Cisco AP flashes continuously green red

Henny · ‎12-11-2021

Hi,

i have a 2802i running MobilityExpress 8.10.162.0 as primary controller and prefered master (AP1).

I successfully added a 2702i as subordinate AP (AP2).

So far everything looks good, I have no errors. But the AP2 keeps blinking red green although clients can connect successfully.

Someone an idea?

marce1000 · ‎12-11-2021

- Could be a power(ing) issue , in a way that radios and antennas operate but not at 'full strength'. Connect to the ap and issue the command show logging, ideally do this just after the ap has been booted , check for info's.

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Henny · ‎12-11-2021

Hi marce1000,

at the moment there is no other device connected to this switch. Power consumption is 6.8W (AP2) from available 130W.

The AP was before used as autonomous AP. I converted it to LWAP and did a factory reset via mode button. Is it possible that there are leftovers from the prior config? I can see BVI interfaces and vlans which are not in my network. Could these cause the problem?

Spoiler

*Mar  1 00:00:17.951: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar  1 00:00:18.411: Registering HW DTLS

*Mar  1 00:00:19.279: Starting Ethernet promiscuous mode
*Mar  1 00:00:21.595: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:21.595: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar  1 00:00:24.103: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar  1 00:00:24.215: loading Power Tables from ram:/U2.bin. Class = UX
*Mar  1 00:00:24.219:  record size of 3ss: 1168 read_ptr: 61590F6

*Mar  1 00:00:29.415: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar  1 00:00:29.463: loading Power Tables from ram:/U5.bin. Class = UX
*Mar  1 00:00:29.499:  record size of vht: 2904 read_ptr: 61590F6
APAVC Registering AVC licences on the AP to make sure we enable advanced PP

*Mar  1 00:00:30.915: SCHED: Ethernet Bridge Process: install watched boolean System Initialized(6141338), os:1 ah:0APAVC Protocol list already initialized.

*Mar  1 00:00:30.915: Start STILE Activation
APAVC: Succeeded to activate all the STILE protocols.
APAVC: Registering with CFT

*Mar  1 00:00:31.167: APAVC: CFT registration of delete callback succeeded
APAVC: Reattaching  Original Buffer pool for system use

*Mar  1 00:00:32.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar  1 00:00:32.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar  1 00:00:33.783: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Mar  1 00:00:33.783: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Mar  1 00:00:33.783: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Dec 10 06:54:17.099: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 39
*Dec 10 06:54:17.099: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 39
*Dec 10 06:54:17.111: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JK6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2021 by Cisco Systems, Inc.
Compiled Sat 24-Jul-21 00:50 by mcpre
*Dec 10 06:54:17.111: %SNMP-5-COLDSTART: SNMP agent on host Service16.AP2 is undergoing a cold start
*Dec 10 06:54:17.199: SCHED: Ethernet Bridge Process: remove watched boolean System Initialized(6141338)
*Dec 10 06:54:17.199: SCHED: Ethernet Bridge Process: install watched queue Soap BVI input queue(D129288), os:0 ah:0
*Dec 10 06:54:18.695: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Dec 10 06:54:19.159: %LINK-5-CHANGED: Interface GigabitEthernet1, changed state to administratively down
*Dec 10 06:54:26.151: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Dec 10 06:54:26.151: DPAA Initialization Complete
*Dec 10 06:54:26.151: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Dec 10 06:54:26.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Dec 10 06:54:26.783: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - EASY_ADMIN is not set, turn off easy admin service!

*Dec 10 06:54:26.783: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - Easy Admin is not enabled, turn it off!

*Dec 10 06:54:26.799: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 39
*Dec 10 06:54:26.799: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 39
*Dec 10 06:54:26.819: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Dec 10 06:54:26.823: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 10 06:54:26.827: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Dec 10 06:54:26.847: Starting Ethernet promiscuous modelwapp_crypto_init: MIC Present and Parsed Successfully

*Dec 10 06:54:26.999: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Dec 10 06:54:26.999: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 10 06:54:27.823: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 10 06:54:27.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Dec 10 06:54:35.443: Currently running a Release Image

*Dec 10 06:54:35.467: Using SHA-2 signed certificate for image signing validation.
*Dec 10 06:54:47.807: AP image integrity check PASSED

*Dec 10 06:54:47.879: Non-recovery image. PNP Not required.

*Dec 10 06:54:47.891: Cert ISSUER (39): cn=Cisco Manufacturing CA SHA2,o=Cisco

*Dec 10 06:54:47.915: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Dec 10 06:54:47.919: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Dec 10 06:54:47.927:
Note: A random mac address of 0000.0c21.fcc8
      has been chosen for BVI in bridge group  3 since the selected mac address
      is already being used by Bridge Group 2.
*Dec 10 06:54:47.927:
      Ensure that this address is unique.

*Dec 10 06:54:47.935:
Note: A random mac address of 0000.0c21.fcd0
      has been chosen for BVI in bridge group  4 since the selected mac address
      is already being used by Bridge Group 2.
*Dec 10 06:54:47.935:
      Ensure that this address is unique.

*Dec 10 06:54:47.939: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 10 06:54:49.047: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 10 06:54:49.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 10 06:54:50.047: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 10 06:54:50.275: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 10 06:54:50.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI2, changed state to up
*Dec 10 06:54:50.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI3, changed state to up
*Dec 10 06:54:50.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI4, changed state to up
*Dec 10 06:54:51.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to upcreating PnP template view
creating PnP template view for eWLC tag support

*Dec 10 06:54:58.327: Logging LWAPP message to 255.255.255.255.

*Dec 10 06:54:58.331: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 0 CLI Request Triggered
*Dec 10 06:54:59.331: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 started - CLI initiated
*Dec 10 06:55:19.343: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

*Dec 11 17:21:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.199.6 peer_port: 5246
*Dec 11 17:21:36.243: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.199.6 peer_port: 5246
*Dec 11 17:21:36.243: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.199.6
*Dec 11 17:21:36.299: %LWAPP-4-CLIENTEVENTLOG:
Checksum required saved version = 8.10.162.0, file flash:/lwapp_reap.cfg
*Dec 11 17:21:36.427: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 21
*Dec 11 17:21:36.439: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 11 17:21:36.447: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 56
*Dec 11 17:21:36.447: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 21
*Dec 11 17:21:36.447: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 21
*Dec 11 17:21:36.451: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 11 17:21:36.459: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 27
*Dec 11 17:21:36.463: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 56
*Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 21
*Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Dec 11 17:21:37.087: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
*Dec 11 17:21:37.267: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 11 17:21:37.267: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 11 17:21:37.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 11 17:21:37.535: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Service16.WLCWLAN id 1, SSID Service_16, L2ACL , L2ACL AP
capwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config

*Dec 11 17:21:37.767: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 11 17:21:37.775: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 11 17:21:38.727: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 11 17:21:38.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Dec 11 17:21:38.791: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Dec 11 17:21:38.831: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 11 17:21:38.839: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 11 17:21:38.847: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 11 17:21:39.811: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Dec 11 17:21:39.823: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Dec 11 17:21:39.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Dec 11 17:21:39.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 11 17:21:40.467: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 11 17:21:40.671: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 11 17:21:40.867: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to resetlwapp_reap_config_webauth: cannot get ssid_cfg for slotId 1, vapID 2
lwapp_reap_config_webauth: failed to config webauth for  vapID 2

*Dec 11 17:21:40.887: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 27
*Dec 11 17:21:40.895: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Dec 11 17:21:40.907: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Dec 11 17:21:41.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 11 17:21:41.675: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Dec 11 17:21:41.695: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 11 17:21:41.703: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 11 17:21:41.711: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 11 17:21:42.179: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
*Dec 11 17:21:42.695: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Dec 11 17:21:42.703: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 11 17:21:42.735: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 11 17:21:42.743: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 11 17:21:42.751: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 11 17:21:43.735: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 11 17:21:43.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Dec 11 17:21:43.771: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 11 17:21:44.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Dec 11 17:21:58.447: %CLEANAIR-6-STATE: Slot 0 enabled
Dec 11 17:22:10.267: %CLEANAIR-6-STATE: Slot 1 enabled

*Mar 1 00:00:17.951: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15) *Mar 1 00:00:18.411: Registering HW DTLS *Mar 1 00:00:19.279: Starting Ethernet promiscuous mode *Mar 1 00:00:21.595: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up *Mar 1 00:00:21.595: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up *Mar 1 00:00:24.103: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4) *Mar 1 00:00:24.215: loading Power Tables from ram:/U2.bin. Class = UX *Mar 1 00:00:24.219: record size of 3ss: 1168 read_ptr: 61590F6 *Mar 1 00:00:29.415: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4) *Mar 1 00:00:29.463: loading Power Tables from ram:/U5.bin. Class = UX *Mar 1 00:00:29.499: record size of vht: 2904 read_ptr: 61590F6 APAVC Registering AVC licences on the AP to make sure we enable advanced PP *Mar 1 00:00:30.915: SCHED: Ethernet Bridge Process: install watched boolean System Initialized(6141338), os:1 ah:0APAVC Protocol list already initialized. *Mar 1 00:00:30.915: Start STILE Activation APAVC: Succeeded to activate all the STILE protocols. APAVC: Registering with CFT *Mar 1 00:00:31.167: APAVC: CFT registration of delete callback succeeded APAVC: Reattaching Original Buffer pool for system use *Mar 1 00:00:32.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Mar 1 00:00:32.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down *Mar 1 00:00:33.783: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10 *Mar 1 00:00:33.783: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Mar 1 00:00:33.783: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source *Dec 10 06:54:17.099: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 39 *Dec 10 06:54:17.099: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 39 *Dec 10 06:54:17.111: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JK6, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2021 by Cisco Systems, Inc. Compiled Sat 24-Jul-21 00:50 by mcpre *Dec 10 06:54:17.111: %SNMP-5-COLDSTART: SNMP agent on host Service16.AP2 is undergoing a cold start *Dec 10 06:54:17.199: SCHED: Ethernet Bridge Process: remove watched boolean System Initialized(6141338) *Dec 10 06:54:17.199: SCHED: Ethernet Bridge Process: install watched queue Soap BVI input queue(D129288), os:0 ah:0 *Dec 10 06:54:18.695: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up *Dec 10 06:54:19.159: %LINK-5-CHANGED: Interface GigabitEthernet1, changed state to administratively down *Dec 10 06:54:26.151: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16) *Dec 10 06:54:26.151: DPAA Initialization Complete *Dec 10 06:54:26.151: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited *Dec 10 06:54:26.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up *Dec 10 06:54:26.783: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - EASY_ADMIN is not set, turn off easy admin service! *Dec 10 06:54:26.783: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information - Easy Admin is not enabled, turn it off! *Dec 10 06:54:26.799: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 39 *Dec 10 06:54:26.799: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 39 *Dec 10 06:54:26.819: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10 *Dec 10 06:54:26.823: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up *Dec 10 06:54:26.827: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Dec 10 06:54:26.847: Starting Ethernet promiscuous modelwapp_crypto_init: MIC Present and Parsed Successfully *Dec 10 06:54:26.999: %SSH-5-ENABLED: SSH 2.0 has been enabled *Dec 10 06:54:26.999: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up *Dec 10 06:54:27.823: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down *Dec 10 06:54:27.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down *Dec 10 06:54:35.443: Currently running a Release Image *Dec 10 06:54:35.467: Using SHA-2 signed certificate for image signing validation. *Dec 10 06:54:47.807: AP image integrity check PASSED *Dec 10 06:54:47.879: Non-recovery image. PNP Not required. *Dec 10 06:54:47.891: Cert ISSUER (39): cn=Cisco Manufacturing CA SHA2,o=Cisco *Dec 10 06:54:47.915: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10 *Dec 10 06:54:47.919: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Dec 10 06:54:47.927: Note: A random mac address of 0000.0c21.fcc8 has been chosen for BVI in bridge group 3 since the selected mac address is already being used by Bridge Group 2. *Dec 10 06:54:47.927: Ensure that this address is unique. *Dec 10 06:54:47.935: Note: A random mac address of 0000.0c21.fcd0 has been chosen for BVI in bridge group 4 since the selected mac address is already being used by Bridge Group 2. *Dec 10 06:54:47.935: Ensure that this address is unique. *Dec 10 06:54:47.939: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset *Dec 10 06:54:49.047: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up *Dec 10 06:54:49.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset *Dec 10 06:54:50.047: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up *Dec 10 06:54:50.275: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up *Dec 10 06:54:50.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI2, changed state to up *Dec 10 06:54:50.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI3, changed state to up *Dec 10 06:54:50.939: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI4, changed state to up *Dec 10 06:54:51.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to upcreating PnP template view creating PnP template view for eWLC tag support *Dec 10 06:54:58.327: Logging LWAPP message to 255.255.255.255. *Dec 10 06:54:58.331: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 0 CLI Request Triggered *Dec 10 06:54:59.331: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 started - CLI initiated *Dec 10 06:55:19.343: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS. *Dec 11 17:21:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.199.6 peer_port: 5246 *Dec 11 17:21:36.243: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.199.6 peer_port: 5246 *Dec 11 17:21:36.243: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.199.6 *Dec 11 17:21:36.299: %LWAPP-4-CLIENTEVENTLOG: Checksum required saved version = 8.10.162.0, file flash:/lwapp_reap.cfg *Dec 11 17:21:36.427: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 21 *Dec 11 17:21:36.439: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down *Dec 11 17:21:36.447: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 56 *Dec 11 17:21:36.447: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 21 *Dec 11 17:21:36.447: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 21 *Dec 11 17:21:36.451: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset *Dec 11 17:21:36.459: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 27 *Dec 11 17:21:36.463: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down *Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 56 *Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 21 *Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10 *Dec 11 17:21:37.067: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Dec 11 17:21:37.087: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash *Dec 11 17:21:37.267: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up *Dec 11 17:21:37.267: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up *Dec 11 17:21:37.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down *Dec 11 17:21:37.535: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Service16.WLCWLAN id 1, SSID Service_16, L2ACL , L2ACL AP capwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config *Dec 11 17:21:37.767: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down *Dec 11 17:21:37.775: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset *Dec 11 17:21:38.727: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up *Dec 11 17:21:38.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down *Dec 11 17:21:38.791: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Dec 11 17:21:38.831: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up *Dec 11 17:21:38.839: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down *Dec 11 17:21:38.847: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset *Dec 11 17:21:39.811: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10 *Dec 11 17:21:39.823: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Dec 11 17:21:39.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up *Dec 11 17:21:39.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down *Dec 11 17:21:40.467: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up *Dec 11 17:21:40.671: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down *Dec 11 17:21:40.867: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to resetlwapp_reap_config_webauth: cannot get ssid_cfg for slotId 1, vapID 2 lwapp_reap_config_webauth: failed to config webauth for vapID 2 *Dec 11 17:21:40.887: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 27 *Dec 11 17:21:40.895: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10 *Dec 11 17:21:40.907: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10 *Dec 11 17:21:41.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up *Dec 11 17:21:41.675: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down *Dec 11 17:21:41.695: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up *Dec 11 17:21:41.703: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down *Dec 11 17:21:41.711: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset *Dec 11 17:21:42.179: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up *Dec 11 17:21:42.695: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up *Dec 11 17:21:42.703: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down *Dec 11 17:21:42.735: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up *Dec 11 17:21:42.743: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down *Dec 11 17:21:42.751: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset *Dec 11 17:21:43.735: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up *Dec 11 17:21:43.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down *Dec 11 17:21:43.771: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up *Dec 11 17:21:44.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up Dec 11 17:21:58.447: %CLEANAIR-6-STATE: Slot 0 enabled Dec 11 17:22:10.267: %CLEANAIR-6-STATE: Slot 1 enabled

marce1000 · ‎12-11-2021

- To be 100% sure it is not a powering problem , you still need that output I talked about , just after boot. Or attach a console to it and scrutinize the boot-process. Watch for messages related to power-problems. I don't think it is a left-over from a previous config. If so the procedures I advise will point that out too.

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Henny · ‎12-11-2021

The output is below the picture in my last post.

marce1000 · ‎12-11-2021

- It would seem that the AP is not fully or in native capwap mode indeed (lwap) because of those bvi bridge group messages seen amongst others. I would reset the ap/(capwap) configuration again , have a look at this document : https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/99763-reset-lwappconfig-lap.html and use or instance capwap erase all

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Henny · ‎12-11-2021

I was able to reset the config of AP2 through the controller, but no success.

But now I found this: https://content.cisco.com/chapter.sjs?uri=/searchable/chapter/c/en/us/td/docs/wireless/controller/technotes/8-0/AP_Regulatory_Domain_DG/b_universal_AP_regulatory_domain_DG.html.xml

"You will see the APs LED blinking red and green even though the AP has obtained the IP address and joined the controller. This is because there is no regulatory domain set on the AP, and it has not been primed with the correct domain."

My 2702I shows up as: AIR-AP2702I-UXK9

AP Name                         Slots  AP Model              Ethernet MAC       Location              Country     IP Address       Clients  DSE Location
------------------------------  -----  --------------------  -----------------  --------------------  ----------  ---------------  -------  --------------
*Service16.AP1                   3      AIR-AP2802I-E-K9       00:be:***********  Dresden               DE          192.168.199.7    2        [0 ,0 ,0 ]
Service16.AP2                   2      AIR-AP2702I-UXK9       70:df:***********  Dresden               UX          192.168.199.8    0        [0 ,0 ,0 ]

marce1000 · ‎12-11-2021

>...and it has not been primed with the correct domain

Indeed ,ref : https://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g.html

>...Recognizing an Unprimed Universal AP

For an unprimed Lightweight AP:

On running the show ap summary command on the WLC, you see that the Country shows ‘UX’.

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '