08-04-2014 12:28 AM - edited 03-14-2019 01:42 PM
Our customer needs, the Personal callback should be dialed using agents' phones = DirectPreview dialing mode.
In customer's environment (UCCE v8.5), there is SCCP Dialer and for personal callback VIP30 lines are being used - Preview mode.
Q1: I think, It is needed to set OutboundControl for EnterpriseSkillGroup. Is it possible?
Q2: Is it possible to disable CPA (in registry: DisableIPCPA). To disable the CPA for PersonalCallback in registry DisableIPCPA should be set to "1"?
Solved! Go to Solution.
08-05-2014 06:43 AM
no in regular it won't be populated, only in Personal callbacks it will be populated.
Regular CallBack:
Message = NEW_TASK; Length = 43 bytes
DialogueID = (15) Hex 0000000f
SendSeqNo = (1) Hex 00000001
MRDomainID = (1) Hex 00000001
PreviousTask = -1:-1:-1
PreferredAgent = Undefined
Service = Undefined
CiscoReserved = (0) Hex 00000000
ScriptSelector: 23060
Personal CallBack:
Message = NEW_TASK; Length = 54 bytes
DialogueID = (13) Hex 0000000d
SendSeqNo = (1) Hex 00000001
MRDomainID = (1) Hex 00000001
PreviousTask = -1:-1:-1
PreferredAgent = (5054) Hex 000013be
Service = Undefined
CiscoReserved = (0) Hex 00000000
ScriptSelector: PersonalCallback
Regards
Chintan
~please rate all helpful posts and mark them correct
08-04-2014 02:01 AM
Q1: I think, It is needed to set Outbound Control for Enterprise Skill Group. Is it possible?
yes you need to use preferred agent routing here, which can be accomplished with Enterprise skill group. and you don't need to set any Outbound Control here.
Q2: Is it possible to disable CPA (in registry: DisableIPCPA). To disable the CPA for PersonalCallback in registry DisableIPCPA should be set to "1"?
if you are using Direct Preview then the your agent has to deal with CPA, and they have to mark call on their desktop as call will be directly dialed from agents phone, so ideally dialer doesn't do any CPA here.
regards
Chintan
08-04-2014 02:15 AM
Hi Chintan,
thanks for your reply.
I've configured PersonalCallback like written in UCCE Outbound Option configuration documentation. It works pefectly, and sure, I'm using PrefferedAgentID value in object QueueToAgent.
Agent is in skillgroup and this skillgroup is in EnterpriseSkillgroup, which is used in ICM script in object QueueToAgent.
Usually, when administration script is configured for outbound, the outbound control is set as needed the campaign type (PREVIEW, DIRECT_PREVIEW, PROGRESSIVE...).
I need to set the EnterpriseSkillGroup to be DIRECT_PREVIEW_BLEND, because I need the contact from PersonalCallbakList should be dialed from agent's phone not form VIP30phones (curreently PREVIEW mode is used), but ...
It is not possible to set OutBoundControl in administration ICM script for Enterprise SKG.
There is no problem with routing the call to agent, but the PersonalCallback is dialed using Preview mode (not the DirectPreview as requested). Our customer needs, the call is dialed using agent's phone, so agent can hear signalisation (ringing, answer machine) and customer does not want to use CPA at all for PersonalCallback.
08-04-2014 04:38 AM
oh yes, i realized that the all type of personal call back will occur in PREVIEW MODE, and you can not set them.
see below note:
what if you disable CPA at campaign? have you tried that?
regards
Chintan
08-04-2014 11:16 PM
Yeah, you are right. I tried to disable CPA, but campaign setting of CPA does not configure CPA for PersonalCallback.
I have an idea, I'll use regular callback (this is in the same mode as Campaign mode = DirectPreview), but I'm not sure the value in variable PrefferedAgentID would be populated at the time agent sets the callback in CAD, when using Regular Callback
08-05-2014 06:43 AM
no in regular it won't be populated, only in Personal callbacks it will be populated.
Regular CallBack:
Message = NEW_TASK; Length = 43 bytes
DialogueID = (15) Hex 0000000f
SendSeqNo = (1) Hex 00000001
MRDomainID = (1) Hex 00000001
PreviousTask = -1:-1:-1
PreferredAgent = Undefined
Service = Undefined
CiscoReserved = (0) Hex 00000000
ScriptSelector: 23060
Personal CallBack:
Message = NEW_TASK; Length = 54 bytes
DialogueID = (13) Hex 0000000d
SendSeqNo = (1) Hex 00000001
MRDomainID = (1) Hex 00000001
PreviousTask = -1:-1:-1
PreferredAgent = (5054) Hex 000013be
Service = Undefined
CiscoReserved = (0) Hex 00000000
ScriptSelector: PersonalCallback
Regards
Chintan
~please rate all helpful posts and mark them correct
08-07-2014 12:18 AM
I've just figured it out too, :-(
Thank you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide