Cisco Aironet AIR-AP1142N-E-K9 5ghz problem

[mehdi bahramipour]

hi we have aironet 1142

in FR 2.4 all thing is ok and client connect to ap

but in  5 ghz band , in webbase ap show up up but cliend didnt see the ssid of this ap

plz help

thx

[Leo Laohoo]

Sorry, I don't understand what you are trying to say.

Are you saying that your AP is in China?  If yes, do you have a WLC?

[mehdi bahramipour]

my problem is FR 5  didnt work ,

[Leo Laohoo]

What do mean by "FR 5"?

Sent from Cisco Technical Support Nintendo App

[mehdi bahramipour]

5 ghz band

[Scott Fella]

Post your show version and your show run-config

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

[mehdi bahramipour]

System Software Filename:	c1140-k9w7-tar.152-2.JB
System Software Version:	15.2(2)JB
Bootloader Version:	12.4(23c)JA6

interface Dot11Radio1

no ip address

!

ssid test

!

antenna gain 0

speed  basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6.

m7. m8. m9. m10. m11. m12. m13. m14. m15.

power client 17

channel 5825

station-role root

world-mode dot11d country-code RU both

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

and controller

interface Dot11Radio1

Radio AIR-AP1140A, Base Address 2401.c774.70b0, BBlock version 0.00, Software ve

rsion 4.10.1

Unused dynamic SQRAM memory: 0x00002B4C (10 KB)

Unused dynamic SDRAM memory: 0x00070B98 (450 KB)

Number of supported simultaneous BSSID on Dot11Radio1: 16

*************Carrier Set: China (UNI3) (CN) (-C)*************

Uniform Spreading Required: No

Configured Frequency: 5825 MHz  Channel 165

[Leo Laohoo]

Post the output to the command "sh ip int brie".

And remove this line:  channel 5825

[mehdi bahramipour]

ap#show ip int br

Interface                  IP-Address      OK? Method Status                Prot

ocol

BVI1                       192.168.0.70    YES NVRAM  up                    up

Dot11Radio0                unassigned      YES NVRAM  up                    up

Dot11Radio1                unassigned      YES NVRAM  up                    up

GigabitEthernet0           unassigned      YES NVRAM  up                    up

[Scott Fella]

post the wlc show run-config no ap

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

[art-barrera]

Given the filename of the code running "w7" indicates  standalone deployment.  Your interface output shows the 5GHz radio (Dot11Radio1) on so I'm assuming you just can't "see" the SSID from your station.  Look at your config under the dot11 ssid "ssid name" section and look for the config statement guest-mode.  This will instruct the ap to broadcast the ssid that you defined.  I'm assuming that you have a different SSID configured for each radio given that you "see" the ssid under your 2.4GHz radio.   //art

[Scott Fella]

Haha... Got confused:). Can you post your whole show run-config

Sent from Cisco Technical Support iPhone App

[Abhishek Abhishek]

Hello Mehdi,

As per your query i can suggest you the following solution-

Data Rates Supported in Aironet 1140 Series Access Point

802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps

802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps

802.11n data rates (2.4 GHz and 5 GHz):

For more information please refer to the link -

http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10092/datasheet_c78-502793.html

Hope this will help you.

[mehdi bahramipour]

hi this is my config ,

unfortunately i cant work with 5 ghz band yet pls check this thanks

!

! Last configuration change at 23:23:49 UTC Mon Mar 1 1993

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname ap

!

!

logging rate-limit console 9

enable secret 5 $

no aaa new-model

ip cef

!

!

!

dot11 syslog

!

dot11 ssid golestan

   authentication open

   guest-mode

!

dot11 ssid golestan2

   authentication open

   guest-mode

!

!

crypto pki token default removal timeout 0

!

!

username Cisco password 7 112A1016141D

!

!

bridge irb

!

!

!

interface Dot11Radio0

no ip address

!

ssid golestan2

!

antenna gain 0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio1

no ip address

!

ssid golestan

!

antenna gain 0

speed  basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.

power client 17

channel 5745

station-role root

world-mode dot11d country-code US both

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface GigabitEthernet0

no ip address

duplex auto

speed auto

no keepalive

bridge-group 1

bridge-group 1 spanning-disabled

no bridge-group 1 source-learning

!

interface BVI1

ip address 192.168.0.70 255.255.255.0

!

ip forward-protocol nd

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

ip route 0.0.0.0 0.0.0.0 192.168.0.1

!

snmp-server community cisco RW

bridge 1 route ip

!

!

wlccp ap username root password 7 06000A25435C08

wlccp ap wds ip address 192.168.0.3

wlccp wds priority 1 interface BVI1

wlccp wnm ip address 192.168.0.3

!

line con 0

line vty 0 4

password 7 01300F175804

login

transport input all

!

end

[Leo Laohoo]

Can you please post the following outputs:

1.  sh inventory;

2.  sh version; and

3.  dir