Hello Community, I am a newbie trying to get my hands on couple of Routers. I have been going through lot of docs and videos but kinda stuck with these 2 questions. 1. Is it possible to use 3 Ethernet ports of Cisco Router 4331? The requirement is to...
Forum Posts
hello , How i can enable port 8043 in Serveur cisco prime network 5.2 installer sur redhat linux !! which command enbale in Linux !! i wait a reply from expert cisco prime network and expert linux and help me . Best regards
Hi Community, I've recently installed fex N2K-C2348UPQ, but it didn't come UP. The uplink one the 5K switches stuck on "SDP timeout/SFP Mismatch". I've already upgraded the NX-OS to 7.2.1 and reload the fex several times but still the same issue. Bel...
Hi all,This is going to be a basic question, but I've come across a Cisco ACE that I've been asked to migrate the load balancing configuration off onto an alternative ADC.I have the configuration but it contains two entries for the same IP/Port infor...
Hallo; I'm using Python/Requests for api call to DNAC. The same problem described is also from DNAC itself (dna/platform/app/consumer-portal/developer-toolkit/apis).Edge device is discovered, added to site and provisioned and now ready to insert into...
Hello We're setting up an scenario with 2 Proxy using WCCP to distribute the load. The switches are catalyst 3750X so we're using redirect in. L2 redirection and mask to optimize forwarding of redirected packet.I would like to know can we use mask va...
I am trying to get PNP working via APIC-EM/Prime and I need to replace the local cert with one than has the FQDN as a SAN. I've tried to create the request on the APIC itself, but it tells me that the keyfile is the wrong format. I created and submit...
Resolved! Password Recovery for ACE service module
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the passwo...
while upgrading the Spine switch manually, it enters a boot loop and shows this error: ERROR ERROR SYSTEM IMAGE CORRUPIn /etc/rc6.d/S9[ 66.386004] reboot: Restarting system Do you have any idea, how to resolve this? Thnx
Hello All, Not sure if this has been answered or not before, but I have not found anything regarding this. 1-Box and 2-Box design for SD-A and SD-WAN integration CVD states the scaling is reduced for the DNAC substantially. But, it does not ide...
Resolved! update DNAC
System Update System 1.3.0.159Current version: 1.3.0.147System update failed during DOWNLOADED_MAIN_PACKAGE. ERROR: Downloading update package main-system-package:1.3.0.159 failed (Downloading systemUpdatePackage main-system-package:1.3.0.159 failed)...
Hi, please find the attached head snap let us know how I can configure this topology, currently, vPC is configured between firewall and nexus.
Hi I was wondering if anyone can help point me in the right direction: I am working on decommissioning a Cisco CSS 11501 and have a service called ssl-module which refers to a proxy list. The service has a number of local connections and I want to tr...
I have WASS now running between my 4431 on 16.6.X and 4351 with no issue.Another division of the company has a 4431 running 15.4(3)S6a, Is it possible to make a connection this 4431 running 15.4.x code? Upgrade of the 15.4 code to 16.6.x isn't an op...
Can't reregister a WAE back to the CM. I've deleted it from the CM and did a "deregister force" on it and still won't reregister. Any ideas? I've tried everything. I don't want to use the rescure disk at a remote site!version 4.4.1cms deregister forc...
