I just bought the cml 2.6 and I am finding it difficult to set it up. After trying several times I finally got to the webUI to see that KVM/VMX and Images shows not ready. I need your help with this please. Thank you
Forum Posts
Three years ago I've built in EVE-NG a full Viptela SD-WAN lab, with vEdge, vBond, vSmart, and then even added cEdge (CSR1kvNG). Back then, there was no need to have any of these components call home to Cisco for whatever reason.Fast forward to today...
In ISE v3, in Identities and in Network Devcies, I want to re-size the column widths. For example, the IP/Mask column isn't wide enough to show the whole address. Making the column wider is easy enough to do but it doesn't persist. If I leave that se...
Hi everyone, I am an engineering student and currently, I am participating in the Cisco IoT Fundamental: IoT Security course. I am trying to set up the PL-App on the Raspberry Pi based on the Lab's instruction using the Cisco PL-App Launcher but I go...
Does anyone have any recommendations for a more cost effective Cisco Switch and Wireless Controler Management System than DNA/Catalyst Center? We currently are running prime infrastructure and it works well for our needs. However, since it is going...
I've been tasked with ensuring our network devices are using approved ciphers, KEXs and MACs on our network devices. How can I get a listing from Cisco Nexus 9K switches for each NXOS version? Also, what about Firepower/FTD/FMC? On a client, I can...
I am trying to change the LO1 ( RF1) input from default 5.15 to 10.75 (KU band).I have set all the tuning parameter correctly but I keep getting error when I click on apply Problem Saving updatesUnable to SET value 10.75 Fail I even tried to perform...
Hi, I have seen milestones for 16.9.x XE IOS at End-of-Sale and End-of-Life Announcement for the Cisco IOS XE 16.9.x - Cisco but I cannot understand why the 16.9.8 MD version was released in 2021 September the 1st if date of end of software support ...
Hello,We have a Cisco SDA fabric with 9300 edge switches and a single 9500 border node, with DNAC version 2.3.3.6-70045. The fabric in question contains a VN with native ASM multicast enabled in the overlay and an IP pool with Layer 2 flooding turned...
We have two port channel uplinks per FI. One goes to our ACI network and one goes to our Legacy network.Before ACI came along, we were just using VLANs (not VLAN groups) and no vlans were assigned to the port channel. Since we only up-linked to one n...
We aren't required to follow a certain direction, but I know 2 years ago NSA & NIST essentially said use 8 because 9 wasn't yet vetted. Cisco had or does recommend type 9. What did you go with?Finally upgrading from the ones you can just paste and se...
Estoy haciendo una actividad en la que se me pide lo siguiente:"Pruebe la conectividad al servidor Cisco.srv en la PC. Desde el símbolo del sistema, emita el comando ping cisco.srv Puede tardar unos minutos para el retorno del ping. Se deben recibir ...
Hello!I am writing here, as I have a Cisco UCS C220 M3 server, which has been out of support and after end of life for a couple of years already (https://www.cisco.com/c/en/us/obsolete/servers-unified-computing/cisco-ucs-c220-m3-rack-server.html).As ...
is cisco ucs central 2.0(1t) has End of support date?
I couldn't find the right driver on Cisco support pages.Which driver software should we use in Win10, for the Cisco USB console cable to connect to the 4G 829 router with a mini USB port?We installed "CP210x USB to UART Bridge Virtual COM Port" drive...
