Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Hi !My host header class mapclass-map type http loadbalance match-all REDIRECT 2 match http header Host header-value "www.xxx.org"does not match even i find the host header www.xxx.org in http fox host header field ?Any suggestions ?kr
Hi everybodyI'm new with ACE4710 maybe someone can help me with it.I need create configuration where:if ACE's got packets from IP 10.10.10.10 on port 8888 (OUTSIDE int) it has to redirected to 11.11.11.11 port 8888 (INSIDE int)if ACE's got from any o...
Hi,We are using a CSS11503 to loadbalance SIP traffic. There are no SIP proxies involved and we only want to loadbalance the SIP invites. The CSS is connected in a one-armed set-up. We do not want to NAT the source address so we have no group configu...
hiI wanted to know something about the ace appliance, do I loose any features if I choose to use the ACE in bridge mode (like nat,tcp reuse , ssl authenticator and termination and such...) ?thanks
Hi ,Managed to set up the connection between the ACE and an SNMP monitoring system. Tested it and found that it was working fine for SNMP performance parameters and traps like linkup/linkdown.Problem now is that we would like to monitor the failover...
Hello team,I configured my WAAS devices to auth against the tacacs server but unfortunately it is not working. Here are the steps that I completed so far:- created new account at tacacs server- configured new user on CM (My WAN > Admin) and associate...
Hi everyone,i have a problem with active ftp (passive ftp works fine).here is my conf :access-list ANY line 8 extended permit icmp any any access-list ANY line 16 extended permit ip any anyrserver host ftp1 ip address 10.0.151.131 inservicerserver ...
Hi AllI am trying to design a network with already existing Cisco ACE modules in 6509 which needs to load balance between the severs which are behind the firewall. I just need to know how to design this scenario as I am new to design as I come from i...
Hi AllCan you please advise , if I can use Application Control Engine Service Module in 6500 Switch as a reverse proxy instead of Microsoft ISA Server.Regards
Hello everyone,I need to balance L3 (routing) traffic using a cisco ace 4710 appliance with a "A3(2.5)" system version.My rserver are some BlueCoat Proxy-SG in "proxy-transparent" mode.My question is: is cisco ACE able to balance basic L3 traffic?I ...
Hi all,Just a quick question :Is it possible to match a field of the client certificate to make a Load balacing decision ?so that if a client has a cert with a CN or C field with a specific value that is is redirected to a specific serverfarm.Thanks,...
Welcome to the Cisco Networking Professionals Ask the Expert conversation. This is an opportunity to learn how to troubleshoot and monitor Cisco Wide Area Application Services with Bhavin Yadav and Chip Schneider. Bhavin is a Technical Support En...
we made a recent upgrade from 4.1.3 to 4.2.3, and now we have many messages in all waes that the transport license has not been purchased, but we are using the entrerprise license. any clue?2010 Oct 7 17:15:03 NSTSWE0001 last message repeated 3 time...
The browser displays the image that i attached to the discussion. The admin guide says this : If this page does not open automatically or if you receive an error, verify that IIS permissions are set correctly. But we can't permit all the IIS service...
Hi all ,Is it possible to use UCS Blade Servers in ACE Load Balancing ?? Please note that UCS Blade Servers are not connected directly to 6500 Switch where ACE Module installed .i am expecting a good suggestion from whether ACE or Switching ExpertTha...
