Solved: Re: Operational Status DOWN -WLC 2504 and LAP 3501

HEATH FREEL · ‎02-01-2012

The AP is connected to the WLC but keeps taking it's Raodio Down. As suggested I have played with the PoE settings to no avail.....

Wed Feb 1 18:30:36 2012	AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio interface reset. Status:NA
3	Wed Feb 1 18:30:36 2012	AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:ba:70:93:81:60 Cause=Admin change on Radio Status:Enable
4	Wed Feb 1 18:30:36 2012	AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Admin change on Radio Status:Disable
5	Wed Feb 1 18:25:32 2012	AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio interface reset. Status:NA
6	Wed Feb 1 18:25:29 2012	AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:ba:70:93:81:60 Cause=Radio reset due to Init. Status:NA

Any Ideas... I have checked everything... AP is in Port 4 of the WLC

Leo Laohoo · ‎02-03-2012

*Mar  1 00:00:12.988: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self                                 test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process=                                 "Init", ipl= 0, pid= 3

Now this is what I'm looking for!

Your 802.11b radio is dead. Please contact Cisco to get this WAP replaced.

View solution in original post

Scott Fella · ‎02-01-2012

You really should not connect any ap to the 2504 ports. I believe that Cisco does not support that setup.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***

HEATH FREEL · ‎02-01-2012

I had heard that once before, but don't buy it as we have others running on the built in ports... just not 3501's.

Why would they put a 4 port PoE switch in and not support it?

Anyway - when I move to a separate PoE switch I get the same issue.

Scott Fella · ‎02-01-2012

The thing is you can if you want, but if you open a TAC case, they will tell you to put the ap on a switch.

When the ap is on the switch, is the port negotiating correctly? Do you see just the radio go down or the ap itself. Take a look at the ap uptime and join time.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***

HEATH FREEL · ‎02-01-2012

I am trying in another switch right now....

The AP is up and I can see it in the WLC. At first boot radio is up but then goes down.

Switch.

show inline power

Fa0/20    auto   on         15.0    AIR-CAP3501I-A-K9   3     15.4

sh int fa0/20

Full-duplex, 100Mb/s,

Scott Fella · ‎02-01-2012

Do you have an SSID configured and enabled?

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***

HEATH FREEL · ‎02-01-2012

Yes - I have created two... One with my standard security parameters and one - open, no security- just to see if that was the issue..

Scott Fella · ‎02-01-2012

Okay... Well is it an issue with one ap or do you have other AP's that are working. Can you post your show run-config.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***

HEATH FREEL · ‎02-01-2012

Only have one LAP at the moment... The plan was once I got it working I would "upgrade" my AP's to LAP.

(Cisco Controller) show>run-config

Press Enter to continue...

System Inventory

NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"

PID: AIR-CT2504-K9, VID: V01, SN: PSJ154208DT

Burned-in MAC Address............................ D0:C2:82:E1:DA:A0

Maximum number of APs supported.................. 5

Press Enter to continue or to abort

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.116.0

Bootloader Version............................... 1.0.16

Field Recovery Image Version..................... 1.0.0

Firmware Version................................. PIC 16.0

Build Type....................................... DATA + WPS

System Name...................................... Cisco_e1:da:a4

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1279

IP Address....................................... 10.161.98.20

Last Reset....................................... Software reset

System Up Time................................... 0 days 3 hrs 20 mins 48 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

--More or (q)uit current module or to abort

Next Boot License Type........................... Permanent

Configured Country............................... CA - Canada

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +20 C

External Temperature............................. +24 C

Fan Status....................................... 4200 rpm

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 2

Number of Active Clients......................... 0

Burned-in MAC Address............................ D0:C2:82:E1:DA:A0

Maximum number of APs supported.................. 5

Press Enter to continue or to abort

Switch Configuration

802.3x Flow Control Mode......................... Disable

FIPS prerequisite features....................... Disabled

secret obfuscation............................... Enabled

Strong Password Check

eatures:

case-check ...........Enabled

consecutive-check ....Enabled

default-check .......Enabled

username-check ......Enabled

Press Enter to continue or to abort

Network Information

RF-Network Name............................. e2e

Web Mode.................................... Disable

Secure Web Mode............................. Enable

Secure Web Mode Cipher-Option High.......... Disable

Secure Web Mode Cipher-Option SSLv2......... Enable

Secure Shell (ssh).......................... Enable

Telnet...................................... Enable

Ethernet Multicast Forwarding............... Disable

Ethernet Broadcast Forwarding............... Disable

AP Multicast/Broadcast Mode................. Multicast Address : 0.0.0.0

IGMP snooping............................... Disabled

IGMP timeout................................ 60 seconds

IGMP Query Interval......................... 20 seconds

User Idle Timeout........................... 300 seconds

ARP Idle Timeout............................ 300 seconds

Cisco AP Default Master..................... Enabled

AP Join Priority............................ Disable

Mgmt Via Wireless Interface................. Disable

Mgmt Via Dynamic Interface.................. Disable

Bridge MAC filter Config.................... Enable

Bridge Security Mode........................ EAP

--More or (q)uit current module or to abort

Mesh Full Sector DFS........................ Enable

AP Fallback ................................ Enable

Web Auth Redirect Ports .................... 80

Web Auth Proxy Redirect ................... Disable

Fast SSID Change ........................... Disabled

IP/MAC Addr Binding Check .................. Enabled

Press Enter to continue or to abort

Port Summary

STP Admin Physical Physical Link Link

Pr Type Stat Mode Mode Status Status Trap POE

-- ------- ---- ------- ---------- ---------- ------ ------- -------

1 Normal Forw Enable Auto 100 Full Up Enable N/A

2 Normal Disa Enable Auto Auto Down Enable N/A

3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off

4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off

Press Enter to continue or to abort

AP Summary

Number of APs.................................... 1

Global AP User Name.............................. Not Configured

Global AP Dot1x User Name........................ Not Configured

AP Name Slots AP Model Ethernet MAC Location

Port Country Priority

------------------ ----- -------------------- ----------------- -----------

---- ---- ------- ------

APe8b7.48ac.1050 1 AIR-CAP3501I-A-K9 e8:b7:48:ac:10:50 default loc

tion 1 CA 1

AP Tcp-Mss-Adjust Info

AP Name TCP State MSS Size

------------------ -------- -------

APe8b7.48ac.1050 disabled -

Press Enter to continue or to abort

AP Location

Total Number of AP Groups........................ 1

Site Name........................................ default-group

Site Description.................................

WLAN ID Interface Network Admission Control Radio Po

icy

------- ----------- -------------------------- --------

---

1 management Disabled None

2 management Disabled None

AP Name Slots AP Model Ethernet MAC Location

Port Country Priority

------------------ ----- ------------------- ----------------- ------------

--- ---- ------- --------

APe8b7.48ac.1050 1 AIR-CAP3501I-A-K9 e8:b7:48:ac:10:50 default loca

ion 1 CA 1

Press Enter to continue or to abort

AP Config

Cisco AP Identifier.............................. 1

Cisco AP Name.................................... APe8b7.48ac.1050

Country code..................................... CA - Canada

Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A

AP Country code.................................. CA - Canada

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... e8:b7:48:ac:10:50

IP Address Configuration......................... Static IP assigned

IP Address....................................... 10.161.98.108

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 10.161.98.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

--More or (q)uit current module or to abort

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W Version .................................... 7.0.116.0

Boot Version ................................... 12.4.23.0

Mini IOS Version ................................ 7.0.112.74

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 1

--More or (q)uit current module or to abort

AP Model......................................... AIR-CAP3501I-A-K9

AP Image......................................... C3500-K9W8-M

IOS Version...................................... 12.4(23c)JA2

Reset Button..................................... Enabled

AP Serial Number................................. FTX1523E3L1

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 36 m 02 s

AP LWAPP Up Time................................. 0 days, 00 h 34 m 58 s

Join Date and Time............................... Wed Feb 1 19:55:09 2012

Join Taken Time.................................. 0 days, 00 h 01 m 03 s

Attributes for Slot 0

Radio Type................................... RADIO_TYPE_80211n-2.4

Administrative State ........................ ADMIN_ENABLED

Operation State ............................. DOWN

Radio Role .................................. ACCESS

CellId ...................................... 0

--More or (q)uit current module or to abort

Station Configuration

Configuration ............................. AUTOMATIC

Number Of WLANs ........................... 2

Medium Occupancy Limit .................... 100

CFP Period ................................ 4

CFP MaxDuration ........................... 60

BSSID ..................................... e8:ba:70:93:81:60

Operation Rate Set

1000 Kilo Bits........................... MANDATORY

2000 Kilo Bits........................... MANDATORY

5500 Kilo Bits........................... MANDATORY

11000 Kilo Bits.......................... MANDATORY

6000 Kilo Bits........................... SUPPORTED

9000 Kilo Bits........................... SUPPORTED

12000 Kilo Bits.......................... SUPPORTED

18000 Kilo Bits.......................... SUPPORTED

24000 Kilo Bits.......................... SUPPORTED

36000 Kilo Bits.......................... SUPPORTED

48000 Kilo Bits.......................... SUPPORTED

54000 Kilo Bits.......................... SUPPORTED

MCS Set

MCS 0.................................... SUPPORTED

--More or (q)uit current module or to abort

MCS 1.................................... SUPPORTED

MCS 2.................................... SUPPORTED

MCS 3.................................... SUPPORTED

MCS 4.................................... SUPPORTED

MCS 5.................................... SUPPORTED

MCS 6.................................... SUPPORTED

MCS 7.................................... SUPPORTED

MCS 8.................................... SUPPORTED

MCS 9.................................... SUPPORTED

MCS 10................................... SUPPORTED

MCS 11................................... SUPPORTED

MCS 12................................... SUPPORTED

MCS 13................................... SUPPORTED

MCS 14................................... SUPPORTED

MCS 15................................... SUPPORTED

Beacon Period ............................. 100

Fragmentation Threshold ................... 2346

Multi Domain Capability Implemented ....... TRUE

Multi Domain Capability Enabled ........... TRUE

Country String ............................ CA

Multi Domain Capability

Configuration ............................. AUTOMATIC

--More or (q)uit current module or to abort

First Chan Num ............................ 1

Number Of Channels ........................ 11

MAC Operation Parameters

Configuration ............................. AUTOMATIC

Fragmentation Threshold ................... 2346

Packet Retry Limit ........................ 64

Tx Power

Num Of Supported Power Levels ............. 8

Tx Power Level 1 .......................... 20 dBm

Tx Power Level 2 .......................... 17 dBm

Tx Power Level 3 .......................... 14 dBm

Tx Power Level 4 .......................... 11 dBm

Tx Power Level 5 .......................... 8 dBm

Tx Power Level 6 .......................... 5 dBm

Tx Power Level 7 .......................... 2 dBm

Tx Power Level 8 .......................... -1 dBm

Tx Power Configuration .................... AUTOMATIC

Current Tx Power Level .................... 1

Phy OFDM parameters

Configuration ............................. AUTOMATIC

--More or (q)uit current module or to abort

Current Channel ........................... 1

Extension Channel ......................... NONE

Channel Width.............................. 20 Mhz

Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

TI Threshold .............................. -50

Legacy Tx Beamforming Configuration ....... AUTOMATIC

Legacy Tx Beamforming ..................... DISABLED

Antenna Type............................... INTERNAL_ANTENNA

Internal Antenna Gain (in .5 dBi units).... 8

Diversity.................................. DIVERSITY_ENABLED

802.11n Antennas

A....................................... ENABLED

B....................................... ENABLED

C....................................... ENABLED

Performance Profile Parameters

Configuration ............................. AUTOMATIC

Interference threshold..................... 10 %

Noise threshold............................ -70 dBm

RF utilization threshold................... 80 %

Data-rate threshold........................ 1000000 bps

Client threshold........................... 12 clients

Coverage SNR threshold..................... 12 dB

--More or (q)uit current module or to abort

Coverage exception level................... 25 %

Client minimum exception level............. 3 clients

Rogue Containment Information

Containment Count............................ 0

CleanAir Management Information

CleanAir Capable......................... Yes

CleanAir Management Admin State.......... Disabled

CleanAir Management Operation State...... Down

Rapid Update Mode........................ Off

Spectrum Expert connection............... Enabled

CleanAir NSI Key....................... F5E484D89473C69EF67D707E24008

B0

Spectrum Expert Connections counter..... 0

CleanAir Sensor State.................... Radio is disabled. Turn ON ra

io to enable CleanAir functionality

AP does not have the 802.11a radio.

Press Enter to continue or to abort

AP Airewave Director Configuration

Number Of Slots.................................. 1

AP Name.......................................... APe8b7.48ac.1050

MAC Address...................................... e8:b7:48:ac:10:50

Slot ID........................................ 0

Radio Type..................................... RADIO_TYPE_80211b/g

Sub-band Type.................................. All

Noise Information

Noise Profile................................ PASSED

Interference Information

Interference Profile......................... PASSED

Load Information

Load Profile................................. PASSED

Receive Utilization.......................... 0 %

Transmit Utilization......................... 0 %

Channel Utilization.......................... 0 %

Attached Clients............................. 0 clients

Coverage Information

Coverage Profile............................. PASSED

Failed Clients............................... 0 clients

Client Signal Strengths

RSSI -100 dbm................................ 0 clients

--More or (q)uit current module or to abort

RSSI -92 dbm................................ 0 clients

RSSI -84 dbm................................ 0 clients

RSSI -76 dbm................................ 0 clients

RSSI -68 dbm................................ 0 clients

RSSI -60 dbm................................ 0 clients

RSSI -52 dbm................................ 0 clients

Client Signal To Noise Ratios

SNR 0 dB.................................. 0 clients

SNR 5 dB.................................. 0 clients

SNR 10 dB.................................. 0 clients

SNR 15 dB.................................. 0 clients

SNR 20 dB.................................. 0 clients

SNR 25 dB.................................. 0 clients

SNR 30 dB.................................. 0 clients

SNR 35 dB.................................. 0 clients

SNR 40 dB.................................. 0 clients

SNR 45 dB.................................. 0 clients

Nearby APs

Radar Information

Channel Assignment Information

Current Channel Average Energy............... unknown

Previous Channel Average Energy.............. unknown

Channel Change Count......................... 0

--More or (q)uit current module or to abort

Last Channel Change Time..................... Wed Feb 1 19:55:08 2012

Recommended Best Channel..................... 1

RF Parameter Recommendations

Power Level.................................. 1

RTS/CTS Threshold............................ 2347

Fragmentation Threshold...................... 2346

Antenna Pattern.............................. 0

Persistent Interference Devices

Class Type Channel DC (%%) RSSI (dBm) Last Update Time

------------------------- ------- ------ ---------- ---------------------

--

All third party trademarks are the property of their respective owners.

AP does not have the 802.11a radio.

Press Enter to continue or to abort

802.11a Configuration

802.11a Network.................................. Disabled

11nSupport....................................... Enabled

802.11a Low Band........................... Enabled

802.11a Mid Band........................... Enabled

802.11a High Band.......................... Enabled

802.11a Operational Rates

802.11a 6M Rate.............................. Mandatory

802.11a 9M Rate.............................. Supported

802.11a 12M Rate............................. Mandatory

802.11a 18M Rate............................. Supported

802.11a 24M Rate............................. Mandatory

802.11a 36M Rate............................. Supported

802.11a 48M Rate............................. Supported

802.11a 54M Rate............................. Supported

802.11n MCS Settings:

MCS 0........................................ Supported

MCS 1........................................ Supported

MCS 2........................................ Supported

MCS 3........................................ Supported

MCS 4........................................ Supported

MCS 5........................................ Supported

MCS 6........................................ Supported

--More or (q)uit current module or to abort

MCS 7........................................ Supported

MCS 8........................................ Supported

MCS 9........................................ Supported

MCS 10....................................... Supported

MCS 11....................................... Supported

MCS 12....................................... Supported

MCS 13....................................... Supported

MCS 14....................................... Supported

MCS 15....................................... Supported

802.11n Status:

A-MPDU Tx:

Priority 0............................... Enabled

Priority 1............................... Disabled

Priority 2............................... Disabled

Priority 3............................... Disabled

Priority 4............................... Enabled

Priority 5............................... Enabled

Priority 6............................... Disabled

Priority 7............................... Disabled

A-MSDU Tx:

Priority 0............................... Enabled

Priority 1............................... Enabled

Priority 2............................... Enabled

--More or (q)uit current module or to abort

Priority 3............................... Enabled

Priority 4............................... Enabled

Priority 5............................... Enabled

Priority 6............................... Disabled

Priority 7............................... Disabled

Rifs Rx ..................................... Enabled

Guard Interval .............................. Any

Beacon Interval.................................. 100

CF Pollable mandatory............................ Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 36

Default Tx Power Level........................... 0

DTPC Status..................................... Disabled

Fragmentation Threshold.......................... 2346

TI Threshold..................................... -50

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

--More or (q)uit current module or to abort

Call Admission Control (CAC) configuration

Voice AC:

Voice AC - Admission control (ACM)............ Disabled

Voice Stream-Size............................. 84000

Voice Max-Streams............................. 2

Voice max RF bandwidth........................ 75

Voice reserved roaming bandwidth.............. 6

Voice CAC Method ............................. Load-Based

Voice tspec inactivity timeout................ Disabled

CAC SIP-Voice configuration

SIP based CAC ................................ Disabled

SIP Codec Type ............................... CODEC_TYPE_G711

SIP call bandwidth ........................... 64

SIP call bandwith sample-size ................ 20

Video AC:

Video AC - Admission control (ACM)............ Disabled

Video max RF bandwidth........................ Infinite

Video reserved roaming bandwidth.............. 0

Best-effort AC - Admission control (ACM)...... Disabled

Background AC - Admission control (ACM)....... Disabled

Press Enter to continue or to abort

802.11a Advanced Configuration

AP Name MAC Address Admin State Operation Stat

Channel TxPower

-------------------------------- ------------------ ------------ --------------

---------- --------

Press Enter to continue or to abort

802.11a Airewave Director Configuration

RF Event and Performance Logging

Channel Update Logging......................... Off

Coverage Profile Logging....................... Off

Foreign Profile Logging........................ Off

Load Profile Logging........................... Off

Noise Profile Logging.......................... Off

Performance Profile Logging.................... Off

TxPower Update Logging......................... Off

Default 802.11a AP performance profiles

802.11a Global Interference threshold.......... 10 %

802.11a Global noise threshold................. -70 dBm

802.11a Global RF utilization threshold........ 80 %

802.11a Global throughput threshold............ 1000000 bps

802.11a Global clients threshold............... 12 clients

Default 802.11a AP monitoring

802.11a Monitor Mode........................... enable

802.11a Monitor Mode for Mesh AP Backhaul...... disable

802.11a Monitor Channels....................... Country channels

802.11a RRM Neighbor Discover Type............. Transparent

802.11a AP Coverage Interval................... 180 seconds

802.11a AP Load Interval....................... 60 seconds

--More or (q)uit current module or to abort

802.11a AP Noise Interval...................... 180 seconds

802.11a AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

Transmit Power Assignment Mode................. AUTO

Transmit Power Update Interval................. 600 seconds

Transmit Power Threshold....................... -70 dBm

Transmit Power Neighbor Count.................. 3 APs

Min Transmit Power............................. -10 dBm

Max Transmit Power............................. 30 dBm

Transmit Power Update Contribution............. SNI..

Transmit Power Assignment Leader............... Cisco_e1:da:a4 (10.161.98.20)

Last Run....................................... 13 seconds ago

Coverage Hole Detection

802.11a Coverage Hole Detection Mode........... Enabled

802.11a Coverage Voice Packet Count............ 100 packets

802.11a Coverage Voice Packet Percentage....... 50%

802.11a Coverage Voice RSSI Threshold.......... -80 dBm

802.11a Coverage Data Packet Count............. 50 packets

802.11a Coverage Data Packet Percentage........ 50%

802.11a Coverage Data RSSI Threshold........... -80 dBm

802.11a Global coverage exception level........ 25 %

802.11a Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

--More or (q)uit current module or to abort

Channel Assignment Mode........................ AUTO

Channel Update Interval........................ 600 seconds

Anchor time (Hour of the day).................. 0

Channel Update Contribution.................... SNI..

CleanAir Event-driven RRM option............... Disabled

CleanAir Event-driven RRM sensitivity.......... Medium

Channel Assignment Leader...................... Cisco_e1:da:a4 (10.161.98.20)

Last Run....................................... 13 seconds ago

DCA Sensitivity Level.......................... MEDIUM (15 dB)

DCA 802.11n Channel Width...................... 20 MHz

DCA Minimum Energy Limit....................... -95 dBm

Channel Energy Levels

Minimum...................................... unknown

Average...................................... unknown

Maximum...................................... unknown

Channel Dwell Times

Minimum...................................... unknown

Average...................................... unknown

Maximum...................................... unknown

802.11a 5 GHz Auto-RF Channel List

Allowed Channel List......................... 36,40,44,48,52,56,60,64,149,

153,157,161

Unused Channel List.......................... 100,104,108,112,116,132,136,

--More or (q)uit current module or to abort

140,165

802.11a 4.9 GHz Auto-RF Channel List

Allowed Channel List.........................

Unused Channel List.......................... 1,2,3,4,5,6,7,8,9,10,11,12,

13,14,15,16,17,18,19,20,21,

22,23,24,25,26

DCA Outdoor AP option.......................... Disabled

Radio RF Grouping

802.11a Group Mode............................. AUTO

802.11a Group Update Interval.................. 600 seconds

802.11a Group Leader........................... Cisco_e1:da:a4 (10.161.98.20)

802.11a Group Member......................... Cisco_e1:da:a4 (10.161.98.20)

802.11a Last Run............................... 13 seconds ago

802.11a CleanAir Configuration

Clean Air Solution............................... Disabled

Air Quality Settings:

Air Quality Reporting........................ Enabled

Air Quality Reporting Period (min)........... 15

Air Quality Alarms........................... Enabled

Air Quality Alarm Threshold.................. 35

Interference Device Settings:

Interference Device Reporting................ Enabled

--More or (q)uit current module or to abort

Interference Device Types:

TDD Transmitter.......................... Enabled

Jammer................................... Enabled

Continuous Transmitter................... Enabled

DECT-like Phone.......................... Enabled

Video Camera............................. Enabled

WiFi Inverted............................ Enabled

WiFi Invalid Channel..................... Enabled

SuperAG.................................. Enabled

Canopy................................... Enabled

WiMax Mobile............................. Enabled

WiMax Fixed.............................. Enabled

Interference Device Alarms................... Enabled

Interference Device Types Triggering Alarms:

TDD Transmitter.......................... Disabled

Jammer................................... Enabled

Continuous Transmitter................... Disabled

DECT-like Phone.......................... Disabled

Video Camera............................. Disabled

WiFi Inverted............................ Enabled

WiFi Invalid Channel..................... Enabled

SuperAG.................................. Disabled

Canopy................................... Disabled

--More or (q)uit current module or to abort

WiMax Mobile............................. Disabled

WiMax Fixed.............................. Disabled

Additional Clean Air Settings:

CleanAir Event-driven RRM State.............. Disabled

CleanAir Driven RRM Sensitivity.............. Medium

CleanAir Persistent Devices state............ Disabled

802.11a CleanAir AirQuality Summary

AQ = Air Quality

DFS = Dynamic Frequency Selection

AP Name Channel Avg AQ Min AQ Interferers DFS

------------------ ------- ------ ------ ----------- ---

Press Enter to continue or to abort

802.11b Configuration

802.11b Network.................................. Enabled

11gSupport....................................... Enabled

11nSupport....................................... Enabled

802.11b/g Operational Rates

802.11b/g 1M Rate............................ Mandatory

802.11b/g 2M Rate............................ Mandatory

802.11b/g 5.5M Rate.......................... Mandatory

802.11b/g 11M Rate........................... Mandatory

802.11g 6M Rate.............................. Supported

802.11g 9M Rate.............................. Supported

802.11g 12M Rate............................. Supported

802.11g 18M Rate............................. Supported

802.11g 24M Rate............................. Supported

802.11g 36M Rate............................. Supported

802.11g 48M Rate............................. Supported

802.11g 54M Rate............................. Supported

802.11n MCS Settings:

MCS 0........................................ Supported

MCS 1........................................ Supported

MCS 2........................................ Supported

MCS 3........................................ Supported

MCS 4........................................ Supported

--More or (q)uit current module or to abort

MCS 5........................................ Supported

MCS 6........................................ Supported

MCS 7........................................ Supported

MCS 8........................................ Supported

MCS 9........................................ Supported

MCS 10....................................... Supported

MCS 11....................................... Supported

MCS 12....................................... Supported

MCS 13....................................... Supported

MCS 14....................................... Supported

MCS 15....................................... Supported

802.11n Status:

A-MPDU Tx:

Priority 0............................... Enabled

Priority 1............................... Disabled

Priority 2............................... Disabled

Priority 3............................... Disabled

Priority 4............................... Enabled

Priority 5............................... Enabled

Priority 6............................... Disabled

Priority 7............................... Disabled

A-MSDU Tx:

Priority 0............................... Enabled

--More or (q)uit current module or to abort

Priority 1............................... Enabled

Priority 2............................... Enabled

Priority 3............................... Enabled

Priority 4............................... Enabled

Priority 5............................... Enabled

Priority 6............................... Disabled

Priority 7............................... Disabled

Rifs Rx ..................................... Enabled

Guard Interval .............................. Any

Beacon Interval.................................. 100

CF Pollable mode................................. Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 1

Default Tx Power Level........................... 0

DTPC Status..................................... Enabled

Call Admission Limit ........................... 105

G711 CU Quantum ................................. 15

ED Threshold..................................... -50

Fragmentation Threshold.......................... 2346

PBCC mandatory................................... Disabled

RTS Threshold.................................... 2347

--More or (q)uit current module or to abort

Short Preamble mandatory......................... Enabled

Short Retry Limit................................ 7

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

Faster Carrier Tracking Loop..................... Disabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

Call Admission Control (CAC) configuration

Voice AC - Admission control (ACM)............ Disabled

Voice Stream-Size............................. 84000

Voice Max-Streams............................. 2

Voice max RF bandwidth........................ 75

Voice reserved roaming bandwidth.............. 6

Voice CAC Method.............................. Load-Based

Voice tspec inactivity timeout................ Disabled

CAC SIP-Voice configuration

SIP based CAC ................................ Disabled

SIP Codec Type ............................... CODEC_TYPE_G711

SIP call bandwidth: .......................... 64

SIP call bandwidth sample-size ............... 20

Video AC - Admission control (ACM)............ Disabled

--More or (q)uit current module or to abort

Video max RF bandwidth........................ Infinite

Video reserved roaming bandwidth.............. 0

Best-effort AC - Admission control (ACM)...... Disabled

Background AC - Admission control (ACM)....... Disabled

Press Enter to continue or to abort

802.11b Advanced Configuration

AP Name MAC Address Admin State Operation Stat

Channel TxPower

-------------------------------- ------------------ ------------ --------------

---------- --------

APe8b7.48ac.1050 e8:ba:70:93:81:60 ENABLED DOWN

1* 1(*)

Press Enter to continue or to abort

802.11b Airewave Director Configuration

RF Event and Performance Logging

Channel Update Logging......................... Off

Coverage Profile Logging....................... Off

Foreign Profile Logging........................ Off

Load Profile Logging........................... Off

Noise Profile Logging.......................... Off

Performance Profile Logging.................... Off

Transmit Power Update Logging.................. Off

Default 802.11b AP performance profiles

802.11b Global Interference threshold.......... 10 %

802.11b Global noise threshold................. -70 dBm

802.11b Global RF utilization threshold........ 80 %

802.11b Global throughput threshold............ 1000000 bps

802.11b Global clients threshold............... 12 clients

Default 802.11b AP monitoring

802.11b Monitor Mode........................... enable

802.11b Monitor Channels....................... Country channels

802.11b RRM Neighbor Discovery Type............ Transparent

802.11b AP Coverage Interval................... 180 seconds

802.11b AP Load Interval....................... 60 seconds

802.11b AP Noise Interval...................... 180 seconds

--More or (q)uit current module or to abort

802.11b AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

Transmit Power Assignment Mode................. AUTO

Transmit Power Update Interval................. 600 seconds

Transmit Power Threshold....................... -70 dBm

Transmit Power Neighbor Count.................. 3 APs

Min Transmit Power............................. -10 dBm

Max Transmit Power............................. 30 dBm

Transmit Power Update Contribution............. SNI..

Transmit Power Assignment Leader............... Cisco_e1:da:a4 (10.161.98.20)

Last Run....................................... 14 seconds ago

Coverage Hole Detection

802.11b Coverage Hole Detection Mode........... Enabled

802.11b Coverage Voice Packet Count............ 100 packets

802.11b Coverage Voice Packet Percentage....... 50%

802.11b Coverage Voice RSSI Threshold.......... -80 dBm

802.11b Coverage Data Packet Count............. 50 packets

802.11b Coverage Data Packet Percentage........ 50%

802.11b Coverage Data RSSI Threshold........... -80 dBm

802.11b Global coverage exception level........ 25 %

802.11b Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

Channel Assignment Mode........................ AUTO

--More or (q)uit current module or to abort

Channel Update Interval........................ 600 seconds

Anchor time (Hour of the day).................. 0

Channel Update Contribution.................... SNI..

CleanAir Event-driven RRM option............... Disabled

CleanAir Event-driven RRM sensitivity.......... Medium

Channel Assignment Leader...................... Cisco_e1:da:a4 (10.161.98.20)

Last Run....................................... 14 seconds ago

DCA Sensitivity Level: ...................... MEDIUM (10 dB)

DCA Minimum Energy Limit....................... -95 dBm

Channel Energy Levels

Minimum...................................... unknown

Average...................................... unknown

Maximum...................................... unknown

Channel Dwell Times

Minimum...................................... unknown

Average...................................... unknown

Maximum...................................... unknown

802.11b Auto-RF Allowed Channel List........... 1,6,11

Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10

Radio RF Grouping

802.11b Group Mode............................. AUTO

802.11b Group Update Interval.................. 600 seconds

--More or (q)uit current module or to abort

802.11b Group Leader........................... Cisco_e1:da:a4 (10.161.98.20)

802.11b Group Member......................... Cisco_e1:da:a4 (10.161.98.20)

802.11b Last Run............................... 14 seconds ago

802.11a CleanAir Configuration

Clean Air Solution............................... Enabled

Air Quality Settings:

Air Quality Reporting........................ Enabled

Air Quality Reporting Period (min)........... 15

Air Quality Alarms........................... Enabled

Air Quality Alarm Threshold.................. 35

Interference Device Settings:

Interference Device Reporting................ Enabled

Interference Device Types:

Bluetooth Link........................... Enabled

Microwave Oven........................... Enabled

802.11 FH................................ Enabled

Bluetooth Discovery...................... Enabled

TDD Transmitter.......................... Enabled

Jammer................................... Enabled

Continuous Transmitter................... Enabled

DECT-like Phone.......................... Enabled

Video Camera............................. Enabled

--More or (q)uit current module or to abort

802.15.4................................. Enabled

WiFi Inverted............................ Enabled

WiFi Invalid Channel..................... Enabled

SuperAG.................................. Enabled

Canopy................................... Enabled

Microsoft Device......................... Enabled

WiMax Mobile............................. Enabled

WiMax Fixed.............................. Enabled

Interference Device Alarms................... Enabled

Interference Device Types Triggering Alarms:

Bluetooth Link........................... Disabled

Microwave Oven........................... Disabled

802.11 FH................................ Disabled

Bluetooth Discovery...................... Disabled

TDD Transmitter.......................... Disabled

Jammer................................... Enabled

Continuous Transmitter................... Disabled

DECT-like Phone.......................... Disabled

Video Camera............................. Disabled

802.15.4................................. Disabled

WiFi Inverted............................ Enabled

WiFi Invalid Channel..................... Enabled

SuperAG.................................. Disabled

--More or (q)uit current module or to abort

Canopy................................... Disabled

Microsoft Device......................... Disabled

WiMax Mobile............................. Disabled

WiMax Fixed.............................. Disabled

Additional Clean Air Settings:

CleanAir Event-driven RRM State.............. Disabled

CleanAir Driven RRM Sensitivity.............. Medium

CleanAir Persistent Devices state............ Disabled

802.11a CleanAir AirQuality Summary

AQ = Air Quality

DFS = Dynamic Frequency Selection

AP Name Channel Avg AQ Min AQ Interferers DFS

------------------ ------- ------ ------ ----------- ---

Press Enter to continue or to abort

Mobility Configuration

Symmetric Mobility Tunneling (current) .......... Enabled

Symmetric Mobility Tunneling (after reboot) ..... Enabled

Mobility Protocol Port........................... 16666

Default Mobility Domain.......................... e2e

Multicast Mode .................................. Disabled

Mobility Domain ID for 802.11r................... 0x937a

Mobility Keepalive Interval...................... 10

Mobility Keepalive Count......................... 3

Mobility Group Members Configured................ 1

Mobility Control Message DSCP Value.............. 0

Controllers configured in the Mobility Group

MAC Address IP Address Group Name Multicas

IP Status

d0:c2:82:e1:da:a0 10.161.98.20 e2e 0.0.0.0

Up

Press Enter to continue or to abort

Mobility Foreign Map Configuration

WLAN ID Foreign Mac Address Interface

------- ------------------- ---------

Press Enter to continue or to abort

Advanced Configuration

Probe request filtering.......................... Enabled

Probes fwd to controller per client per radio.... 2

Probe request rate-limiting interval............. 500 msec

Aggregate Probe request interval................. 500 msec

EAP-Identity-Request Timeout (seconds)........... 30

EAP-Identity-Request Max Retries................. 2

EAP Key-Index for Dynamic WEP.................... 0

EAP Max-Login Ignore Identity Response........... enable

EAP-Request Timeout (seconds).................... 30

EAP-Request Max Retries.......................... 2

EAPOL-Key Timeout (milliseconds)................. 1000

EAPOL-Key Max Retries............................ 2

EAP-Broadcast Key Interval....................... 3600

dot11-padding.................................... Disabled

Press Enter to continue or to abort

Location Configuration

RFID Tag data Collection......................... Enabled

RFID timeout.................................... 1200 seconds

RFID mobility.................................... Oui:00:14:7e : Vendor:pango

tate:Disabled

Press Enter to continue or to abort

Interface Configuration

Interface Name................................... management

MAC Address...................................... d0:c2:82:e1:da:a0

IP Address....................................... 10.161.98.20

IP Netmask....................................... 255.255.255.0

IP Gateway....................................... 10.161.98.1

External NAT IP State............................ Disabled

External NAT IP Address.......................... 0.0.0.0

VLAN............................................. untagged

Quarantine-vlan.................................. 0

Active Physical Port............................. 1

Primary Physical Port............................ 1

Backup Physical Port............................. Unconfigured

Primary DHCP Server.............................. 10.161.98.20

Secondary DHCP Server............................ Unconfigured

DHCP Option 82................................... Disabled

ACL.............................................. Unconfigured

AP Manager....................................... Yes

Guest Interface.................................. No

L2 Multicast..................................... Disabled

Interface Name................................... virtual

MAC Address...................................... d0:c2:82:e1:da:a0

IP Address....................................... 1.1.1.1

DHCP Option 82................................... Disabled

Virtual DNS Host Name............................ Disabled

AP Manager....................................... No

Guest Interface.................................. No

Press Enter to continue or to abort

Interface Group Configuration

Press Enter to continue or to abort

WLAN Configuration

WLAN Identifier.................................. 1

Profile Name..................................... E2E

Network Name (SSID).............................. e2e50

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

Radius-NAC State............................... Disabled

SNMP-NAC State................................. Disabled

Quarantine VLAN................................ 0

Maximum number of Associated Clients............. 0

Number of Active Clients......................... 0

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

Multicast Interface.............................. Not Configured

--More or (q)uit current module or to abort

WLAN ACL......................................... unconfigured

DHCP Server...................................... Default

DHCP Address Assignment Required................. Disabled

Static IP client tunneling....................... Disabled

Quality of Service............................... Silver (best effort)

Scan Defer Priority.............................. 4,5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Allowed

WMM UAPSD Compliant Client Support............... Disabled

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Passive Client Feature........................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... All

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

Authentication................................ 10.161.96.50 1812

--More or (q)uit current module or to abort

Accounting.................................... Global Servers

Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

802.11 Authentication:........................ Open System

Static WEP Keys............................... Disabled

802.1X........................................ Disabled

Wi-Fi Protected Access (WPA/WPA2)............. Enabled

WPA (SSN IE)............................... Disabled

WPA2 (RSN IE).............................. Enabled

TKIP Cipher............................. Disabled

AES Cipher.............................. Enabled

Auth Key Managem

nt

802.1x.................................. Enabled

PSK..................................... Disabled

CCKM.................................... Disabled

FT(802.11r)............................. Disabled

FT-PSK(802.11r)......................... Disabled

FT Reassociation Timeout......................... 20

FT Over-The-Air mode............................. Enabled

FT Over-The-Ds mode.............................. Enabled

CCKM tsf Tolerance............................... 1000

--More or (q)uit current module or to abort

CKIP ......................................... Disabled

Web Based Authentication...................... Disabled

Web-Passthrough............................... Disabled

Conditional Web Redirect...................... Disabled

Splash-Page Web Redirect...................... Disabled

Auto Anchor................................... Disabled

H-REAP Local Switching........................ Disabled

H-REAP Local Authentication................... Disabled

H-REAP Learn IP Address....................... Enabled

Client MFP.................................... Optional

Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Roamed Call Re-Anchor Policy..................... Disabled

SIP CAC Fail Send-486-Busy Policy................ Enabled

SIP CAC Fail Send Dis-Association Policy......... Disabled

Band Select...................................... Disabled

Load Balancing................................... Disabled

Mobility Anchor List

WLAN ID IP Address Status

------- --------------- ------

Press Enter to continue or to abort

WLAN Configuration

WLAN Identifier.................................. 2

Profile Name..................................... TESTING

Network Name (SSID).............................. TESTING

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

Radius-NAC State............................... Disabled

SNMP-NAC State................................. Disabled

Quarantine VLAN................................ 0

Maximum number of Associated Clients............. 0

Number of Active Clients......................... 0

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

Multicast Interface.............................. Not Configured

--More or (q)uit current module or to abort

WLAN ACL......................................... unconfigured

DHCP Server...................................... Default

DHCP Address Assignment Required................. Disabled

Static IP client tunneling....................... Disabled

Quality of Service............................... Silver (best effort)

Scan Defer Priority.............................. 4,5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Allowed

WMM UAPSD Compliant Client Support............... Disabled

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Passive Client Feature........................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... All

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

Authentication................................ Global Servers

--More or (q)uit current module or to abort

Accounting.................................... Global Servers

Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

802.11 Authentication:........................ Open System

Static WEP Keys............................... Disabled

802.1X........................................ Disabled

Wi-Fi Protected Access (WPA/WPA2)............. Disabled

CKIP ......................................... Disabled

Web Based Authentication...................... Disabled

Web-Passthrough............................... Disabled

Conditional Web Redirect...................... Disabled

Splash-Page Web Redirect...................... Disabled

Auto Anchor................................... Disabled

H-REAP Local Switching........................ Disabled

H-REAP Local Authentication................... Disabled

H-REAP Learn IP Address....................... Enabled

Client MFP.................................... Optional but inactive (WPA2 n

t configured)

Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Roamed Call Re-Anchor Policy..................... Disabled

SIP CAC Fail Send-486-Busy Policy................ Enabled

--More or (q)uit current module or to abort

SIP CAC Fail Send Dis-Association Policy......... Disabled

Band Select...................................... Disabled

Load Balancing................................... Disabled

Mobility Anchor List

WLAN ID IP Address Status

------- --------------- ------

Press Enter to continue or to abort

ACL Configuration

Press Enter to continue or to abort

CPU ACL Configuration

CPU Acl Name................................ NOT CONFIGURED

Wireless Traffic............................ Disabled

Wired Traffic............................... Disabled

Press Enter to continue or to abort

RADIUS Configuration

Vendor Id Backward Compatibility................. Disabled

Call Station Id Case............................. lower

Call Station Id Type............................. IP Address

Aggressive Failover.............................. Enabled

Keywrap.......................................... Disabled

Fallback Test:

Test Mode.................................... Off

Probe User Name.............................. cisco-probe

Interval (in seconds)........................ 300

MAC Delimiter for Authentication Messages........ hyphen

MAC Delimiter for Accounting Messages............ hyphen

Authentication Servers

Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/

hase1/Group/Lifetime/Auth/Encr

--- ---- ---------------- ------ -------- ---- ------- -----------------

------------------------------

1 NM 10.161.96.50 1812 Enabled 2 Enabled Disabled - none/

nknown/group-0/0 none/none

2 NM 10.161.96.98 1812 Enabled 2 Enabled Disabled - none/

nknown/group-0/0 none/none

Accounting Servers

--More or (q)uit current module or to abort

Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/

hase1/Group/Lifetime/Auth/Encr

--- ---- ---------------- ------ -------- ---- ------- -----------------

------------------------------

Press Enter to continue or to abort

TACACS Configuration

Authentication Servers

Idx Server Address Port State Tout

--- ---------------- ------ -------- ----

Authorization Servers

Idx Server Address Port State Tout

--- ---------------- ------ -------- ----

Accounting Servers

Idx Server Address Port State Tout

--- ---------------- ------ -------- ----

Press Enter to continue or to abort

LDAP Configuration

Press Enter to continue or to abort

Local EAP Configuration

User credentials database search order:

Primary ..................................... Local DB

Timer:

Active timeout .............................. 300

Configured EAP profiles:

EAP Method configuration:

EAP-FAST:

Server key ................................

TTL for the PAC ........................... 10

Anonymous provision allowed ............... Yes

Authority ID .............................. 436973636f0000000000000000000

00

Authority Information ..................... Cisco A-ID

Press Enter to continue or to abort

HREAP Group Summary

HREAP Group Summary: Count: 0

Group Name # Aps

Press Enter to continue or to abort

HREAP Group Detail

Press Enter to continue or to abort

Route Info

Number of Routes................................. 0

Destination Network Netmask Gateway

------------------- ------------------- -------------------

Press Enter to continue or to abort

Qos Queue Length Info

Platinum queue length............................ 100

Gold queue length................................ 75

Silver queue length.............................. 50

Bronze queue length.............................. 25

Press Enter to continue or to abort

Mac Filter Info

Press Enter to continue or to abort

Authorization List

Authorize MIC APs against AAA ................... disabled

Authorize LSC APs against Auth-List ............. disabled

APs Allowed to Join

AP with Manufacturing Installed Certificate.... yes

AP with Self-Signed Certificate................ no

AP with Locally Significant Certificate........ no

Press Enter to continue or to abort

Load Balancing Info

Aggressive Load Balancing........................ per WLAN enabling

Aggressive Load Balancing Window................. 5 clients

Aggressive Load Balancing Denial Count........... 3

Statistics

Total Denied Count............................... 0 clients

Total Denial Sent................................ 0 messages

Exceeded Denial Max Limit Count.................. 0 times

None 5G Candidate Count.......................... 0 times

None 2.4G Candidate Count........................ 0 times

Press Enter to continue or to abort

DHCP Info

No leases allocated.

DHCP Opt-82 RID Format:

DHCP Proxy Behaviour: disabled

Press Enter to continue or to abort

Exclusion List ConfigurationUnable to retrieve exclusion-list entry

Press Enter to continue or to abort

CDP Configuration

cdp version v2

Press Enter to continue or to abort

Country Channels Configuration

Configured Country............................. CA - Canada

KEY: * = Channel is legal in this country and may be configured manually.

A = Channel is the Auto-RF default in this country.

. = Channel is not legal in this country.

C = Channel has been configured for use by Auto-RF.

x = Channel is available to be configured for use by Auto-RF.

(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

802.11bg :

Channels : 1 1 1 1 1

: 1 2 3 4 5 6 7 8 9 0 1 2 3 4

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

CA (-A ,-ABN ): A * * * * A * * * * A . . .

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6

: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

CA (-A ,-ABN ): . A . A . A . A A A A A * * * * * . . . * * * A A A A *

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

--More or (q)uit current module or to abort

4.9GHz 802.11a :

Channels : 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2

: 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

CA (-A ,-ABN ): * * * * * * * * * * * * * * * * * * * A * * * * * A

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

Press Enter to continue or to abort

WPS Configuration Summary

Auto-Immune

Auto-Immune.................................... Disabled

Client Exclusion Policy

Excessive 802.11-association failures.......... Enabled

Excessive 802.11-authentication failures....... Enabled

Excessive 802.1x-authentication................ Enabled

IP-theft....................................... Enabled

Excessive Web authentication failure........... Enabled

Signature Policy

Signature Processing........................... Enabled

Press Enter to continue or to abort

Custom Web Configuration

Radius Authentication Method..................... PAP

Cisco Logo....................................... Enabled

CustomLogo....................................... None

Custom Title..................................... None

Custom Message................................... None

Custom Redirect URL.............................. None

Web Authentication Type.......................... Internal Default

External Web Authentication URL.................. None

Configuration Per Profile:

Press Enter to continue or to abort

Core dump Configuration

Core Dump is disabled

Press Enter to continue or to abort

Rogue AP Configuration

Rogue on wire Auto-Contain....................... Disabled

Rogue using our SSID Auto-Contain................ Disabled

Valid client on rogue AP Auto-Contain............ Disabled

Rogue AP timeout................................. 1200

Monitor Mode Report Interval..................... 10

MAC Address Classification # APs # Clients Last Heard

----------------- ------------------ ----- --------- -----------------------

Adhoc Rogue Configuration

Detect and report Ad-Hoc Networks................ Enabled

Auto-Contain Ad-Hoc Networks..................... Disabled

Client MAC Address Adhoc BSSID State # APs Last Heard

------------------ ------------------ ----------------- ------ ------------

----------

Rogue Client Configuration

Validate rogue clients against AAA............... Disabled

--More or (q)uit current module or to abort

MAC Address State # APs Last Heard

----------------- ------------------ ----- -----------------------

Ignore List Configuration

MAC Address

-----------------

Rogue Rule Configuration

Priority Rule Name State Type Match Hit Count

-------- ----------------------- -------- ------------- ----- ---------

Press Enter to continue or to abort

Media-Stream Configuration

Multicast-direct State........................... disable

Allowed WLANs....................................

Stream Name Start IP End IP Operation Status

------------- -------------- -------------- ----------------

URL..............................................

E-mail...........................................

Phone............................................

Note.............................................

State............................................ disable

2.4G Band Media-Stream Configuration

Multicast-direct................................. Enabled

Best Effort...................................... Disabled

--More-- or (q)uit

Video Re-Direct.................................. Enabled

Max Allowed Streams Per Radio.................... Auto

Max Allowed Streams Per Client................... Auto

Max Video Bandwidth.............................. 0

Max Voice Bandwidth.............................. 75

Max Media Bandwidth.............................. 85

Min PHY Rate..................................... 6000

Max Retry Percentage............................. 80

5G Band Media-Stream Configuration

Multicast-direct................................. Enabled

Best Effort...................................... Disabled

Video Re-Direct.................................. Enabled

Max Allowed Streams Per Radio.................... Auto

Max Allowed Streams Per Client................... Auto

Max Video Bandwidth.............................. 0

Max Voice Bandwidth.............................. 75

Max Media Bandwidth.............................. 85

Min PHY Rate..................................... 6000

Max Retry Percentage............................. 80

--More-- or (q)uit

Number of Clients................................ 0

Client Mac Stream Name Stream Type Radio WLAN QoS Status

----------------- ----------- ----------- ---- ---- ------ -------

(Cisco Controller) show>

Leo Laohoo · ‎02-01-2012

Can you console into the WAP and reboot it? Please post the full output of the entire bootup process.

HEATH FREEL · ‎02-01-2012

Here it is

WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)

Board Revision 0.0 (SN: PSJ154208DT, Type: AIR-CT2504-K9) (P)

Verifying boot loader integrity... OK.

OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)

CPU Cores: 4

DRAM: 1024 MB

Flash: 32 MB

Clearing DRAM........ done

Network: octeth0', octeth1, octeth2, octeth3

' - Active interface

E - Environment MAC address override

CF Bus 0 (IDE): OK

IDE device 0:

- Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C341105448A12d5BDEYK

- Type: Hard Disk

- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)

Press now to access the Boot Menu...

Loading primary image (7.0.116.0)

100%

31535298 bytes read

Launching...

Launching images...

init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary

starting pid 672, tty '': '/etc/init.d/rcS'

type = block

dump-device = 254:4

disrupt

level = header

compress = none

ifconfig: SIOCGIFFLAGS: No such device

Detecting Hardware ...

Installing ether-pow driver - 0x6008

starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'

Cryptographic library self-test....passed!

XML config selected

Validating XML configuration

octeon_device_init: found 1 DPs

/dev/fpga: No such device or address

readCPUConfigData: cardid 0x6060001

Cisco is a trademark of Cisco Systems, Inc.

Cisco AireOS Version 7.0.116.0

Firmware Version PIC 16.0

Initializing OS Services: ok

Initializing Serial Services: ok

Initializing Network Services: ok

Initializing Licensing Services: ok

Starting ARP Services: ok

Starting Trap Manager: ok

Starting Network Interface Management Services: ok

Starting System Services: ok

Starting Fastpath Hardware Acceleration: ok

Starting Fastpath Console redirect : ok

Starting Fastpath DP Heartbeat : ok

Fastpath CPU00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok

Fastpath CPU00: Initializing last packet received queue. Num of cores(2)

Fastpath CPU00: Init MBUF size: 1856, Subsequent MBUF size: 2040

Fastpath CPU00: Core 0 Initialization: ok

Fastpath CPU01: Core 1 Initialization: ok

Fastpath CPU00: Initializing Timer...

Fastpath CPU00: Initializing Timer...done.

Starting Switching Services: ok

Starting QoS Services: ok

Starting Policy Manager: ok

Starting Data Transport Link Layer: ok

Starting Access Control List Services: ok

Starting System Interfaces: ok

Starting Client Troubleshooting Service: ok

Starting Management Frame Protection: ok

Starting Certificate Database: ok

Starting VPN Services: ok

Starting Licensing Services: ok

Starting LWAPP: ok

Starting CAPWAP: ok

Starting LOCP: ok

Starting Security Services: ok

Starting Policy Manager: ok

Starting Authentication Engine: ok

Starting Mobility Management: ok

Starting Virtual AP Services: ok

Starting AireWave Director: ok

Starting Network Time Services: ok

Starting Cisco Discovery Protocol: ok

Starting Broadcast Services: ok

Starting Logging Services: ok

Starting DHCP Server: ok

Starting IDS Signature Manager: ok

Starting RFID Tag Tracking: ok

Starting Power Supply and Fan Status Monitoring Service: ok

Starting Mesh Services: ok

Starting TSM: ok

Starting CIDS Services: ok

Starting Ethernet-over-IP: ok

Starting DTLS server: enabled in CAPWAP

Starting CleanAir: ok

Starting WIPS: ok

Starting SSHPM LSC PROV LIST: ok

Starting RRC Services: ok

Starting FMC HS: ok

Starting Management Services:

Web Server: ok

CLI: ok

Secure Web: ok

License Agent: ok

(Cisco Controller)

Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)

User:

Leo Laohoo · ‎02-01-2012

Errrr ... I meant your WAP and not the WLC 2504.

HEATH FREEL · ‎02-01-2012

My mistake..... Here you go. Missing the very beginning.

r WRDTR,CLKTR: 0x86000800 0x00000000

r RQDC ,RFDC : 0x80000034 0x00000257

using eeprom values

WRDTR,CLKTR: 0x86000800 0x00000000

RQDC ,RFDC : 0x80000034 0x00000257

ddr init done

Running Normal Memtest...

Passed.

IOS Bootloader - Starting system.

FLASH CHIP: Numonyx P33

Checking for Over Erased blocks

................................................................................ ................................................................................ ................................................................................ ......

Xmodem file system is available.

DDR values used from system serial eeprom.

WRDTR,CLKTR: 0x86000800, 0x00000000

RQDC, RFDC : 0x80000034, 0x00000257

PCIE0: link is up.

PCIE0: VC0 is active

PCIE1: link is NOT up.

Check PCIe signals to radio, re-seat radio.

PCIE1 port 1 not initialized

64bit PCIE devices

PCIEx: initialization done

flashfs[0]: 31 files, 8 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31739904

flashfs[0]: Bytes used: 8313856

flashfs[0]: Bytes available: 23426048

flashfs[0]: flashfs fsck took 9 seconds.

Reading cookie from system serial eeprom...Done

Base Ethernet MAC address: e8:b7:48:ac:10:50

Ethernet speed is 1000 Mb - FULL duplex

Loading "flash:/ap3g1-k9w8-mx.124-23c.JA2/ap3g1-k9w8-mx.124-23c.JA2"...######### ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ #######################################################

File "flash:/ap3g1-k9w8-mx.124-23c.JA2/ap3g1-k9w8-mx.124-23c.JA2" uncompressed a nd installed, entry point: 0x4000

executing...

enet halted

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 13-Apr-11 12:20 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP: Numonyx P33

Checking for Over Erased blocks

................................................................................ ................................................................................ ................................................................................ ......

flashfs[1]: 31 files, 8 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31481856

flashfs[1]: Bytes used: 8313856

flashfs[1]: Bytes available: 23168000

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 1 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 1000 Mb - FULL duplex

Radio0 present 8364B 8000 B8020000 0 B8030000 10

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-CAP3501I-A-K9 (PowerPC460exr) processor (revision A0) with 81910K/4 9152K bytes of memory.

Processor board ID FTX1523E3L1

PowerPC460exr CPU at 666Mhz, revision number 0x18A8

Last reset from power-on

LWAPP image version 7.0.116.0

1 Gigabit Ethernet interface

1 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: E8:B7:48:AC:10:50

Part Number : 73-12175-05

PCA Assembly Number : 800-32268-05

PCA Revision Number : A0

PCB Serial Number : FOC15163XLD

Top Assembly Part Number : 800-32902-01

Top Assembly Serial Number : FTX1523E3L1

Top Revision Number : A0

Product/Model Number : AIR-CAP3501I-A-K9

% Please define a domain-name first.

Press RETURN to get started!

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)

*Mar 1 00:00:09.654: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self t est passed

*Mar 1 00:00:09.666: *** CRASH_LOG = YES

*Mar 1 00:00:09.666: Port 0 is not present

*Mar 1 00:00:09.666: 64bit PCIE devicesSecurity Core found.

Base Ethernet MAC address: E8:B7:48:AC:10:50

*Mar 1 00:00:12.277: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar 1 00:00:13.079: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 0 -Process= "Init", ipl= 0, pid= 3

*Mar 1 00:00:13.127: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar 1 00:00:13.145: status of voice_diag_test from WLC is false

*Mar 1 00:00:14.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth ernet0, changed state to up

*Mar 1 00:00:15.250: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 13-Apr-11 12:20 by prod_rel_team

*Mar 1 00:00:15.250: %SNMP-5-COLDSTART: SNMP agent on host APe8b7.48ac.1050 is undergoing a cold start

*Mar 1 00:10:40.044: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r eset

*Mar 1 00:10:41.044: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio 0, changed state to down

*Mar 1 00:10:52.041: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar 1 00:10:52.252: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar 1 00:10:58.927: status of voice_diag_test from WLC is false

*Mar 1 00:10:58.984: Logging LWAPP message to 255.255.255.255.

*Mar 1 00:10:59.003: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s ource

*Mar 1 00:11:00.003: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power s ource

wmmAC status is FALSE

*Feb 1 21:37:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.161.98.20 peer_port: 5246

*Feb 1 21:37:13.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Feb 1 21:37:13.522: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.161.98.20 peer_port: 5246

*Feb 1 21:37:13.522: %CAPWAP-5-SENDJOIN: sending Join Request to 10.161.98.20

*Feb 1 21:37:13.522: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Feb 1 21:37:13.676: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Feb 1 21:37:13.780: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Feb 1 21:37:13.824: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller Cisco_e1:da:a4

*Feb 1 21:37:13.871: %LWAPP-3-CLIENTEVENTLOG: SSID e2e50 added to the slot[0]

*Feb 1 21:37:13.871: %LWAPP-3-CLIENTEVENTLOG: SSID TESTING added to the slot[0]

*Feb 1 21:37:13.874: %WIDS-5-ENABLED: IDS Signature is loaded and enabled

User Access Verification

Leo Laohoo · ‎02-01-2012

Hey, wait a minute. I've seen this before.

Your 802.11b is disabled on the controller.

Wireless > 802.11b/g/n > Network > General > 802.11b/g Network Status

Or go to Wireless > All Access Points > 802.11b/g/n > WAP of your Choice > Go to the right and you'll see a blue upside-down arrow, hover your cursor over it and choose Configure.

Under Admin Status, make sure it's ENABLE.

HEATH FREEL · ‎02-01-2012

Just checked - enabled on both screens.