- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 11:56 AM - edited 07-03-2021 11:50 PM
Hi,
We have multiple wlan's here in our Company.
Im having trouble with mac addresses which I registered BEFORE via mac filter
and DELETED it after couple of days.
Right now, I need to register this mac addresses again via MAC Filter but error appears below.
ERROR: User name 'xx:xx:xx:xx:xx:xx' is already used as a Mac Filter.
Need to specify unique MAC Address across Disabled Clients, AP auth,
Management users, Network users and Mac Filters
What can I do to be able to register the mac addresses that already removed to our WLC???
Thanks in advance for any help you can offer.
Solved! Go to Solution.
- Labels:
-
Aironet Access Points
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 02:24 PM
Well when I try to add a mac address that I already have on one of the filters to the other, I get the same error you see. So maybe on the command line issue the following:
show macfilter summary
show macfilter mesh
Maybe reboot the WLC and try again.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
*** Please rate helpful posts ***
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 12:22 PM
There are two spots that a mac filter is added. You can only have a mac address in only one of these spots. Verify that it is not in one of these spots.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
*** Please rate helpful posts ***
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 12:41 PM
Actually im using the 1st one when adding a mac address. But once I ready fill up the requirements to have this mac address to join my WLAN the said ERROR appears...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 01:16 PM
You need to check the other location to see if the mac address is listed there.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
*** Please rate helpful posts ***
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 02:17 PM
Hi Scott,
I Already did search other locations such as disable clients & AP Policies.. but isn't listed there.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 02:24 PM
Well when I try to add a mac address that I already have on one of the filters to the other, I get the same error you see. So maybe on the command line issue the following:
show macfilter summary
show macfilter mesh
Maybe reboot the WLC and try again.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
*** Please rate helpful posts ***
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 03:06 PM
Hi Scott,
Thanks a lot.. I really apprecited it..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-04-2013 05:23 PM
Did you figure it out?
Sent from Cisco Technical Support iPhone App
*** Please rate helpful posts ***
