05-27-2022 04:55 PM
Hi,
I have the following problem, I have a 9800L-F WLC, and I want to make a portchannel (LAG) with the fiber interfaces, it configures successfully, but I have no traffic through it. I don't see MAC either through this portchannel.
The WLC is using SFP-SX-MMD interfaces. Does anyone know why it doesn't work???
IOS-XE Version 17.3.5
Solved! Go to Solution.
05-27-2022 06:56 PM - edited 05-27-2022 06:57 PM
I see some case in nexus with SFP and the issue was the auto negotiation, can you manually set the duplex and speed.
05-27-2022 05:17 PM
05-27-2022 05:19 PM
Hi
Can you share the configuration from WLC and the switch it is connected to?
sh run int po X
show int po X status
05-27-2022 05:42 PM
Hi Flavio,
Adjunto información de los equipos, un dato, si el portchannel lo hago con las interfaces de cobre, sube sin problemas y tengo trafico, pero si bajo ese portchannel y levanto el portchannel de las fibras, este levanta, pero no tengo tráfico.
WLC
ILC-WLC-01#
ILC-WLC-01#
ILC-WLC-01#show vlan bri
ILC-WLC-01#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Tw0/0/0, Tw0/0/1, Tw0/0/2
Tw0/0/3
3 mgmt-sonacol active
101 mgmt-infra-net active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
ILC-WLC-01#
ILC-WLC-01#
ILC-WLC-01#
ILC-WLC-01#show ip int bri
ILC-WLC-01#show ip int brief
Interface IP-Address OK? Method Status Protocol
Tw0/0/0 unassigned YES unset administratively down down
Tw0/0/1 unassigned YES unset administratively down down
Tw0/0/2 unassigned YES unset administratively down down
Tw0/0/3 unassigned YES unset administratively down down
Te0/1/0 unassigned YES unset up up
Te0/1/1 unassigned YES unset up up
GigabitEthernet0 unassigned YES NVRAM administratively down down
Port-channel10 unassigned YES unset up up
Port-channel11 unassigned YES unset administratively down down
Vlan1 unassigned YES NVRAM administratively down down
Vlan3 192.168.3.202 YES NVRAM down down
Vlan101 172.20.1.200 YES NVRAM up up
ILC-WLC-01#
ILC-WLC-01#show etherch
ILC-WLC-01#show etherchannel su
ILC-WLC-01#show etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
A - formed by Auto LAG
Number of channel-groups in use: 2
Number of aggregators: 2
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SU) - Te0/1/0(P) Te0/1/1(P)
11 Po11(SD) - Tw0/0/0(D) Tw0/0/1(D)
Tw0/0/2(D) Tw0/0/3(D)
ILC-WLC-01#
ILC-WLC-01#
ILC-WLC-01#show run int po10
Building configuration...
Current configuration : 90 bytes
!
interface Port-channel10
switchport trunk allowed vlan 101
switchport mode trunk
end
ILC-WLC-01#show run int t0/1/0
Building configuration...
Current configuration : 143 bytes
!
interface TenGigabitEthernet0/1/0
switchport trunk allowed vlan 101
switchport mode trunk
negotiation auto
channel-group 10 mode on
end
ILC-WLC-01#show run int t0/1/1
Building configuration...
Current configuration : 143 bytes
!
interface TenGigabitEthernet0/1/1
switchport trunk allowed vlan 101
switchport mode trunk
negotiation auto
channel-group 10 mode on
end
ILC-WLC-01#show mac add
ILC-WLC-01#show mac address-table
VLAN MAC Address Type AgeIdx InPkt Interface
-------------------------------------------------------------
3 0845.d116.4b2b SVI 0 0 Vlan3
101 0845.d116.4b2b SVI 0 0 Vlan101
1 0845.d116.4b2b SVI 0 0 Vlan1
ILC-WLC-01#
Switch
SW-WIFI#show etherchannel su
SW-WIFI#show etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
A - formed by Auto LAG
Number of channel-groups in use: 2
Number of aggregators: 2
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SU) - Gi1/1/1(P) Gi1/1/2(P)
11 Po11(SD) - Gi1/0/1(D) Gi1/0/2(D)
Gi1/0/3(D) Gi1/0/4(D)
SW-WIFI#
SW-WIFI#
SW-WIFI#
SW-WIFI#
SW-WIFI#
SW-WIFI#show int status
Port Name Status Vlan Duplex Speed Type
Gi1/0/1 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/2 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/3 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/4 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/5 WLC-Port-SP notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/6 WLC-Port-RP connected 1 a-full a-1000 10/100/1000BaseTX
Gi1/0/7 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/8 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/9 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/10 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/11 notconnect 1 auto auto 10/100/1000BaseTX
Port Name Status Vlan Duplex Speed Type
Gi1/0/12 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/13 AP-9120AX connected trunk a-full a-1000 10/100/1000BaseTX
Gi1/0/14 AP-1560 connected trunk a-full a-1000 10/100/1000BaseTX
Gi1/0/15 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/16 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/17 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/18 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/19 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/20 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/21 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/22 notconnect 1 auto auto 10/100/1000BaseTX
Gi1/0/23 notconnect 3 auto auto 10/100/1000BaseTX
Port Name Status Vlan Duplex Speed Type
Gi1/0/24 enlace-Stack01 connected trunk a-full a-1000 10/100/1000BaseTX
Gi1/1/1 connected trunk full 1000 1000BaseSX SFP
Gi1/1/2 connected trunk full 1000 1000BaseSX SFP
Gi1/1/3 notconnect 1 auto auto unknown
Gi1/1/4 notconnect 1 auto auto unknown
Po10 connected trunk a-full a-1000 N/A
Po11 WLC-ILC-01 notconnect 1 auto auto N/A
SW-WIFI#
SW-WIFI#show run int g1/1/1
Building configuration...
Current configuration : 124 bytes
!
interface GigabitEthernet1/1/1
switchport trunk allowed vlan 3,101
switchport mode trunk
channel-group 10 mode on
end
SW-WIFI#show run int g1/1/2
Building configuration...
Current configuration : 124 bytes
!
interface GigabitEthernet1/1/2
switchport trunk allowed vlan 3,101
switchport mode trunk
channel-group 10 mode on
end
SW-WIFI#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Gi1/0/13 on 802.1q trunking 101
Gi1/0/14 on 802.1q trunking 101
Gi1/0/24 on 802.1q trunking 1
Po10 on 802.1q trunking 1
Port Vlans allowed on trunk
Gi1/0/13 3,101,104
Gi1/0/14 101
Gi1/0/24 1-4094
Po10 3,101
Port Vlans allowed and active in management domain
Gi1/0/13 3,101,104
Gi1/0/14 101
Gi1/0/24 1,3,101,103-114
Po10 3,101
Port Vlans in spanning tree forwarding state and not pruned
Gi1/0/13 3,101,104
Gi1/0/14 101
Gi1/0/24 1,3,101,103-114
Port Vlans in spanning tree forwarding state and not pruned
Po10 3,101
SW-WIFI#
SW-WIFI#
SW-WIFI#show run in po10
Building configuration...
Current configuration : 92 bytes
!
interface Port-channel10
switchport trunk allowed vlan 3,101
switchport mode trunk
end
SW-WIFI#
SW-WIFI#show mac add
SW-WIFI#
SW-WIFI#
SW-WIFI#
SW-WIFI#show ethercha
SW-WIFI#show etherchannel summ
SW-WIFI#show etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
A - formed by Auto LAG
Number of channel-groups in use: 2
Number of aggregators: 2
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SU) - Gi1/1/1(P) Gi1/1/2(P)
11 Po11(SD) - Gi1/0/1(D) Gi1/0/2(D)
Gi1/0/3(D) Gi1/0/4(D)
SW-WIFI#
SW-WIFI#
05-27-2022 05:54 PM - edited 05-27-2022 05:56 PM
"Adjunto información de los equipos, un dato, si el portchannel lo hago con las interfaces de cobre, sube sin problemas y tengo trafico, pero si bajo ese portchannel y levanto el portchannel de las fibras, este levanta, pero no tengo tráfico."
Are you using the right fiber cable?
Is it GLC-SX-MMD you are using?
You need to use 1000BASE-SX short wavelength;
Also, when you plug the fiber cable on the WLC side, if you look at the end of the cable, do you see any light, red light? Can you confirm?
And can you do the same for the switch? plug the SFP, the cable and check the light?
05-27-2022 06:07 PM
Attach the information:
WLC
ILC-WLC-01#show inventory
NAME: "subslot 0/1 transceiver 0", DESCR: "GE SX"
PID: GLC-SX-MMD , VID: V03 , SN: OPM25060NEZ
NAME: "subslot 0/1 transceiver 1", DESCR: "GE SX"
PID: GLC-SX-MMD , VID: V03 , SN: OPM25090U3X
ILC-WLC-01#show interfaces status
Port Name Status Vlan Duplex Speed Type
Tw0/0/0 disabled 1 full 2500 1000/2.5GBaseTX
Tw0/0/1 disabled 1 full 2500 1000/2.5GBaseTX
Tw0/0/2 disabled 1 full 2500 1000/2.5GBaseTX
Tw0/0/3 disabled 1 full 2500 1000/2.5GBaseTX
Te0/1/0 connected trunk full a-1000 1000BaseSX
Te0/1/1 connected trunk full a-1000 1000BaseSX
Po10 connected trunk full a-1000 unknown media type
Po11 Uplink Switch Wi-F disabled 1 full auto unknown media type
ILC-WLC-01#
Switch
SW-WIFI#show inventory
NAME: "c92xxL Stack", DESCR: "c92xxL Stack"
PID: C9200L-24P-4G , VID: V02 , SN: JAE25320EMF
NAME: "Switch 1", DESCR: "C9200L-24P-4G"
PID: C9200L-24P-4G , VID: V02 , SN: JAE25320EMF
NAME: "Switch 1 - Power Supply A", DESCR: "Switch 1 - Power Supply A"
PID: PWR-C5-600WAC , VID: V02 , SN: ART2520D3ZQ
NAME: "Gi1/1/1", DESCR: "1000BaseSX SFP"
PID: GLC-SX-MMD , VID: V03 , SN: OPM25060NEM
NAME: "Gi1/1/2", DESCR: "1000BaseSX SFP"
PID: GLC-SX-MMD , VID: V03 , SN: OPM25060NF0
SW-WIFI#show interfaces status
Port Name Status Vlan Duplex Speed Type
Port Name Status Vlan Duplex Speed Type
Gi1/0/24 enlace-Stack01 connected trunk a-full a-1000 10/100/1000BaseTX
Gi1/1/1 connected trunk full 1000 1000BaseSX SFP
Gi1/1/2 connected trunk full 1000 1000BaseSX SFP
Gi1/1/3 notconnect 1 auto auto unknown
Gi1/1/4 notconnect 1 auto auto unknown
Po10 connected trunk a-full a-1000 N/A
Po11 WLC-ILC-01 notconnect 1 auto auto N/A
SW-WIFI#
Yes, i hace red light in both fibers.
Regards
05-27-2022 06:22 PM
Te0/1/0 connected trunk full a-1000 1000BaseSX
Te0/1/1 connected trunk full a-1000 1000BaseSX
Po10 connected trunk full a-1000 unknown media type
Gi1/1/1 connected trunk full 1000 1000BaseSX SFP
Gi1/1/2 connected trunk full 1000 1000BaseSX SFP
Po10 connected trunk a-full a-1000 N/A
Something is not good on the WLC side.
05-27-2022 06:34 PM
Yo know wthat appends?? I have a upgrade de IOS, change de config and nothing.
05-27-2022 06:37 PM
Have you tried a different SFP ?
05-27-2022 06:49 PM
I don't have any other SFP's at this time. I will try to get others
05-27-2022 07:00 PM
Wait a second ... What firmware is the 9200 running on?
05-27-2022 07:04 PM
Cisco 9200L-24P-4G-E
Firmware 17.3.3 Amsterdam
Mode install
05-27-2022 07:12 PM
@Daniel Alejandro Castro Henriquez wrote:
Cisco 9200L-24P-4G-E
Firmware 17.3.3 Amsterdam
Mode install
Downgrade to 16.12.4.
NOTE: I am not joking. 17.X.X is a bad release for 9200/9200L. There are a lot of bugs from 9300/9400/9500/9600 version 16.12.X "re-introduced" to 17.X.X.
05-27-2022 07:02 PM
The problem you are thing is that no traffic is passing, correct?
Just for more one test, can you change the Port-channel to Layer 3 and ping ?
WLC
interface Port-channel10
no switchport
ip add 1.1.1.1 255.255.255.0
SW
terface Port-channel10
no switchport
ip add 1.1.1.2 255.255.255.0
05-27-2022 06:18 PM
interface GigabitEthernet1/1/2
switchport trunk allowed vlan 3,101<- allow VLAN 1 also
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide