How to change Cisco 3800 WLAN AP Console Log level and time stamp

[Gehrig_W]

Hello Cisco-WLAN-Experts,

in our effort to find more information about crashing Cleanair sensors on Cisco 3800 APs, I would like

to increase the console logging level and adjust the time stamps for the logging on the WLAN APs

The actual Console logging level is "notification".

How can I change this to "Debug" on a single 3800 WLAN AP? 

Also the time stamp of the WLAN AP log is one hour behind local german winter time.

How can I change the time on a single 3800 WLAN AP? 

By the way,

I tried to send the Syslog-Logging to our central Prime, but not all APs, nor all Console messages are appearing  there. 

Any idea how to transfer the complete AP Console logging to a central Syslog-Server ?

Console logging : Level - notification, Status - enabled

Syslog logging : Level - information, Status - active, IP - 10.200.67.67

System logging :
Feb 2 20:07:41 kernel: [*02/02/2022 20:07:41.5255] chatter: wl0: Beacon PID : Previous: 6 Current: 3
Feb 2 20:17:00 kernel: [*02/02/2022 20:17:00.2958]
Feb 2 20:51:09 kernel: [*02/02/2022 20:17:00.2958] *** RSN ERROR: Received a data frame when no keys are plumbed
Feb 2 20:51:09 kernel: [*02/02/2022 20:51:09.8631] chatter: wl0: Beacon rate info: Previous: 251856640 Current: 251660032
Feb 2 20:51:09 kernel: [*02/02/2022 20:51:09.8631] chatter: wl0: Beacon PID : Previous: 3 Current: 0
Feb 2 21:05:43 kernel: [*02/02/2022 21:05:43.8531] chatter: wl0: Beacon rate info: Previous: 251660032 Current: 251856640
Feb 2 21:05:43 kernel: [*02/02/2022 21:05:43.8532] chatter: wl0: Beacon PID : Previous: 0 Current: 3
Feb 2 21:20:21 kernel: [*02/02/2022 21:20:21.5264] chatter: wl0: Beacon rate info: Previous: 251856640 Current: 252053248
Feb 2 21:20:21 kernel: [*02/02/2022 21:20:21.5264] chatter: wl0: Beacon PID : Previous: 3 Current: 6
Feb 2 21:34:59 kernel: [*02/02/2022 21:34:59.2067] chatter: wl0: Beacon rate info: Previous: 252053248 Current: 251856640
Feb 2 21:34:59 kernel: [*02/02/2022 21:34:59.2067] chatter: wl0: Beacon PID : Previous: 6 Current: 3
Feb 2 22:03:36 kernel: [*02/02/2022 22:03:36.0464] chatter: wl0: Beacon rate info: Previous: 251856640 Current: 251660032

Thank You for Your tips & tricks

Wini

[Leo Laohoo]

If the AP is joined to an AireOS WLC, then there are several options.  

1.  The AP can "synchronize" timezone with the WLC using the command "config ap timezone enable use-controller [ALL] [AP NAME]".

2.  The AP can have a timezone "delta" using the command "config ap timezone enable delta [ALL] [AP NAME] [DELTA of +23 to -23 hrs]"

[Gehrig_W]

Hello Leo,

You earn another 5 Points for this valuable tip.

Just tested the first comand successfully on one of our APs to fetch the time from a WLC, which is in contact with

an official Time-Server at our hospital using DNS resolution and SNTP.

ZOM-AP649#show clock
*10:36:14 UTC Fri Feb 4 202

(WLC-5520-1) >config ap timezone enable use-controller ZOM-AP649

Successfully enabled Time Zone for this AP

ZOM-AP649#show clock
*11:37:11 GMT Fri Feb 4 2022

I will activate this on all our WLAN APs.

Thank You very much.

Have a nice weekend

Wini