- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-17-2020 03:40 AM - edited 01-17-2020 03:42 AM
Hello
We are deploying DNA Wirelesss Assurance with 1800s sensors.
Sensors has been provisioned in DNA-C.
And simpe Test Suite has been scheduled.
But there is no results.
==========================================================
In sensor CLI:
AP70F3.5A7A.0198#show dot11 sensor stats ## Network Assurance Sensor Statistics ## WSA Status: Enabled NA Connectivity: Connected NA Connectivity I/F: Wired http NA Server URL: https://10.64.128.127 Auth Type: EAP HTTP Proxy IP: PROXY_IP Backhaul SSID: CiscoSensorProvisioning Id-token: Port: PORT Total Test Cases Run: 0 Successful Test Cases: 0 Failed Test Cases: 0 Network Assurance 5G Radio Statistics -------------------------- Host Rx K Bytes: 0 Host Tx K Bytes: 0 Unicasts Rx: 0 Unicasts Tx: 0 Broadcasts Rx: 0 Broadcasts Tx: 0 Beacons Rx: 0 Beacons Tx: 0 Multicasts Rx: 0 Multicasts Tx: 0 CRC errors: 0 Network Assurance 2G Radio Statistics -------------------------- Host Rx K Bytes: 0 Host Tx K Bytes: 0 Unicasts Rx: 0 Unicasts Tx: 0 Broadcasts Rx: 0 Broadcasts Tx: 0 Beacons Rx: 0 Beacons Tx: 0 Multicasts Rx: 0 Multicasts Tx: 0 CRC errors: 0 AP70F3.5A7A.0198# AP70F3.5A7A.0198#show dot11 sensor test config Test Config Received Time: 2020-01-17 10:47:30.604699 { advancedConfig: { rssiThreshold: -75 } testConfig: { targetAPs: testSuiteName: test-1 name: Onboarding bands: BOTH scheduleInDays: 0 connection: WIRELESS frequency: { value: 30 unit: MINUTES } ssids: { username: null validTo: 0 layer3webAuthsecurity: null numAps: 0 id: 0 authTypeRcvd: null authType: WPA2_PSK ssid: retail-service authProtocol: null eapMethod: null certxferprotocol: HTTP qosPolicy: null layer3webAuthpassword: **** psk: **** layer3webAuthuserName: null bands: BOTH layer3webAuthEmailAddress: null certfilename: null profileName: retail-service password: **** certstatus: ACTIVE wlc: 10.64.0.116 certpassphrase: null numSensors: 0 status: ENABLED certdownloadurl: null wlanId: 0 validFrom: 0 } startTime: 1579257944554 repeatCountOnFailure: 2 numberOfApsToTest: 3 wlans: retail-service testSuiteDetails: { BUILDING: Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266 AREAID: 32328f6c-3c7a-409a-8e74-6f6130743b8c TESTSUITENAME: test-1 FLOOR: Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266/1 AREA: Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439 FLOORID: ba56b83d-a535-4d33-bcc4-2cc45b04851f TESTSUITEID: 5e219058a61fa7002016a29f BUILDINGID: 307a9eff-c1c4-4074-b9bc-fc7db74c3ddf } config: {} type: DEDICATED testSuiteId: 5e219058a61fa7002016a29f:!_ba56b83d-a535-4d33-bcc4-2cc45b04851f:!_Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266/1:!_307a9eff-c1c4-4074-b9bc-fc7db74c3ddf:!_Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439/6266:!_32328f6c-3c7a-409a-8e74-6f6130743b8c:!_Global/\u041c\u043e\u0441\u043a\u043e\u0432\u0441\u043a\u0438\u0439:!_test-1 } wlans: { username: null validTo: 0 layer3webAuthsecurity: null numAps: 0 id: 0 authTypeRcvd: null authType: WPA2_PSK ssid: retail-service authProtocol: null eapMethod: null certxferprotocol: HTTP qosPolicy: null layer3webAuthpassword: **** psk: **** layer3webAuthuserName: null bands: BOTH layer3webAuthEmailAddress: null certfilename: null profileName: retail-service password: **** certstatus: ACTIVE wlc: 10.64.0.116 certpassphrase: null numSensors: 0 status: ENABLED certdownloadurl: null wlanId: 0 validFrom: 0 } } AP70F3.5A7A.0198#show dot11 sensor test results AP70F3.5A7A.0198#
NTP has been configured via CLI
AP70F3.5A7A.0198#show ntp NTP server Stratum Version Last Received Delay Offset Jitter time.moscow.spo 2 4 1827sec ago 0.000ms 0.000ms 0.000ms
As you see test suite is configured on sensor but there is no result
Please help to troubleshoot this issue?
Thanks.
Solved! Go to Solution.
- Labels:
-
Cisco DNA Assurance
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2020 06:45 AM
You are running old sensor code which isn't recommended since DNAC version 1.2.10. Please attempt to upgrade at least 8.8.263.0:
-- https://software.cisco.com/download/home/286318948/type/286288051/release/8.8.263.0
Since your 1800s sensor has already been claimed and in your DNA center inventory, you can use SWIM to upgrade the software on the sensor from the DNA center GUI.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-17-2020 07:34 AM
What DNAC version do you have deployed?
What version is the 1800s running?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-19-2020 08:54 PM
Hello
1800s Running Image : 8.8.259.0
DNAC maglev, version 1.3.0.3938
sensor-assurance Assurance - Sensor 1.4.0.484
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-19-2020 11:07 PM - edited 01-19-2020 11:13 PM
As i see test suits does not run on to the sensors
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2020 06:45 AM
You are running old sensor code which isn't recommended since DNAC version 1.2.10. Please attempt to upgrade at least 8.8.263.0:
-- https://software.cisco.com/download/home/286318948/type/286288051/release/8.8.263.0
Since your 1800s sensor has already been claimed and in your DNA center inventory, you can use SWIM to upgrade the software on the sensor from the DNA center GUI.
