Application Networking

How do I remove a keepalive that does not exist but yet it does. I created a global keepalive. I went to add the keepalive to a service and it gave me an error that the maximum keepalives were exceed, which was not true. I went and activated the keep...

Hi Guys,I am currently trying to set-up GSLB between two CSS11501 running advanced feature set.One is to be housed in one geographical location the other in our DR site.I am wanting to use Roundrobin DNS to load balance between both sites and also ne...

HiI have a CSS 11050 with s/w ver 6.10 Build 304 (ap0610304).In conf t mode, it doesn't seem to have the prelogin-banner <filename> command.I've ftp'ed a prelogin message as an ascii file to the share directory but can't invoke it.Any ideas ?ThanksIa...

All,I have a css11501 and I have a situation where there are 2 servers in disparate datacenters, that I would like to balance requests to, based on URL requested - using http redirects.Clients come in and request http://X.X.X.X:4100/blah/whatever.asp...

I have recently implemented a CSS11506 transparent cache solution to a cache engine. All client port 80 traffic is redirected to the cache and everything works OK.On the cache engine I have the feature where by for certain sites I can choose not to c...

Hi,How can I reset the offline diagnostic monitor password??I have followed the online doc, however it simply keeps asking me for the username and password?Can anything be done from the boot prom to reset?Please help CheersScott

We have a content engine network module for a 2821 router located at a branch office that we'd like to use for clients to obtain locally cached file objects from a Windos server located at our headquarters or corporate office. I've been looking for s...

xxxxx.xxxxx.com ProxySG: 60003 WCCP has been initialized(0) NORMAL_EVENT ../cag_main.cpp 570I've been geeting this on our network alot but, we don't have WCCP enabled on any of the routers or switches. Just seems unusual that something is trying to i...

Hello,GSS sticky feature, does anybody use that with RR algrithm ?In the current environment I have issue when GSS's (we have 4)don't have time to agree on how to stick up with specific rule.One GSS sticks up withy one onswer, second with another.As ...

I am in the process of configuring a second CSS for failover. I want to have servers in two different locations that are attached to a layer 2 switch and then connect to the content switches. I also want all servers to continue working when one of th...

Hello,does anybody use keepalive to VIP and TAG from GSS to CSS ?We have SSL module on CSS as "front-end" service which is always alive (hopefully).To monitor "back-end" service with same IP we need to use this feature.There is a note on CCO, pretty ...

I had two networks 172.16.1.0 & 192.168.1.0 network we require load balance on both the network.I had extended the 172.16.1.0 network & created circuit on the content switch & same way for 192.168.1.0 network.Please find the below config.can any body...

1- haw i can load balance between 2 ACS using CSS , specialy what kind of keeplaive shal i use it to know if the server i mean ACs is up or not or the service is up or not 2- what is best Redundancy setup i ahve to implment it with the load balancing...

Is it possible to have the standby CSM configuration to be automatically synchrinized when a change occurs on the active CSM, or the only way to synchronize both config is to use the manual "hw-module csm x config-sync" command ?Thank youYves

Dear all,I have little question:What is the TCP timeout on CSM between for a request (ex a SYN) and a response (SYN/ACK)? Are the reverse-sticky with predictor leastconns or predictor hash only for FTP-like application? Why do you use reverse-sticky?...