Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! new cisco 9800 controller
I could not connect new controller with serial number of device password.I tried username and serial number but no luck.admin admin no luck.I have configured vlan 1 Ip address so i can access through web but not login any one can help me ?
Merkai is aware of a known issue where accounts are getting deleted wihout any audit logs and development team is working on it.Has anyone else faced something similar?
I have some problems getting my 2700 access point to join my 9115 ewc running 17.9.3 software. I tried using a C9800-CL on a esxi and the access point got the correct software and joined that controller. FW is open and connectivity to tftp server is...
Resolved! Scheduling a daily Save Job on WLC 9800
Hello,We have a WLC 9800, we need to create a job to save its running config to its startup config daily at midnight to make sure that the daily configuration changes will remain in case the WLC reloads for whatever reason, especially that we forget ...
Resolved! IP Obfuscation for Guest VLAN
Hi Experts - need your advice on following situation. We need to create a GUEST VLAN in our Meraki Setup, and my project manager requesting if we can obfuscate the public IP for Guest users. Is there a possibility with a setup where we have only Mera...
Problems authenticating clients via LDAP authentication for WLAN 802.1. It is not possible to authenticate users directly to the DA via LDAP. The steps of the guide are followed but the integration is not achieved. https://www.cisco.com/c/en/us/supp...
Does Meraki support soft handoff between Wifi calling and cellular networks?
Hi,There are few topic similar to this one, but none of the solutions worked for me. I have 2 x WLC 9800 in Azure with HA in between (without SSO). APs on one of them flaps randomly and what is important - not all APs from site at the same time. Seco...
I simply cant remember if I asked (and it is now turning into kind of an obsession for me ).Have anyone seen their MR46E set in ETSI reg. domain go above 12dbm in transmit power on 2,4 Ghz ?Even with normal 3dbi antennas ? (MA-ANT-B6)It (the MR46E) s...
Resolved! Converting 9124AXE into Autonomous AP
Hello Experts We require to create a wireless p2p bridge as fiber is not feasible by using 2x9124AXE, no ssid brodacast required. This outdoor APs will not be associated with the site WLC. Pls guide on process to convert this catalyst outdoor AP in...
We have a small fleet (8) of HP 1102W Laser Printers which have been running on our network (MX-64 and MR-34) until recently (4-8 weeks ago). These printers get little use now a days so timing is unclear, but none work, while other devices like lapto...
We have an environment of both 1832i and 9105 AXI APs with the 9105 ap being the ewc. After being connected for a while, clients observe the globe icon instead of the wifi one and don’t have internet connection anymore, they have to switch to other s...
I have a lab set up with a C9130-AXI AP joined to a C9800 WLC. I am trying to use NETCONF or RESTCONF to fetch device probes of the wireless network. I can get them just fine using RESTCONF, as long as the device does not have a randomized MAC addr...
in the datasheet for the 9166 series i can see in the first paragraph that these access points can be managed on premise or through the cloud. does this apply to the CW9166I-MR access points from Meraki ? can they be managed by a 9800-CL virtual wire...
Hi, maybe someone know the answer to the following, CoA related, question.I've verified that the AP responds to CoA messages initiated from the local network. However, the actual requirement is to send these messages from the internet, externally. Th...
