Application Networking

Hi Friends,I am facing some issues with routing on Cisco CSS. My requirement is that i want to make internal subnets accessible from external network(firewall). Please have a look at the diagram, i want to reach 10.87.12.0/24 and 10.87.16.0/24 subnet...

We have rolled out 512 WAEs on the edges and a couple of the 7326 on the core. The average bandwidthbetween an edge and the core sites is about 2 MB..We're only doing the CIFS files for now and getting a pretty good performance on them (80-90% compre...

Hi All, I am using NM-WAE-502 in 2811 router. whenever I apply "ip wccp 61 redirect in" command on router internal interface, I lose internet connectivity. I just followed up every command and configuration steps based on documents. where should I lo...

Hi to all,I have two rservers (in this case they are firewalls) and they have to replicate active sessions to each other in case one of them is gone. But I am not able to configure both as a backup-rserver for each other. It says "Cannot assign backu...

Hi,I need some help regarding network design. We have 40 branches , each other connected by MPLS and also to the data centre. Now we want redundant link to connect other branches with the data centre. Each branches and data centre also having interne...

I had to take out the standby ACE from production today and want to insert it back now .. what is safe way to add it back ..It will be good if we can remove the peer address from the standby ACE and add it.. But for that i have to insert the ACE to t...

We have rolled out the 512 wae's to the edges and 7326 wae's to the core and having an issue with a cad/cam app as it's very slow...Does anybody have any experience with "taming" a cad/cam app in the wae's?thanks..

Hi, Does anyone know of any troubleshooting guide/materials available for Cisco ACE. I couldn't find any. Thanks.

Hi. I am configuring the ACE to loadbalance the TACACS+ traffic. I have:* An ACE module on a 6509* Cisco ACS running on Windows* Cisco WLC RADIUS Configuration works, but I am don't know how to configure TACACS+ or AAA Authentication / LBI found a co...

Hi All, Base on my understanding, we can run CM on 274 appliance with enterprise license. my question is: if company wants to save money and use 274 as AA, is it possible to implement waas 4.1 solution without even have CM? or CM is the mandatory pie...

ACE version Software loader: Version 0.95 system: Version A1(7b) [build 3.0(0)A1(7b) Cisco ACS version 4.0.1I am trying to authenticate admin users with AAA authentication for ACE management.This is what I've done:ACE-lab/Admin(config)# tacac...

How to put CNR application into Network Monitoring System? Because normally we probe using IP address to the Computer/box.The reason of probing for CNR only, we want to monitor whether CNR is reachable (still responding). We encountered last time onc...

I have an issue with access to a VIP on the CSS. The CSS is designed as a Dual Arm with two interface bridging a L2 L/B Vlan and a L2 Non L/B Vlan. The firewall in front of the CSS acts as a L3 gateway.Client > FW (L3 VLAN) > L2 Switch (L2) > CSS > ...

With the latest CSM 4.2(10) code I've noticed that after initiating a config sync from the active CSM it takes approximately 30 secs for the standby CSM to register the configuration download status as 'PENDING'. CSM code prior to 4.2(10) would regi...

There are two ssl modules running on the two individual cat6500 switches. Two weeks ago, we updated the image of ssl module as 3.1(4).From the release note, we know that because the SSLM receives time setting from the supervisor engine, Network Time ...