wisim controller and 5760 for vlan design and mobility groups

[syed baseeruddin]

Hi 

in our one project they are two wisim 1 module in 6500

and one  5760 controller  connected two same lan network 

and 5760 controller is connected two lan network switch 4948 switch

for wisim 1 modules native vlan is compulsary or

we can make controller mgmt ip add for AP registration

=============================================

And for AP groups for Vlan design there are 28th floor the details of AP as shown below

Floor No.	Qty	AP Type
Roof Floor	4	cisco 2602 with External Antenna
28th Floor	7	Cisco 1040 with integrated Antenna
27th Floor	7	Cisco 1040 with integrated Antenna
26th Floor	7	cisco 2602 with External Antenna
25th Floor	7	Cisco 1040 with integrated Antenna
24th Floor	7	Cisco 1040 with integrated Antenna
23rd Floor	7	Cisco 1040 with integrated Antenna
22nd Floor	7	Cisco 1040 with integrated Antenna
21st Floor	7	Cisco 1040 with integrated Antenna
20th Floor	7	Cisco 1040 with integrated Antenna
19th Floor	7	Cisco 1040 with integrated Antenna
18th Floor	7	Cisco 1040 with integrated Antenna
17th Floor	7	Cisco 1040 with integrated Antenna
16th Floor	7	Cisco 1040 with integrated Antenna
15th Floor	7	Cisco 1040 with integrated Antenna
14th Floor	7	Cisco 1040 with integrated Antenna
13th Floor	7	Cisco 1040 with integrated Antenna
12th Floor	7	Cisco 1040 with integrated Antenna
11th Floor	7	Cisco 1040 with integrated Antenna
10th Floor	7	Cisco 1040 with integrated Antenna
9th Floor	7	Cisco 1040 with integrated Antenna
8th Floor	7	Cisco 1040 with integrated Antenna
7th Floor	7	Cisco 1040 with integrated Antenna
6th Floor	7	Cisco 1040 with integrated Antenna
5th Floor	7	Cisco 1040 with integrated Antenna
4th Floor	10	Cisco 1040 with integrated Antenna
3rd Floor	19	Cisco 1040 with integrated Antenna
2nd Floor	18	cisco 2602 with External Antenna
First Floor	17	cisco 2602 with External Antenna
Mezzanine Floor	4	cisco 2602 with External Antenna
Ground Floor	17	cisco 2602 with External Antenna
B1	31	cisco 2602 with External Antenna
B2	11	Cisco 1040 with integrated Antenna
B3	9	Cisco 1040 with integrated Antenna
Total	308

for each Five floor one one AP groups subnet like  192.168.15.x/24

or 

for each floor seperate subnets for AP groups Experts please advice

For mobility groups 

for two wisim 1 module and 5760 controller

As far i known we cannot make mobility groups for wisim 1 and 5760 controller

expert please advice for mobility groups in this topology

[Rasika Nayanajith · Accepted solution]

in our one project they are two wisim 1 module in 6500 and one  5760 controller  connected two same lan network

WiSM-1 only support upto 7.0.x software code. Hence you cannot register 2600 AP onto it. Refer table 2 of below URL

http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

For each Five floor one one AP groups subnet like  192.168.15.x/24 or for each floor seperate subnets for AP groups Experts please advice.

I would put all of these APs in single AP management vlan (/23) rather break it down to floors

As far i known we cannot make mobility groups for wisim 1 and 5760 controller. expert please advice for mobility groups in this topology

Yes, you cannot have this in same mobility group. I would really consider twice before put WiSM-1 into this network. Simply go with 5760 & that make things simple.

HTH

Rasika

*** Pls rate all useful responses ***

[syed baseeruddin]

Thanks Rasika Nayanajith          

Need your advice

1 I will make  two vlan for clients to get ip 

1.for wisim controller

2. 5760 controller

2. In my topology mobility will not work Because of wisim 1 module.

3.Regarding Native vlan in 6500 series switch for wisim module there compulsary native vlan for Registering for Acess points

or 

with out native vlan if we make mgmt vlan in 6500 series switch  for Registering of Acesspoints

[Rasika Nayanajith · Accepted solution]

Hope below documents are useful on this config requirement

http://www.cisco.com/c/en/us/support/docs/interfaces-modules/catalyst-6500-series-7600-series-wireless-services-module-wism/91473-wism-initial-setup.html

http://wirelessccielab.blogspot.com.au/2010/08/112-wireless-services-module-wism-setup.html

HTH

Rasika

[syed baseeruddin]

Thanks Rasika Nayanajith  

[syed baseeruddin]

Hi 

Need ur support for after configuartion for four wireless controller

in core switch 6500 how to configure dhcp server option 43 for these 4 controller for registration APS

and one question 

each wism-a will support 150 Acess points
but in our project there 208 Acess points of 1040