02-29-2012 05:10 PM - edited 07-03-2021 09:41 PM
I'm having trouble configuring my router for wireless. I have followed guides but with no luck. Right now my issue is below with the radio. I cannot figure out why this is stuck in reset. I have reloaded the AP with no luck. Any suggestions? Config is posted below.
Interface IP-Address OK? Method Status Protocol
BVI1 10.20.50.35 YES DHCP up up
Dot11Radio0 unassigned YES NVRAM reset down
GigabitEthernet0 unassigned YES NVRAM up up
GigabitEthernet0.2 unassigned YES unset up up
CONFIG
########################ROUTER#######################
Current configuration : 5422 bytes
!
! Last configuration change at 18:55:56 PCTime Wed Feb 29 2012 by msetnes
! NVRAM config last updated at 18:37:40 PCTime Wed Feb 29 2012 by msetnes
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname XXXXXX
!
boot-start-marker
boot-end-marker
!
!
!
aaa new-model
!
!
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization network ciscocp_vpn_group_ml_1 local
!
!
!
!
!
aaa session-id common
memory-size iomem 10
clock timezone PCTime -6 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
ip source-route
!
!
!
ip dhcp excluded-address 10.20.30.1 10.20.30.99
ip dhcp excluded-address 10.20.50.1 10.20.50.31
!
ip dhcp pool LOCAL
import all
network 10.20.30.0 255.255.255.0
default-router 10.20.30.1
dns-server 8.8.8.8 8.8.4.4
!
ip dhcp pool WIFI
import all
network 10.20.50.0 255.255.255.0
default-router 10.20.30.1
dns-server 8.8.8.8 8.8.4.4
!
!
ip cef
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ipv6 cef
!
!
!
username XXXXXX privilege 15 secret 5 XXXXXXXX
!
!
!
!
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 1
!
bridge irb
!
!
!
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
description "Connection to internet"
ip address dhcp client-id FastEthernet4
ip flow ingress
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
!
interface wlan-ap0
description "Service module interface connecting to embedded AP"
ip unnumbered Vlan2
arp timeout 0
!
interface Wlan-GigabitEthernet0
description "Internal switch interface connecting to AP"
switchport trunk native vlan 2
switchport mode trunk
!
interface Vlan1
description "Local"
ip address 10.20.30.1 255.255.255.0
ip flow ingress
ip nat inside
ip virtual-reassembly in
!
interface Vlan2
description "Wireless"
ip address 10.20.50.1 255.255.255.0
ip flow ingress
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip nat inside source list 23 interface FastEthernet4 overload
ip route 0.0.0.0 0.0.0.0 dhcp
!
logging esm config
access-list 22 remark
access-list 23 permit 10.20.30.0 0.0.0.255
access-list 23 permit 10.20.50.0 0.0.0.255
!
!
!
!
!
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
!
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
!
end
#########################AP##########################
dot11 ssid XXXXXX
authentication open
guest-mode
!
!
!
username XXXXXX privilege 15 secret 5 XXXXXX
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
ssid SkyNET
!
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address dhcp
no ip route-cache
!
ip default-gateway 10.20.30.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
!
end
Solved! Go to Solution.
02-29-2012 06:39 PM
not the AP, but that one too. The GW in your dhcp scope is showing the wrong IP
Sent from Cisco Technical Support iPad App
02-29-2012 05:34 PM
when you define the VLAN under the SSID you need ti create the sub interface under the radio as well.
If your only going to have the one SSID the you can remove the VLAN from under the said and encryption statement.
Steve
Sent from Cisco Technical Support iPhone App
02-29-2012 05:56 PM
Thanks, this brought the radio back up. I seem to be connecting and disconnecting consistently. Is there something I'm missing in my config?
EDIT--
I removed encryption just to resolve this issue for now. My issue now is I am not able to talk outside of the wifi network. I can only ping within the 10.20.50.0 network.
02-29-2012 06:11 PM
nothing I'm noticing of the top of my head. Can you be more specific with the issue? Do you get an up address the drop or do you not get that far?
Sent from Cisco Technical Support iPhone App
02-29-2012 06:18 PM
I receive an IP address (10.20.50.36) I can only ping this wireless IP within the AP and router, nowhere else.
02-29-2012 06:21 PM
check your GW address according to your scope it's 10.20.30.1 which is VLAN 1. It should be 10.20.50.1 the VLAN 2 address.
Steve
Sent from Cisco Technical Support iPad App
02-29-2012 06:30 PM
I've corrected the default gateway on the AP to no avail. I still cannot talk between wireless and wired clients, as well as not being able to reach outside the network with WiFi.
02-29-2012 06:39 PM
not the AP, but that one too. The GW in your dhcp scope is showing the wrong IP
Sent from Cisco Technical Support iPad App
02-29-2012 06:48 PM
Removing the VLAN and encryption statements under dot11 ssid resolved the connecting issue
Changing the DHCP scope default router to 10.20.501 resolved the communication issue.
Both networks can talk now and both and reach externally.
Thanks Stephen, much appreciated.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide