Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
OK here is the deal. I need to learn as much content networking as possible between now and the end of September. How did you everyone here learn? I need reference material. Any ideas or links welcome. Thanks in advance for the help.bc
We have CSS 11000 that provides load balancing between several servers with configured max-session .How to configure that sorry server sends different reply:1) if all servers are down, it has redirect to page "sorry, server is down"2) in case of over...
I just receive a brand new GSS-4480 Global Site Selector device.The box is not configured and runs GSS software Version 1.0(0.24.3).When connecting my PC for he first time on the console port, I receive a login prompt like this : localhost.localdomai...
Hello, I have a question, does anybody know if a Service Selection Gateway (Cisco 7401 Router) is capable of terminating a L2TP Tunnel initiated by a GGNS ? Thanks in advance Andreas
According to CCO as following text, the remaining 25 percent of bandwidth is used for overhead, including Layer 2 overhead, control traffic, and best-effort traffic. I want to know why cisco choose 25 percent. why not 30% or 20%?If I config the max-r...
I have a problem to configure one-armed transparent mode. I cannot access the server with "https://9.9.9.1" even "http://9.9.9.1:80" and "http://9.9.9.1:81" operational. looks CSS cannot communicate properly with SCA.I couldn't figure out from CCO sa...
I have WCCP redirecting traffic for ports 80 and 81 to a CE (ACNS 5). Does anyone know whether there any way to determine how may packets were redirected on each port number?
I´m found in web site Cisco this note."Before you synchronize the CSS with an SNTP server, make sure you configure the proper time zone for the CSS (for example, to EST). Also make sure the time difference between the CSS internal clock and the SNTP ...
Is there a way on the CSS 11000 series 11154 when a request for a url comes in default to port 80 to edit the http host header on the backend to change to a different port number then when returning to the client change it back to port 80.example def...
Hey guys!I have a big troble about my CDM 4650. When I rebuild a raid controller, the flash disk - which is called sandisk flash- is corrupted. So I can't any message on console display.Who do you know this problem.Please help me!Cheers!
Hi,I have configured "sntp server 10.1.1.1" on my CSS11000, but it does not work. Anybody who has suggestions what I have to do to get it functioning.I am using sw-version 5.00(45) and a ntp-server on linux which works for all ios-routers without any...
I am wanting to know if it is possible to use WCCP within my corporate network. I have some Bluecoat Port 80 devices on each site, and one in a DMZ. I also have a 6509s with MSFCs on each site. Would it be easier to use WCCP or just the advanced forw...
My application generates except normal flow, flow which CSS treats as DoS attack. Both flows have the same source. I am afraid that, CSS can block proper flow.So, I have question: how long CSS blocks flow, from source which detected as source DoS?Krz...
Does anyone know how to check the status of NTP on a CE (ACNS 5.x)?The show ntp status yields:ntp enabledserver list: 10.28.22.1which doesn't tell me if the clock is synchronized.
Mon Jun 30 11:07:48 UTC 2003 CE ivt7305CEServer warning Unexpected critical error on the node hdb1 I can't find any reference to HDB1 my guess is Hard Drive Bay 1 .. but that's just a guess. And if it IS hard drive, bay 1.. then what do I do to recti...
