on 03-23-2014 09:09 PM
When this script receive a call it play prompt to calling party. When finishing playing then script handoff the call with the destionation number to IOS. (IOS will do the call setup and Tcl IVR service will be ended)
Hi.Excelent job!. Would you like to share some aspects of the configuration or variables? Thank you. Best regards! Jesus.
conf t | |
app | |
service <name of sevvice> <url:play_message_2_calling_then_connect.tcl> | |
param prompt-1 <url:name of audio file> |
example:
service paly2connect tftp://tftp/play_message_2_calling_then_connect.tcl
param prompt-1 flash:en_welcome.au
Hi Team
I need smilar thing about same stituation.
We want to play announce before ringing the phone. Does someone provide me working tcl script and configuration.
Call Flow
ISP--> SIP-VG-[TCL scrip should play announce file stored on VG] -SIP- CUCM-- Directory Number.
On this time, Tcl scrip working for pots dial-peer for following scnerio.
PSTN/PRI- -VG- CUCM- DN
"flash0:c2951-universalk9-mz.SPA.152-4.M6a.bin"
This is a new deployment.
CUCM version:10.0.1.12900-2
We have two CUCM server (Pub /Sub)
Application config;
File name:kisa2.au
!
application
service seskayit app_fax_detect.2.1.2.2.tcl
param mode listen-first
param prompt flash:kisa2.au
!
If you are looking for specific Fax script you can download it from below link else you can use above script.
Thanks,
Raghavendra
Hi Radhavendra,
I want to play announce before ringing the phone, after announce complated. call should be connected the phone.
It should work with voip dial-peer recently I have working scenerio with pots dial-peer. but when I added services incomming dial-peer I'm getting busy tone.
dial-peer voice 989 voip
description test
services seskayit
session protocol sipv2
session target ipv4:10.1.1.120
voice-class codec 1
dtmf-relay rtp-nte
fax-relay ecm disable
no fax-relay sg3-to-g3
fax rate 9600
fax nsf 000000
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
voice-class codec 1
voice-class sip bind control source-interface GigabitEthernet0/0
voice-class sip bind media source-interface GigabitEthernet0/0
dtmf-relay rtp-nte
no vad
Thanks
You can use above play_message_2_calling_then_connect.tcl file with below config for your case, please try with this simple script instead of fax script.
service paly2connect flash:play_message_2_calling_then_connect.tcl
param prompt-1 flash:kisa2.au
Thanks,
Raghavendra
Here is my config:
When i apply service play2connect on dial-peer 74001 I'm getting busy tone after removing service play2connect command phone is ringing. What could be problem.
incoming dial-peer,
dial-peer voice 74001 voip
service play2connect
session protocol sipv2
incoming called-number 091246527400$
voice-class codec 1
voice-class sip bind media source-interface GigabitEthernet0/0
dtmf-relay rtp-nte
fax-relay ecm disable
fax-relay sg3-to-g3
fax nsf 000000
no vad
service play2connect flash:play_message_2_calling_then_connect.tcl
param mode listen-first
param prompt flash:kisa2.au
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: