- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-22-2022 12:09 AM
Hello everyone,
I have an issue adding Capwap ap's to the controller, It all started when I had to reset my ME ap since it was not transmitting WiFi signal, and after the WiFi issue is resolved and reconfigured the ME ap, I'm not able of adding the Capwap ap's to it,
Note that all ap's are on the same VLAN, and the Capwap ap's are discovered by the controller but not manageable,
Kindly find attached image, it's a screenshot of the ap's list,
Thank you,
Best Regards,
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-24-2022 05:08 PM
So your MainAP is running 8.5.105.0 while the other 2 are running 8.8.111.0 which is why they aren't working and you obviously haven't set up a TFTP server for them to download the software from so they can never fully join.
But your quick fix here is that your MainAP has 8.8.111.0 in the backup partition so all you have to do is switch to the backup image then they'll all be on the same version and should work.
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-22-2022 01:16 AM
- What is the controller model and software version ?
M.
-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-22-2022 01:28 AM
Model: AIR-AP1815I-E-K9
Software version: 8.5.105.0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-22-2022 04:58 AM - edited 11-22-2022 04:59 AM
- Check controller logs when the AP's try to join and post the (capwap)-ap boot process.
M.
M.
-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-24-2022 01:40 AM
Controller Logs
*httpImgDwnldTask1: Nov 24 11:12:55.060: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 11:12:50.020: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*CAPWAP DATA: Nov 24 11:12:29.898: %RRM-3-RRM_LOGMSG: rrmClient.c:1531 RRM LOG: iapp chd client stat , Unable to find AP b4:de:31:9b:7e:20
*Dot1x_NW_MsgTask_0: Nov 24 11:12:06.738: %DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:452 Invalid replay counter from client 4c:dd:31:72:38:d9 - got 00 00 00 00 00 00 00 0c, expected 00 00 00 00 00 00 00 0d
*Dot1x_NW_MsgTask_0: Nov 24 11:12:06.423: %DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:452 Invalid replay counter from client 66:29:ec:98:3a:85 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*httpImgDwnldTask1: Nov 24 11:10:36.314: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 11:10:31.264: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask1: Nov 24 11:08:17.537: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 11:08:12.508: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*CAPWAP DATA: Nov 24 11:07:59.811: %RRM-3-RRM_LOGMSG: rrmClient.c:1531 RRM LOG: iapp chd client stat , Unable to find AP b4:de:31:9b:7e:20
*httpImgDwnldTask1: Nov 24 11:05:58.780: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 11:05:53.751: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask1: Nov 24 11:03:40.044: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 11:03:34.188: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*CAPWAP DATA: Nov 24 11:03:29.758: %RRM-3-RRM_LOGMSG: rrmClient.c:1531 RRM LOG: iapp chd client stat , Unable to find AP b4:de:31:9b:7e:20
*httpImgDwnldTask1: Nov 24 11:01:21.268: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 11:01:16.221: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask1: Nov 24 10:59:02.505: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 10:58:57.464: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask1: Nov 24 10:56:43.741: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 10:56:38.705: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask1: Nov 24 10:54:24.206: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 LabAP: Curl returned error code= 28 , err_string: Timeout was reached
*httpImgDwnldTask0: Nov 24 10:54:19.164: %CAPWAP-3-PRED_ERR3: capwap_ac_img_dwnld.c:1697 HeadOffice: Curl returned error code= 28 , err_string: Timeout was reached
_____________________________________________________
Capwap Boot Process
Kindly find attach Capwap.txt file with the boot process
_____________________________________________________
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-23-2022 12:17 AM - edited 11-23-2022 12:18 AM
Yes we need to see those console logs from the CAPWAP APs from power on.
Also the join stats from the ME WLC.
show ap join stats summary all
show ap join stats detailed <Cisco AP Mac>
and "show sysinfo" and "show ap image all" from the ME.
The APs are not showing IP addresses in the screenshot - just to confirm your DHCP is working and they're getting IP addresses?
8.5.105.0 is very old, lots of known bugs resolved since then - you should be considering an update to 8.5.182.0 or 8.10 latest (wait for 8.10.183.0 - due soon - if you want 8.10).
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-24-2022 01:49 AM - edited 11-24-2022 01:51 AM
(Cisco Controller) >show ap join stats summary all
Number of APs.............................................. 3
Base Mac AP EthernetMac AP Name IP Address Status
a0:93:51:1e:29:e0 a0:93:51:1e:29:e0 HeadOffice 172.16.11.3 Joined
b4:de:31:27:46:80 00:5d:73:79:ee:48 MainAP▒ 172.16.11.2 Joined
b4:de:31:9b:7e:20 b4:de:31:9b:7e:20 LabAP 172.16.11.4 Joined
(Cisco Controller) >show ap join stats detailed a0:93:51:1e:29:e0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 60
- Successful discovery responses sent...................... 60
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Nov 24 11:42:54.656
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 19
- Successful join responses sent........................... 19
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Nov 24 11:43:04.203
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... None
- Reason for error that occurred last...................... Not applicable
- Time at which the last join error occurred............... Not applicable
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : a0:93:51:1e :29:e0 Ip Address : 172.16.11.3
--More-- or (q)uit
(Cisco Controller) >show ap join stats detailed a0:93:51:1e:29:e0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 63
- Successful discovery responses sent...................... 63
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Nov 24 11:45:13.427
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 19
- Successful join responses sent........................... 19
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Nov 24 11:43:04.203
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... None
- Reason for error that occurred last...................... Not applicable
- Time at which the last join error occurred............... Not applicable
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : a0:93:51:1e :29:e0 Ip Address : 172.16.11.3
--More-- or (q)uit
(Cisco Controller) >show ap join stats detailed b4:de:31:9b:7e:20
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 63
- Successful discovery responses sent...................... 63
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Nov 24 11:44:57.928
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 21
- Successful join responses sent........................... 21
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Nov 24 11:45:07.485
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... None
- Reason for error that occurred last...................... Not applicable
- Time at which the last join error occurred............... Not applicable
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : b4:de:31:9b :7e:20 Ip Address : 172.16.11.4
--More-- or (q)uit
(Cisco Controller) >show ap join stats detailed b4:de:31:27:46:80
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 1
- Successful discovery responses sent...................... 1
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Nov 24 01:10:50.097
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 1
- Successful join responses sent........................... 1
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Nov 24 01:10:59.881
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 5
- Successful configuration responses sent.................. 2
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Nov 24 01:11:00.826
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Unknown failure reason
Last join error summary
- Type of error that occurred last......................... None
- Reason for error that occurred last...................... Not applicable
- Time at which the last join error occurred............... Not applicable
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : 00:5d:73:79 :ee:48 Ip Address : 172.16.11.2
--More-- or (q)uit
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.5.105.0
System Name...................................... cisco1815i
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.2489
IP Address....................................... 172.16.11.5
Last Reset....................................... 0: unknown
System Up Time................................... 0 days 10 hrs 36 mins 30 secs
System Timezone Location......................... (GMT +2:00) Jerusalem
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... LB - Lebanon
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
Number of Active Clients......................... 8
--More-- or (q)uit
OUI Classification Failure Count................. 0
Burned-in MAC Address............................ 00:5D:73:79:EE:40
Maximum number of APs supported.................. 50
System Nas-Id....................................
WLC MIC Certificate Types........................ SHA1/SHA2
(Cisco Controller) >show ap image all
Total number of APs.............................. 3
Number of APs
Initiated....................................... 0
Downloading..................................... 0
Predownloading.................................. 0
Completed predownloading........................ 0
Not Supported................................... 0
Failed/Waiting to Predownload................... 0
Predownload Predownload Flexconnect Failure Download
AP Name Primary Image Backup Image Status Version Next Retry Time Retr y Count Predownload Reason Progress
------------------ -------------- -------------- --------------- -------------- ---------------- ---- -------- -------------- -------------------- ----------
MainAP 8.5.105.0 8.8.111.0 None None NA NA NA
LabAP 8.8.111.0 0.0.0.0 None None NA NA NA
HeadOffice 8.8.111.0 0.0.0.0 None None NA NA NA
________________________________________________________
Regards,
B Osman
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-24-2022 05:08 PM
So your MainAP is running 8.5.105.0 while the other 2 are running 8.8.111.0 which is why they aren't working and you obviously haven't set up a TFTP server for them to download the software from so they can never fully join.
But your quick fix here is that your MainAP has 8.8.111.0 in the backup partition so all you have to do is switch to the backup image then they'll all be on the same version and should work.
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-25-2022 04:02 AM
Thanks you,
On the controller I used the following command to restore the backup,
config ap image swap <ap name>
______________________________________
Regards,
B Osman
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-25-2022 04:46 AM
So it's working now?
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-27-2022 05:59 AM
Yes it is working, thanks you!
I will be upgrading the firmware of the access points later
