01-22-2014 05:19 AM - edited 07-05-2021 12:01 AM
Hello,
I am trying to migrating AP 2600 series that came with autonomous image 15.2 to lightweight using the Cisco Prime Infrastructure built-in migration template.
The AP successfully downloads the image from an external TFTP server but fails at updating the environment variables.
The logs show that the AP should download a text file from Cisco Prime but fails to do so:
START: Detailed logging started at -> 01.22.2014_14.01.52
INFO: TELNET to device 10.32.148.225 done.
INFO: Privilege level is equal to 15.
INFO: Setting vty line completed.
INFO: Dumped Environmental variables.
INFO: AP is supported for Upgrade process
INFO: IOS version is greater than or equal to 12.3(7)JA.
INFO: AP has MIC installed already.
INFO: Station role is root.
INFO: Station role is root.
INFO: DNS and Domain name configured.
INFO: Mac address of device is 88:5a:92:17:2b:09
INFO: Completed Dot11Radio0 shutting.
INFO: Device set up done and time configured on device.
INFO: Run-config dumped.
INFO: AP is DHCP configured.
INFO: Hostname gbknwa2225sr
INFO: Dumped Environmental variables.
INFO: Starts loading recovery image, takes time based on link speed.
INFO: Image Loading done.
INFO: Copying updated Env. variable file to WCS local tftp server 10.70.165.165
INFO: Copying the Env. variable file from tftp server to device.
Copying the Env vars to device failed.
ERROR: Device Response ::
copy tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt flash:/env_vars
Destination filename [env_vars]?
%Warning:There is a file already existing with this name
Do you want to over write? [confirm]
Accessing tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt...
%Error opening tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt (Timed out)
gbknwa2225sr#
gbknwa2225sr#_tune_
gbknwa2225sr#
INFO: Un-shut radio 1 done.
END: Migration Process Failure: Copying Env_Vars to device failed.
What can I do to solve that ?
Many thanks for your help,
David
Solved! Go to Solution.
01-22-2014 12:32 PM
Hi David,
I think 2600 AP not supported on Prime Infra for autonomous to Ligtweight migration.
PI 1.2, 1.3, 1.4 , 2.0
Only these APs are supported: Autonomous to Lightweight Migration Support
Check this link:
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.4/configuration/guide/ctrlcfg.html
Hope it helps.
Regards
Dont forget to rate helpful posts
01-22-2014 05:28 AM
HI,
use the archive command
ap#archive download-sw /overwrite tftp://
Follow this link as it show the archive command
https://supportforums.cisco.com/docs/DOC-14960
http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
Regards
Dont forget to rate
01-22-2014 05:30 AM
Better to do with console access.
use mentioned above method and try again.
Regards
01-22-2014 07:28 AM
Hi, with the archive command, I could make it work.
But do you know why it did not work from Prime ?
01-22-2014 12:32 PM
Hi David,
I think 2600 AP not supported on Prime Infra for autonomous to Ligtweight migration.
PI 1.2, 1.3, 1.4 , 2.0
Only these APs are supported: Autonomous to Lightweight Migration Support
Check this link:
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.4/configuration/guide/ctrlcfg.html
Hope it helps.
Regards
Dont forget to rate helpful posts
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: