Application Networking

In testing my backup configuration, I can take my primary real oos and my failover comes up just as it is intended to do. But, if I simulate a hardware failure on the primary, the failover doesn't come up.In searching through the forums, I've come a...

Can you explain what the following entries in my sys.log file mean? These 2 lines are repeated a few times in the log file. (WebNS version 07.30.0.05):OCT 25 09:23:53 1/1 118420 SYSSOFT-4: Communications-QUEUE FULL-Ipv4SlaveArpTx: Internal Messages D...

Hi,I want to configure firewall load balancing as follows. I have 3 firewalls, FW1, FW2, FW3. I want to create a serverfarm for each FW, i.e. FW1 in SF1, FW2 in SF2, and FW3 in SF3. Then, we'd like to create two Virtual server VS1 and VS2. Each Virtu...

Is there a way to change an owner name, short of creating a new one and re creating all the rules defined under the old name in the new one?

Hi all, Our customers have asked if it is possible with our current CSS, to let the CSS act as a SSL termination deviceSo that the webservers get less burden, just plain httpAs far as I understand it, you have to order a 11501 immediately with the SS...

I have a CSS11503 running s/w version 7.10 Build 504.The problem I am having is that wehn the CSS detects webservice has failed and marks it as down, The CSS does not recognise when the Web Service comes back online. We have to manually go intio the ...

Hi,I have the following situation :- CSS1 and CSS2 with VIP redundancy- CSS1 is the master, CSS2 is the backup for the VIP- Arrowpoint-cookie is used for stickyness- Six services defined in the configurationIn case of fail-over to CSS2, I would like ...

I have Cisco content engine 507 needs to be integrated with Trend Micro’s Inter-Scan Web Security Suite, What is the best way that would speed up the internet access,Configure the CE in Nontransparent mode where all web clients through IE point to CE...

Hi I wondered if anybody has deployed ACNS 5.2 in the wild so to speak yet? I'm planning on doing a major upgrade next month (bout 3 weeks time) and was all set to plan it when I recieved a note from ACNS Software team saying the version of code had ...

I upgraded a GSS 4480 (not 4490!) to version 1.1(1.1.0). It does seem to work properly, however, I get the following output from the status command:#gss status Cisco GSS - 1.1(1.1.0) - Sustaining Release GSSM - primary [Thu Oct 28 13:30:4...

I used "ntp server xxx.xxx.xxx.xxx (CDM IP)" on the CE config mode to have the CE time synced to the CDM, however the time on the two boxes are still different. How can i make the time sync work?ThanksGary

Can the same make decisions based on inso inside a cookie such as jsessionid in a weblogic cookie? Or does it make decisions based on only cookie name?I know F5 has a cookie persistence patent , does this mean Cisco CSM cannot perform cookie persisit...

Hello,Suppose I have a pair of PIX, a pair of CSS and a server farm. What should be the placement from the outside to inside? PIX-CSS-servers or CSS-PIX-servers? What are the considerations?Of course, by using a pair of PIX and a pair of CSS I wan...

Hello!I would like to send syslog messages via the Ethernet management port on the css. I set up a management route, and tried to set the logging host command, and I get the following:%% SYSLOGD cannot go to local I/F, VIP, or APPCould anyone help me...

Hi all, If a second SCM is installed in a CSS11506 Chassis, what is the amount of memory on board. I know the primary SCM has 288MB on Board. But some information say that only 144MB are on the redundant SCM Module. Help needed urgent. Regards Richar...