Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 24, 2025 through Friday, March 7, 2025. Our colleagues Kalyan Raja and Janardhan, will be waiting to assist you and reso...
Hi All, I am configuring a brand new deployment of DNAC 2.1.2! Exciting times ahead. I'm looking for a little guidance on how to define the hierarchy of my network. Some notes:- We have multiple campuses, with multiple buildings at each- Remote campu...
Dear All,I will be so thankful if you guide me in this Licensing Issue.can we use the DNA advantage license on the vEdge cloud as vEdge on branches or not?Best Regards
If we have for example two fabric sites site1,site2 and there is wan between the fabric sites so we will use IP-Transit at each fabric site to make all fabric sites can communicate together so from the SGT side we will use SXP protocol to exchange SG...
Hi Cisco Community, I am new to all DNA stuffs. I've purchased a bunch of C9200L-E (with the mandatory DNA Licence of 3 years for each) to add to my current architecture composed mainly of 2960X. As these new switches integrate an existing architect...
Hey all,DNAC and ISE in my fabric domain was integrated very well. Last week I had known bug with update which caused my DNAC to stop working normally. TAC solved the bug but now, my DNAC and ISE is not integrated via pxGrid. I wanted to delete ISE i...
A lot of angst towards NBN in 2017.5GN in Melbourne enters 2018 offering 5G services to businesses in Australia, one of the only ones to do so.IPO at launch (Nov 2017) was at 25 cents a share and has already reached 40 cents at start of trading today...
I have imported our Sites and and WIFI Maps from Prime which appears to have worked to get the images and locations in to DNAC. However the Site data perfectly transferred the GPS data across but the map data appears to have had incorrect GPS co-ord...
Hi I've watched a Cisco video on installing DNAC and it shows enp10s0 being used as a cluster link but the presenter assigns 1.1.1.1/24 to the link with no gateway. In documentation it shows that for a single node the cluster link doesn't need to be...
We have enabled smart licensing with a 9200L without any issues we activated it and it draws a Network Advantage and a DNA Advantage license as expected. On the switch, we can see that both the Network and DNA licenses are registered: swINF02#show ...
Good afternoon all,I recently reached out to one of the guys on our server team to create a storage location that I can use to backup our DNAC to. He sent me the path and IP for the storage location however when I try to setup configure the backup I ...
Hi, I would like to use my organization's DNA Center as a datasource within Grafana so that I can pull data from DNA to make custom dashboards in Grafana. I have already setup a TIG stack, and I have followed the steps in this link: https://blogs.ci...
Hi All. I have created new fabric network with DNA-Center from zero after our company had office migration and now I need help with completing Wide Area Bonjour installation. I had fabric network and Wide Area Bonjour installed in previous network, b...
Hi EveryoneI'm using the maglev wizard i.e. "sudo maglev-config update" to perform the initial configuration of a new DNAC appliance but after providing various items of IP address information at the appropriate prompts, I get the following error mes...
Hello everyone.I'm new to the Cisco U community. I heard about Cisco U on the Cisco Meraki community.So I have a Meraki Mx84 and Mx64, I would like to integrate Cisco U as my DNS. how to do it?thank you for everythingCisco U and Meraki Mx
I am trying to set up our lab DNA appliance but I don't have 10Gbps options. I saw in a document that the Enterprise port can run at 1Gbps. How do I do that? I have tried using a GLC-T but I haven't had any luck yet.
