Virtual WLC High availability (HA)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2018 12:40 AM - edited 07-05-2021 08:40 AM
hello,
i will configure two Virtual WLC on ha
i will need one or two licenses for each controllers ?
what's the type of license needed
thanks
- Labels:
-
Wireless LAN Controller
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2018 12:42 AM - edited 05-29-2018 12:43 AM
you will need license on both vWLC. It will be normal AP license.
HA AP SSO isn't supported on the vWLC. You can have two vWLC doing redundancy with high availability configured on the AP.
Regards
Dont forget to rate helpful posts
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2018 12:50 AM
hello,
thank you for reply
please, after the ha configuration, when i do the modification in the primary vWLC, i will need to repeat the configuration for the second vWLC or his do it automatically by HA
thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2018 12:56 AM
you need to change manually on both WLCs. Config will not sync....
Regards
Dont forget to rate helpful posts
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2018 03:51 AM
Hi,
someone have a documentation of ha configuration with Virtual WLC !?
thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-29-2018 04:04 AM
Here is the example (same should be with vWLC):
https://rscciew.wordpress.com/2014/06/07/n1-high-availability-configuration-on-cisco-2504wlc/
Regards
Dont forget to rate helpful posts
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-30-2018 02:38 AM
hello,
how to delete firmware file from WLC ?
thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-30-2018 02:45 AM
why you want to delete SW from WLC. Normally WLC keep two (primary and backup )Software
Regards
dont forget to rate helpful posts
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-30-2018 02:59 AM
hi,
because i want do an upgrade
when i transfert the new firmware by FTP server, i see the message
01 FTP Failure while storing in flash! (0) rc:-1 |
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-30-2018 03:55 AM
try with TFTP server.
Regards
Dont forget to rate helpful posts
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-04-2018 04:34 AM
hi,
i am trying to configure ha on two vWLC
I followed this link
https://rscciew.wordpress.com/2014/06/07/n1-high-availability-configuration-on-cisco-2504wlc/
when I type this command at the second vWLC level: config redundancy unit secondary
I find this message : "Incorrect usage"
then the vWLC don't know this command
i upgraded the vWLC but the same problem
someone had an idea
thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-10-2025 02:38 PM
Hello,
I am showing the same error message as Hacen after issuing the "config redundancy unit secondary" command. If I tab out after entering config, redundancy is not an option. Any ideas?
Thanks,
Roger
