Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
2273
Views
0
Helpful
5
Replies

A9K-RSP440-SE + A9K-MPA-20X1GE : State UNKNOWN

knowledgecom
Level 1
Level 1

‎03-26-2018 02:19 AM - edited ‎03-01-2019 03:23 PM

 

Hi guys. 

 

Chassis would be : ASR9010 

Engine :  A9K-RSP440-SE

Line Card :  A9K-MOD80-TR 

 

As seen by the first sh platform A9K-MPA-20X1GE  would have its state as OK and then a few seconds afterwards it turns off and it changes its state to UNKNOWN. Any help in getting this sorted is greatly appreciated. 

 

RP/0/RSP0/CPU0:ios(admin)#RP/0/RSP0/CPU0:Mar 26 04:45:32.581 : obflmgr[76]: %OS-OBFLMGR-3-RECORD_TOO_SHORT : Too short record size:0 for harddiska:/volt_static_data record at offset:256. The file contents might be corrupted. 
LC/0/1/CPU0:Mar 26 04:45:32.924 : lda_server[65]: %PLATFORM-SCC-2-BAD_ID_HW : Failed Identification Test in 0/129/0 [5/0] The module in 0/129/0 in this router may not be a genuineCisco product.  Cisco warranties and support programs onlyapply to genuine Cisco products.  If Cisco determines thatyour insertion of non-Cisco SPA cards or other modules into aCisco product is the cause of a support issue, Cisco maydeny support under your warranty or under a Cisco supportprogram such as SmartNet.   

RP/0/RSP0/CPU0:ios(admin)#sh platform
Sat Mar 26 04:45:48.455 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        FAN TRAY                  READY            
0/FT1/SP        FAN TRAY                  READY            
0/1/CPU0        A9K-MOD80-TR              IOS XR RUN       PWR,NSHUT,MON
0/1/0           A9K-MPA-20X1GE            OK               PWR,NSHUT,MON
0/PM0/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM1/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM2/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM3/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM4/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM5/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#LC/0/1/CPU0:Mar 26 04:46:02.940 : lda_server[65]: %PLATFORM-LDA-4-MPA_OIR_QUICK_BACK_TO_BACK_ERROR : OIR operation was performed on MPA in bay:0 while the system is initializing. Recommend waiting for two minutes after EP initialized. 
LC/0/1/CPU0:Mar 26 04:46:03.058 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/19, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.058 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/18, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/17, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/16, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/15, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/14, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/13, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/12, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.059 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/11, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.060 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/9, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.060 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/10, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.060 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/8, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.060 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/7, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.060 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/6, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.060 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/5, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.061 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/4, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.061 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/3, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.061 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/2, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.061 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/1, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.061 : ifmgr[201]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/1/0/0, changed state to Down 
LC/0/1/CPU0:Mar 26 04:46:03.971 : lda_server[65]: %PLATFORM-LDA-3-MPA_BAY_SW_ERROR : Unable to initialize MPA in bay: 0, Module has been shutdown due to identify test failure (0x00000000 - No error)  : pkg/bin/lda_server : (PID=45088) :  -Traceback= 4e95859c 4bf10ed0 4bf10fdc 4c72c28c 4c72a1f4 4ba73a44 4ba71554 4c729ddc 4bada400

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh platform
Sat Mar 26 04:46:18.664 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        FAN TRAY                  READY            
0/FT1/SP        FAN TRAY                  READY            
0/1/CPU0        A9K-MOD80-TR              IOS XR RUN       PWR,NSHUT,MON
0/1/0           A9K-MPA-20X1GE            UNKNOWN          PWR,NSHUT,MON
0/PM0/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM1/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM2/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM3/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM4/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PM5/SP        A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#

RP/0/RSP0/CPU0:ios(admin)#sh hw-module fpd location all 
Sat Mar 26 04:50:20.316 UTC

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/RSP0/CPU0  A9K-RSP440-SE              1.0   lc   cbc     0      16.116    No 
                                              lc   fpga2   0       1.09     No 
                                              lc   fpga1   0       0.11     No 
                                              lc   fpga3   0       4.09     No 
                                              lc   rommon  0       0.75     No 
--------------------------------------------------------------------------------
0/FT0/SP     ASR-9010-FAN               1.0   ft   cbc     7       4.02     No 
--------------------------------------------------------------------------------
0/FT1/SP     ASR-9010-FAN               1.0   ft   cbc     8       4.02     No 
--------------------------------------------------------------------------------
0/1/CPU0     A9K-MOD80-TR               1.0   lc   cbc     0      20.118    No 
                                              lc   fpga2   0       1.04     No 
                                              lc   fpga4   0       1.05     No 
                                              lc   rommon  0       2.00     No 
--------------------------------------------------------------------------------
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh env all
Sat Mar 26 04:53:41.983 UTC

Temperature Information
---------------------------------------------

R/S/I   Modules Sensor                  (deg C)

0/1/*
        host    Inlet0                  23.8
        host    Hotspot0                37.5
                              


0/RSP0/*
        host    Inlet0                  21.0
        host    Hotspot0                26.3
                              





0/FT0/*
        host    Inlet0                  19.3
        host    Hotspot0                20.1
                              
0/FT1/*
        host    Inlet0                  19.5
        host    Hotspot0                21.7
                              








Voltage Information
---------------------------------------------

R/S/I   Modules Sensor                   (mV)   Margin

0/1/*
        host    VP3P3_CAN                3302   n/a
        host    VP3.3V_CAN_DB            3288   n/a
        host    VP1P0_SAC_CORE            999   n/a
        host    VP1P0_SAC_VDDA           1000   n/a
        host    VP1P0_SAC_VDDD           1000   n/a
        host    VP1P2_SAC_VDDT           1200   n/a
        host    VP1P8_SAC_VDDR           1800   n/a
        host    VP1P0_LAN                1000   n/a
        host    VP1P0_SKT2_CORE          1000   n/a
        host    VP1P0_SKT2_IO             999   n/a
        host    VP1P5_SKT2_IO            1500   n/a
        host    VP2P5_SKT2_IO            2499   n/a
        host    VP1P0_CPU_CORE           1000   n/a
        host    VP1P0_CPU_PLAT           1000   n/a
        host    VTT_0P75_CPU              750   n/a
        host    VP2P5                    2499   n/a
        host    VP3P3                    3300   n/a
        host    VP1P2                    1199   n/a
        host    VP1P5                    1500   n/a
        host    VP1P8                    1800   n/a
        host    VP5P0                    4999   n/a
        host    VP7P0                    7000   n/a
        host    VP3P3_ZL_VDD             3300   n/a
        host    1.0_N0_CORE_DB           1049   n/a
        host    1.5_N0_IO_DB             1500   n/a
        host    0.75_N0_VTT_DB            752   n/a
        host    0.9_T01_CORE_DB           900   n/a
        host    1.8_N01_IO_DB            1800   n/a
        host    VP1P0_SKT0_CORE           999   n/a
        host    VP1P0_SKT0_IO             999   n/a
        host    VP1P5_SKT0_IO            1500   n/a
        host    VP2P5_SKT0_IO            2499   n/a
        host    VP1P8_ZL_VCORE           1800   n/a
        host    VP1P0_N2_CORE_DB         1049   n/a
        host    VP1P5_N2_IO_DB           1500   n/a
        host    VP0P75_N2_VTT_DB          752   n/a
        host    VP1P8_N23_IO_DB          1800   n/a
        host    VP5P0_DB                 5000   n/a
        host    VP7P0_DB                 6999   n/a
        host    VP3P3_DB                 3300   n/a
        host    VP2P5_DB                 2500   n/a
        host    VP1P2_STARKAD            1197   n/a
        host    VP1P0_PEX_1              1001   n/a
        host    VP1P0_PEX_2               999   n/a
        host    VP1P2_LDO_LANCER         1198   n/a
        host    VP1P2_RAGNAR_CORE_DB     1199   n/a
        host    VP1P5_RAGNAR_IO_DB       1500   n/a
        host    VP1P8_RAGNAR_IO_DB       1799   n/a
        host    0.9_T23_CORE_DB           900   n/a
        host    VP2P5_N01_IO_DB          2499   n/a
        host    VP2P5_N23_IO_DB          2500   n/a



0/RSP0/*
        host    VP3P3_CAN                3299   n/a
        host    VP2P5                    2500   n/a
        host    VP3P3                    3300   n/a
        host    VP1P2                    1199   n/a
        host    VP1P5                    1500   n/a
        host    VP1P8                    1800   n/a
        host    VP5P0                    4999   n/a
        host    VP7P0                    6999   n/a
        host    VP2P5_DB                 2500   n/a
        host    VP1P8_DB                 1800   n/a
        host    VP1P5_DB                 1501   n/a
        host    VP1P2_DB                 1200   n/a
        host    VP0P75_DB                 751   n/a
        host    VP1P05_DB                1049   n/a
        host    VP1P0_SAC0_VDDA           999   n/a
        host    VP1P0_SAC0_VDDD_VDDACM   1003   n/a
        host    VP1P2_SERDES_PLL_LGN     1200   n/a
        host    VP1P0_SAC1_VDDD_VDDACM   1003   n/a
        host    VP1P0_SAC1_VDDA          1000   n/a
        host    VP1P0_SAC1_VDD           1000   n/a
        host    VP1P0_SAC0_VDD           1000   n/a
        host    VP1P0_DAO                1000   n/a
        host    VP1P0_KAW_LDO            1000   n/a
        host    VP1P0_MGTVCC_DAO          999   n/a
        host    VP1P2_SERDES_PLL_DAO     1200   n/a
        host    VP1P0_SKT_IO             1000   n/a
        host    VP1P0_SKT_CORE            999   n/a
        host    VP1P9_LDO                1900   n/a
        host    VP1P8_10GPHY_LDO         1800   n/a
        host    VP1P2_10GPHY_01          1199   n/a
        host    VP0P75_TMX_VTT            746   n/a
        host    VP3P3_OCXO               3299   n/a
        host    VP1P8_OCXO               1799   n/a
        host    VP1P0_ARB                1000   n/a






0/FT0/*

0/FT1/*



LED Information
---------------------------------------------

R/S/I   Modules LED             Status
0/RSP0/*
        host    Critical-Alarm  Off
        host    Major-Alarm     Off
        host    Minor-Alarm     Off
        host    ACO             Off
        host    Fail            Off

Fan Information
---------------------------------------------

  Fan speed (rpm) and run time (in hours) :
        FAN0    FAN1    FAN2    FAN3    FAN4    FAN5    FAN6    FAN7    FAN8    FAN9    FAN10   FAN11

0/FT0/* (Speed) 
        3540    3570    3570    3570    3600    3600    3570    3540    3570    3570    3570    3600
0/FT0/* (Run Time) 
        N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A
0/FT1/* (Speed) 
        3570    3600    3570    3540    3540    3570    3570    3540    3600    3600    3570    3570
0/FT1/* (Run Time) 
        N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A     N/A
Power Supply Information
---------------------------------------------

R/S/I   Modules         Capacity        Status
                        (W)
0/PM0/*
        host    PM      3000            Ok

0/PM1/*
        host    PM      3000            Ok

0/PM2/*
        host    PM      3000            Ok

0/PM3/*
        host    PM      3000            Ok

0/PM4/*
        host    PM      3000            Ok

0/PM5/*
        host    PM      3000            Ok


R/S/I           Power Supply    Voltage         Current
                (W)             (V)             (A)
 0/PM0/*         154.8          55.3             2.8
 0/PM1/*         110.2          55.1             2.0
 0/PM2/*          82.2          54.8             1.5
 0/PM3/*         221.2          55.3             4.0
 0/PM4/*          82.8          55.2             1.5
 0/PM5/*         111.8          55.9             2.0
--------------
Total:  763.0


R/S/I           Power Draw      Voltage         Current
                (W)             (V)             (A)
 0/FT0/*         300 **
 0/FT1/*         300 **
--------------
Total:  600.0


R/S/I           Power Draw      Voltage         Current
                (W)             (V)             (A)
0/RSP0/*         190.7          54.5             3.5
--------------
Total:  190.7


R/S/I           Power Draw      Voltage         Current
                (W)             (V)             (A)
   0/1/*         277.9          54.5             5.1
--------------
Total:  277.9
** Indicates worst case power draw

Power Budget Summary for Rack 0
--------------------------------


Power Shelves Type: AC
Power Budget Strict Mode: Disabled 

Total Power Capacity:                           18000W
Usable Power Capacity:                          9000W
Supply Failure Protected Capacity:              9000W
Feed Failure Protected Capacity:                9000W
Worst Case Power Used:                          1700W

 Slot                                                      Max Watts
 ----                                                      ---------
 0/1/CPU0                                                        400
 0/RSP0/CPU0                                                     350
 0/RSP1/CPU0                                                     350  (default)
 0/FT0/SP                                                        300
 0/FT1/SP                                                        300

Worst Case Power Available:             7300W
Supply Protected Capacity Available:    7300W
Feed Protected Capacity Available:      7300W


Altitude Information
---------------------------------------------

Altitude: 
*0/**/*
 1800 meters above sea level
RP/0/RSP0/CPU0:ios(admin)#$

 

Labels:
0 Helpful
5 Replies 5

srekrish
Cisco Employee
Cisco Employee

‎03-26-2018 02:39 AM

Hi,

    What is the software version you are running in ASR9010 ?

 

Regards,

~Sreekesh~

0 Helpful

knowledgecom
Level 1
Level 1
In response to srekrish

‎03-26-2018 02:42 AM

Currently I'm running 4.3.4 which is active. 

I have 5.3.4 in disk0 as well. 

 

 

RP/0/RSP0/CPU0:ios(admin)#sh install active
Sat Mar 26 05:17:09.485 UTC
Secure Domain Router: Owner

  Node 0/RSP0/CPU0 [RP] [SDR: Owner]
    Boot Device: disk0:
    Boot Image: /disk0/asr9k-os-mbi-4.3.4/0x100305/mbiasr9k-rsp3.vm
    Active Packages: 
      disk0:asr9k-mini-px-4.3.4
      disk0:asr9k-fpd-px-4.3.4
      disk0:asr9k-mpls-px-4.3.4
      disk0:asr9k-optic-px-4.3.4

  Node 0/1/CPU0 [LC] [SDR: Owner]
    Boot Device: mem:
    Boot Image: /disk0/asr9k-os-mbi-4.3.4/lc/mbiasr9k-lc.vm
    Active Packages: 
      disk0:asr9k-mini-px-4.3.4
      disk0:asr9k-mpls-px-4.3.4
      disk0:asr9k-optic-px-4.3.4

RP/0/RSP0/CPU0:ios(admin)#



RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#show install inactive
Sat Mar 26 05:17:36.844 UTC
Secure Domain Router: Owner

  Node 0/RSP0/CPU0 [RP] [SDR: Owner]
    Boot Device: disk0:
    Inactive Packages: 
      disk0:asr9k-services-infra-5.3.4
      disk0:asr9k-bng-px-4.3.4
      disk0:asr9k-doc-px-4.3.4
      disk0:asr9k-mcast-px-4.3.4
      disk0:asr9k-mgbl-px-4.3.4
      disk0:asr9k-services-px-4.3.4
      disk0:asr9k-video-px-4.3.4
      disk0:asr9k-asr901-nV-px-5.3.4
      disk0:asr9k-9000v-nV-px-5.3.4
      disk0:asr9k-bng-px-5.3.4
      disk0:asr9k-doc-px-5.3.4
      disk0:asr9k-fpd-px-5.3.4
      disk0:asr9k-k9sec-px-5.3.4
      disk0:asr9k-li-px-5.3.4
      disk0:asr9k-mcast-px-5.3.4
      disk0:asr9k-mgbl-px-5.3.4
      disk0:asr9k-mini-px-5.3.4
      disk0:asr9k-mpls-px-5.3.4
      disk0:asr9k-optic-px-5.3.4
      disk0:asr9k-services-px-5.3.4
      disk0:asr9k-video-px-5.3.4

  Node 0/1/CPU0 [LC] [SDR: Owner]
    Boot Device: mem:
    Inactive Packages: 
      disk0:asr9k-services-infra-5.3.4
      disk0:asr9k-bng-px-4.3.4
      disk0:asr9k-mcast-px-4.3.4
      disk0:asr9k-services-px-4.3.4
      disk0:asr9k-video-px-4.3.4
      disk0:asr9k-bng-px-5.3.4
      disk0:asr9k-k9sec-px-5.3.4
      disk0:asr9k-li-px-5.3.4
      disk0:asr9k-mcast-px-5.3.4
      disk0:asr9k-mini-px-5.3.4
      disk0:asr9k-mpls-px-5.3.4
      disk0:asr9k-optic-px-5.3.4
      disk0:asr9k-services-px-5.3.4
      disk0:asr9k-video-px-5.3.4

RP/0/RSP0/CPU0:ios(admin)#
0 Helpful

smilstea
Cisco Employee
Cisco Employee

‎03-27-2018 10:33 AM

Does the MOD80 work in another slot?

Do you have a spare MOD80 you can try?

What is the serial number of the MOD80?

 

Most likely it will need to be RMAed so long as it is a genuine Cisco part.

 

Thanks,

Sam

0 Helpful

knowledgecom
Level 1
Level 1
In response to smilstea

‎03-29-2018 03:03 AM

upgraded to 6.2.3 still getting the error. 

 

 

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh platform
Thu Mar 29 04:07:35.899 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              MBI-RUNNING      PWR,NSHUT,MON
0/2/0           A9K-MPA-20X1GE            BOOTING          NPWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#sh platform
Thu Mar 29 04:08:08.503 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              ROMMON           PWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#sh platfor
Thu Mar 29 04:10:07.159 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              IOS XR PREP      PWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#LC/0/2/CPU0:Mar 29 04:10:48.879 : prm_server_ty[321]: %PLATFORM-NP-0-INIT_ERR : np_thread_channel_bringup  NP1 has failed to initialize.   
LC/0/2/CPU0:Mar 29 04:10:48.980 : pfm_node_lc[308]: %PLATFORM-NP-1-NP_INIT_FAIL_NO_RESET : Set|prm_server_ty[180307]|0x1008001|Persistent NP initialization failure, linecard reload not required. 
LC/0/2/CPU0:Mar 29 04:11:13.421 : lda_server[65]: %PLATFORM-UPGRADE_FPD-4-DOWN_REV : fpga3 instance 0 is down-rev (V0.08), upgrade to (V1.01). Use the "upgrade hw-module fpd" CLI in admin mode. 
LC/0/2/CPU0:Mar 29 04:11:32.133 : li_ea[269]: %PKT_INFRA-FEA_DLL-3-TCAM_ERR : TCAM create region error: 'prm_server' detected the 'warning' condition 'NP is down' 
RP/0/RSP0/CPU0:Mar 29 04:11:40.230 : licmgr[322]: %LICENSE-LICMGR-4-PACKAGE_LICENSE_INVALID : Package requesting A9K-LI-LIC license is activated on Rack0 and node node0_RSP0_CPU0 without a valid license/ valid configuration 
LC/0/2/CPU0:Mar 29 04:11:43.144 : lda_server[65]: %PLATFORM-SCC-2-BAD_ID_HW : Failed Identification Test in 0/130/0 [5/0] The module in 0/130/0 in this router may not be a genuineCisco product.  Cisco warranties and support programs onlyapply to genuine Cisco products.  If Cisco determines thatyour insertion of non-Cisco SPA cards or other modules into aCisco product is the cause of a support issue, Cisco maydeny support under your warranty or under a Cisco supportprogram such as SmartNet.   

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh platform
Thu Mar 29 04:12:10.307 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              IOS XR RUN       PWR,NSHUT,MON
0/2/0           A9K-MPA-20X1GE            OK               PWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#LC/0/2/CPU0:Mar 29 04:12:13.163 : lda_server[65]: %PLATFORM-LDA-4-MPA_OIR_QUICK_BACK_TO_BACK_ERROR : OIR operation was performed on MPA in bay:0 while the system is initializing. Recommend waiting for two minutes after EP initialized. 
LC/0/2/CPU0:Mar 29 04:12:13.259 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/19, changed state to Down 

RP/0/RSP0/CPU0:ios(admin)#LC/0/2/CPU0:Mar 29 04:12:13.259 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/18, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.259 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/17, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.260 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/16, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.260 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/15, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.260 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/14, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.260 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/13, changed state to Down 

RP/0/RSP0/CPU0:ios(admin)#LC/0/2/CPU0:Mar 29 04:12:13.260 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/12, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.260 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/11, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/10, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/9, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/8, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/7, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/6, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/5, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/4, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/3, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/2, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.261 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/1, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:13.262 : ifmgr[218]: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/2/0/0, changed state to Down 
LC/0/2/CPU0:Mar 29 04:12:14.196 : lda_server[65]: %PLATFORM-LDA-3-MPA_SW_ERROR : MPA failure in bay: 0, Module has been shutdown due to identify test failure (0x00000000 - No error)  : pkg/bin/lda_server : (PID=45089) :  -Traceback= 49a1f9a4 4a2cf618 4a2cc1d0 4941ae8c 49418f48 4a2cb2e0 4949b410

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh platform
Thu Mar 29 04:12:22.866 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              IOS XR RUN       PWR,NSHUT,MON
0/2/0           A9K-MPA-20X1GE            UNKNOWN          PWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#RP/0/RSP0/CPU0:Mar 29 04:14:30.917 : pfm_node_rp[374]: %PLATFORM-DIAGS-3-PUNT_FABRIC_DATA_PATH_FAILED : Set|online_diag_rsp[221310]|System Punt/Fabric/data Path Test(0x2000004)|failure threshold is 3, (slot, NP) failed: (0/2/CPU0, 1)  

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh platform
Thu Mar 29 04:14:38.417 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              IOS XR RUN       PWR,NSHUT,MON
0/2/0           A9K-MPA-20X1GE            UNKNOWN          PWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#show tech-support 
Thu Mar 29 04:15:02.114 UTC
++ Show tech start time: 2018-Mar-29.041502.UTC ++
Thu Mar 29 04:15:02 UTC 2018 Waiting for gathering to complete
..............................
Thu Mar 29 04:17:09 UTC 2018 Compressing show tech output
Show tech output available at 0/RSP0/CPU0 : /net/node0_RSP0_CPU0/harddisk:/showtech/showtech-generic-admin-2018-Mar-29.041502.UTC.tgz
++ Show tech end time: 2018-Mar-29.041709.UTC ++
RP/0/RSP0/CPU0:ios(admin)#sh platform
Thu Mar 29 04:20:18.755 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP440-SE(Active)     IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        ASR-9010-FAN              READY            
0/FT1/SP        ASR-9010-FAN              READY            
0/2/CPU0        A9K-MOD80-TR              IOS XR RUN       PWR,NSHUT,MON
0/2/0           A9K-MPA-20X1GE            UNKNOWN          PWR,NSHUT,MON
0/PS0/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS0/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M0/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M1/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
0/PS1/M2/SP     A9K-3KW-AC                READY            PWR,NSHUT,MON
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh hw-module fpd location all 
Thu Mar 29 04:22:46.456 UTC

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/RSP0/CPU0  A9K-RSP440-SE              1.0   lc   cbc     0      16.116    No 
                                              lc   fpga2   0       1.10     No 
                                              lc   fpga1   0       0.11     No 
                                              lc   fpga3   0       4.09     No 
                                              lc   rommon  0       0.76     No 
--------------------------------------------------------------------------------
0/FT0/SP     ASR-9010-FAN               1.0   ft   cbc     7       4.03     No 
--------------------------------------------------------------------------------
0/FT1/SP     ASR-9010-FAN               1.0   ft   cbc     8       4.03     No 
--------------------------------------------------------------------------------
0/2/CPU0     A9K-MOD80-TR               1.0   lc   cbc     0      20.118    No 
                                              lc   fpga2   0       1.04     No 
                                              lc   fpga4   0       1.05     No 
                                              lc   rommon  0       3.03     No 
--------------------------------------------------------------------------------
RP/0/RSP0/CPU0:ios(admin)#  
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh install active
Thu Mar 29 04:24:15.206 UTC
Secure Domain Router: Owner

  Node 0/RSP0/CPU0 [RP] [SDR: Owner]
    Boot Device: disk0:
    Boot Image: /disk0/asr9k-os-mbi-6.2.3/0x100305/mbiasr9k-rsp3.vm
    Active Packages: 
      disk0:asr9k-mini-px-6.2.3
      disk0:asr9k-services-infra-6.2.3
      disk0:asr9k-9000v-nV-px-6.2.3
      disk0:asr9k-bng-px-6.2.3
      disk0:asr9k-doc-px-6.2.3
      disk0:asr9k-fpd-px-6.2.3
      disk0:asr9k-k9sec-px-6.2.3
      disk0:asr9k-li-px-6.2.3
      disk0:asr9k-mcast-px-6.2.3
      disk0:asr9k-mgbl-px-6.2.3
      disk0:asr9k-mpls-px-6.2.3
      disk0:asr9k-optic-px-6.2.3
      disk0:asr9k-services-px-6.2.3
      disk0:asr9k-video-px-6.2.3

  Node 0/2/CPU0 [LC] [SDR: Owner]
    Boot Device: mem:
    Boot Image: /disk0/asr9k-os-mbi-6.2.3/lc/mbiasr9k-lc.vm
    Active Packages: 
      disk0:asr9k-mini-px-6.2.3
      disk0:asr9k-services-infra-6.2.3
      disk0:asr9k-bng-px-6.2.3
      disk0:asr9k-k9sec-px-6.2.3
      disk0:asr9k-li-px-6.2.3
      disk0:asr9k-mcast-px-6.2.3
      disk0:asr9k-mpls-px-6.2.3
      disk0:asr9k-optic-px-6.2.3
      disk0:asr9k-services-px-6.2.3
      disk0:asr9k-video-px-6.2.3

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#sh install inactive
Thu Mar 29 04:24:25.350 UTC
Secure Domain Router: Owner

There are no inactive packages on the SDR.

RP/0/RSP0/CPU0:ios(admin)#
RP/0/RSP0/CPU0:ios(admin)#
0 Helpful

smilstea
Cisco Employee
Cisco Employee
In response to knowledgecom

‎03-30-2018 08:12 AM

As I mentioned in my prior comment this card will most likely need to be RMAed. The very few times we have seen this its due to a hardware problem not a software problem.

 

Thanks,

Sam

0 Helpful
Customers Also Viewed These Support Documents