ssid-configuration-on-autonomous-ap/
https://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on-autonomous-ap/
Regards
Dont forget to rate helpful posts
12-01-2015 09:23 PM
Maybe you should change the encryption from WPA/TKIP to WPA2/AES.
dot11 ssid Adknowledgeasia
authentication key-management wpa version 2
interface Dot11Radio0
encryption vlan 1 mode ciphers aes-ccm
Let us know if that helps.
-Scott
11-04-2015 04:27 AM
Hi Sagar,
Please check these posts to configure autonomous AP.
https://rscciew.wordpress.com/2014/05/24/single-ssid-configuration-on-autonomous-ap/
https://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on-autonomous-ap/
Regards
Dont forget to rate helpful posts
11-04-2015 04:39 AM
Hi Sandeep,
Thanks for your quick response. I tried to go throught the links above with Single SSID config but I'm unable to follow since it has vlan enabled and I dont have any vlan in my network.
Also, it will be great if you can share the links on how to configure the AP using webaccess.
Many Thanks,
Sagar
11-04-2015 04:50 AM
Still the conifg will be almost same.
Here is one more link:
https://supportforums.cisco.com/document/61936/autonomous-ap-and-bridge-basic-configuration-template
If i will get a link which used webGUI for AP conifg then I will paste it here.
Regards
Dont forget to rate helpful posts
11-05-2015 02:33 AM
Hi Sandeep,
I tried using the below link and configuring the access point but no luck. Its not broadcasting the SSID at all.
https://rscciew.wordpress.com/2014/05/24/single-ssid-configuration-on-autonomous-ap/
Please help
Thanks,
Sagar
11-05-2015 03:45 AM
Hi Sagar,
Did you configure this command:
dot11 ssid <ssid name>
Guest-mode ------> To broadcast the SSID
Regards
Dont orget to rate helpful posts
11-05-2015 08:05 PM
Yes, i did but still nothing coming up. Also, did you get webGUI link to config AP?
Appreciate all your help in this.
Thanks
11-05-2015 10:42 PM
Please paste your complete config here..
11-17-2015 08:34 PM
Hi Sandeep,
Sorry for delay in responding. My wifi is working now but I have to connect directly to my Cisco router and it doesnt work on my workstation. My Lan is in Vlan1 and i added this AP also in Vlan1 but still doesnt work.
Do let me know if Im missing something.
Thanks
Below is the config as requested.
Current configuration : 2068 bytes
!
! Last configuration change at 18:46:23 UTC Fri Jun 25 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
!
logging rate-limit console 9
enable secret 5
!
no aaa new-model
no ip cef
ip dhcp excluded-address 192.168.1.11
!
ip dhcp pool ADKPOOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
!
!
!
!
dot11 syslog
!
dot11 ssid Adknowledgeasia
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7
!
!
dot11 guest
!
!
!
username Cisco password 7
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip address
!
encryption vlan 1 mode ciphers tkip
!
ssid Adknowledgeasia
!
antenna gain 0
packet retries 64 drop-packet
station-role root
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
no ip address
shutdown
antenna gain 0
peakdetect
no dfs band block
packet retries 64 drop-packet
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
ip address 192.168.1.8 255.255.255.0
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
!
ip default-gateway 192.168.1.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
transport input all
!
end
adkap#
11-17-2015 11:21 PM
configuration is ok, What exactly you facing the issue with wi-fi ?
Regards
11-17-2015 11:57 PM
issue is: right now i have connected my wifi device directly to router and its in server room. I need to plug the device in workstation area on users desk.
When i do that, it doesnt works.
Please suggest.
Thanks
11-18-2015 12:43 AM
Also, I dont want to activate dhcp on this AP as it should pickup the dhcp from router. Please suggest the revised config too.
11-18-2015 02:41 AM
The AP configuration looks fine,
1. No you can not connect AP to a workstation then it will not work.
AP must connect to swicth/router. You can DHCP pool on swicth/router.
Regards
Dont forget to rate helpful posts
11-18-2015 02:47 AM
Can you share the steps on how to have only one pool between switch and router.
Thanks
11-18-2015 02:51 AM
HI Sagar,
Please paste the topology.
you told that you will connect the AP directly to router ???
Then create DHCP pool on Router:
ip dhcp pool Wireless
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 4.2.2.2
is there any switch in between ?
Regards
Dont forget to rate helpful posts
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide