10-21-2013 11:28 AM - edited 07-04-2021 01:07 AM
Hello,
I am having an issue with getting mobility to form between a 2504 and a 5508 controller. Both WLCs are running 7.4.110.0 code. The 5508 is the guest anchor.
The 5508 has a management interface on the inside network and the guest traffic is on the DMZ. On the management interface, that network also hosts another wireless controller for that site. With the foreign anchor, which is at a remote site, the mobility group is coming up with the non guest anchor, but not the guest anchor. I only mention this because all of the controller control traffic is passing L3 to one controller, but is not working on the other. This was set up just to verify that the L3 traffic was reaching that network.
The controller (XYZ) that is in the same network as the guest anchor is a 2104 running 7.0.235.0.
GUEST ANCHOR
(Cisco Controller) >show mobility summary
Mobility Architecture ........................... Flat
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... GUEST
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x5f38
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 2
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast IP Status
bc:16:65:f8:68:60 10.0.200.100 GUEST 0.0.0.0 Up
ec:e1:a9:54:1e:20 10.44.200.10 ABC 0.0.0.0 Control Path Down
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... bc:16:65:f8:68:6f
IP Address....................................... 10.0.200.100
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.0.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 200
Quarantine-vlan.................................. 0
Active Physical Port............................. LAG (13)
Primary Physical Port............................ LAG (13)
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 10.44.200.250
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
FOREIGN ANCHOR
(Cisco Controller) >show mobility summary
Mobility Architecture ........................... Flat
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... ABC
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0xcb94
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 3
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast IP Status
00:24:97:8f:a8:60 10.0.200.10 XYZ 0.0.0.0 Up
bc:16:65:f8:68:60 10.0.200.100 GUEST 0.0.0.0 Control Path Down
ec:e1:a9:54:1e:20 10.44.200.10 ABC 0.0.0.0 Up
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... ec:e1:a9:54:1e:2f
IP Address....................................... 10.44.200.10
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.44.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 200
Quarantine-vlan.................................. 0
Active Physical Port............................. LAG (13)
Primary Physical Port............................ LAG (13)
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.1.6
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
Debugs:
FOREIGN ANCHOR
(Cisco Controller) >debug mobility keep-alive enable
(Cisco Controller) >*ethoipSocketTask: Oct 21 13:20:19.596: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1187:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:19.596: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1187:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:19.597: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:20:20.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:24.411: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=697:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:24.412: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=697:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:24.412: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:20:29.595: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1189:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:29.595: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1189:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:29.595: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:20:30.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:34.410: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=698:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:34.410: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=698:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:34.410: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:20:39.593: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1191:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:39.594: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1191:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:39.594: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:20:40.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:44.409: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=699:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:44.409: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=699:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:44.409: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:20:49.592: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1193:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:49.592: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1193:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:49.592: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:20:50.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:54.407: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=700:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:54.407: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=700:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:54.407: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:20:59.590: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1195:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:20:59.590: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1195:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:59.591: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:21:00.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:04.406: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=701:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:04.406: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=701:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:04.406: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:21:09.589: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1197:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:09.589: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1197:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:09.589: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:21:10.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:14.404: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=702:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:14.404: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=702:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:14.404: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:21:19.587: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1199:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:19.587: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1199:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:19.588: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:21:20.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:24.402: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=703:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:24.403: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=703:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:24.403: Updated client count to 0 for peer 10.0.200.100
*mmListen: Oct 21 13:21:29.386: Vlan List payload not found, ignoring ...
*mmListen: Oct 21 13:21:29.386: IP Address don't compare for client cc:3a:61:08:21:94 is 0
*mmListen: Oct 21 13:21:29.386: cc:3a:61:08:21:94 Ignoring Announce, client record for not found
*ethoipSocketTask: Oct 21 13:21:29.586: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1201:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:29.586: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1201:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:29.586: Updated client count to 0 for peer 10.0.200.10
*mmListen: Oct 21 13:21:30.386: Vlan List payload not found, ignoring ...
*mmListen: Oct 21 13:21:30.386: IP Address don't compare for client cc:3a:61:08:21:94 is 0
*mmListen: Oct 21 13:21:30.386: cc:3a:61:08:21:94 Ignoring Announce, client record for not found
*mmMobility: Oct 21 13:21:30.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:34.401: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=704:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:34.401: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=704:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:34.401: Updated client count to 0 for peer 10.0.200.100
*ethoipSocketTask: Oct 21 13:21:39.585: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.10:version=02:SeqNo=1203:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:39.585: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.10:version=02:SeqNo=1203:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:39.585: Updated client count to 0 for peer 10.0.200.10
*mmMobility: Oct 21 13:21:40.761: Mobility Member 10.0.200.100 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:44.399: Keepalive:VALID:ETHOIP_OP_REQ:Received from 10.0.200.100:version=02:SeqNo=705:receiverStatusOnTransmitter=1
*ethoipSocketTask: Oct 21 13:21:44.400: Keepalive:VALID:ETHOIP_OP_RESP:Sent to 10.0.200.100:version=02:SeqNo=705:receiverStatusOnTransmitter=0
GUEST ANCHOR
(Cisco Controller) >debug mobility keep-alive enable
(Cisco Controller) >*mmListen: Oct 21 13:20:10.103: MAC: 00:24:97:8f:a8:60 not found in Mobility Database
*mmMobility: Oct 21 13:20:24.918: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=697:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:20:24.918: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:24.929: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=697:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:24.929: Updated client count to 0 for peer 10.44.200.10
*mmMobility: Oct 21 13:20:34.918: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=698:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:20:34.918: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:34.929: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=698:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:34.929: Updated client count to 0 for peer 10.44.200.10
*mmListen: Oct 21 13:20:40.103: MAC: 00:24:97:8f:a8:60 not found in Mobility Database
*mmMobility: Oct 21 13:20:44.918: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=699:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:20:44.918: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:44.929: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=699:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:44.929: Updated client count to 0 for peer 10.44.200.10
*mmMobility: Oct 21 13:20:54.918: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=700:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:20:54.918: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:20:54.929: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=700:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:20:54.929: Updated client count to 0 for peer 10.44.200.10
*mmMobility: Oct 21 13:21:04.918: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=701:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:21:04.918: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:04.929: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=701:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:04.929: Updated client count to 0 for peer 10.44.200.10
*mmListen: Oct 21 13:21:10.103: MAC: 00:24:97:8f:a8:60 not found in Mobility Database
*mmMobility: Oct 21 13:21:14.737: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=702:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:21:14.737: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:14.748: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=702:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:14.748: Updated client count to 0 for peer 10.44.200.10
*mmMobility: Oct 21 13:21:24.737: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=703:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:21:24.737: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:24.748: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=703:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:24.748: Updated client count to 0 for peer 10.44.200.10
*mmListen: Oct 21 13:21:29.721: MAC: 00:24:97:8f:a8:60 not found in Mobility Database
*mmListen: Oct 21 13:21:30.721: MAC: 00:24:97:8f:a8:60 not found in Mobility Database
*mmMobility: Oct 21 13:21:34.737: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=704:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:21:34.737: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:34.748: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=704:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:34.748: Updated client count to 0 for peer 10.44.200.10
*mmListen: Oct 21 13:21:39.921: MAC: 00:24:97:8f:a8:60 not found in Mobility Database
*mmMobility: Oct 21 13:21:44.737: Keepalive:VALID:ETHOIP_OP_REQ:Sent to 10.44.200.10:version=02:SeqNo=705:receiverStatusOnTransmitter=1
*mmMobility: Oct 21 13:21:44.737: Mobility Member 10.44.200.10 detected DOWN status 2, cleaning up client entries
*ethoipSocketTask: Oct 21 13:21:44.748: Keepalive:VALID:ETHOIP_OP_RESP:Received from 10.44.200.10:version=02:SeqNo=705:receiverStatusOnTransmitter=0
*ethoipSocketTask: Oct 21 13:21:44.748: Updated client count to 0 for peer 10.44.200.10
Any ideas?
10-21-2013 12:38 PM
It's looks like your mobility member configuration is wrong.
As per the below line "ec:e1:a9:54:1e:20" WLC should be in XYZ mobility domain.
ec:e1:a9:54:1e:20 10.44.200.10 XYZ 0.0.0.0 Up
But you have configured it for different mobility domain name in the first controller.
ec:e1:a9:54:1e:20 10.44.200.10 ABC 0.0.0.0 Control Path Down
Please check the mobility members configuration again & let us know.
HTH
Rasika
**** Pls rate all useful responses ****
10-21-2013 01:06 PM
I made some modifications because I believe I messed it up when sanitizing it.
There are three controllers
XYZ and GUEST are L2 adjacent.
ABC is across a WAN link.
ABC needs to connect to GUEST.
XYZ and ABC are connected only to show that the L3 path is working correctly.
Here is a quick diagram to help grasp the situation.
10-21-2013 01:39 PM
Hi Jacob,
Thanks for the diagram posted, it really helped to understand what you are trying to do. If you simply want guest anchoring ABC to GUEST, simply configure the mobility group members as follows (I think you alreday done that).
config mobility group domain GUEST
config mobility group member add ec:e1:a9:54:1e:20 10.44.200.10 ABC
config mobility group domain ABC
config mobility group member add bc:16:65:f8:68:60 10.0.200.100 GUEST
If mobility tunnels not coming up you have to check UDP port 16666 & EoIP reachability between your two controllers. Do the following "mping" & "eping" testing from remote controller (mobility domain configured with ABC)
(WLC-ABC) >mping 10.0.200.100
(WLC-ABC) >eping 10.0.200.100
if both succuess your mobility tunnel should come up. If mping fail, then udp 16666 is blocked somewerhe your Guest WLC & remote WLC. If eping fails then EoIP is get blocked somewhere Guest WLC & remote.
HTH
Rasika
*** Pls rate all useful responses *****
10-21-2013 01:45 PM
eping is successful but mping fails.
Like I said, ABC can eping and mping XYZ but not GUEST.
GUEST is connected to the same switch as XYZ with the same VLAN. I am not what could possibly be blocking that traffic layer 2.
10-21-2013 01:55 PM
Does these two controllers having same virtual IP address ? Makesure it is the case.
Also post "show sysinfo" output of both Guest & ABC controllers just to verify MAC address information again.
Rasika
10-28-2013 04:07 PM
Hello,
I am having the same issue with the software version 7.3.112. Did you find a solution?
Regards
Stephane
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide