Buy or Renew
Buy or Renew

Controllers

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Learning Labs
Get hands-on with guided tutorials​
Sample Code
Find ready-to-use code samples​
YouTube
Watch tutorials and demos​

Forum Posts

Start a conversation

Issue With Adding SNMP RO String

I'm trying to add a RO community string for discovery in the APIC-EM controller and get the following error:Unable to add Read Community; 400:undefindedMy community string has a @ < > and ! character in it.  I'm assuming this is causing the issue as ...

Perfmon is not working

Perfmon is not working on the following devices4507 - Version 03.04.05.SG4500x - Version 03.04.05.SG3850 -  Version 03.03.01SE6509 - Version 15.1(2)SY4aI checked the list of supported device and found that it should work on 6509 as per below link:Cis...

raziahme by • Community Member
  • 801 Views
  • 0 replies
  • 1 Helpful votes

EPG and VLAN Creation

Hello,In my configuration I have three EPGs - EPG-1, EPG-2 and EPG-3.  Two static paths are created in EPG-2 and a static path is created in EPG-3.  All these three interfaces are on a common VLAN and contract established between these EPGs.  This is...

Resolved! Problem with discovery

HelloI'm facing problem with device discovery. I have 2 sites that has been discovered withou any issues. But when I tried to add another one today, I got "cli validation failure". There is no problem with routing nor ACL - snmp part works fine. I ch...

lukaszdewera by • Frequent Visitor
  • 5215 Views
  • 5 replies
  • 5 Helpful votes

Resolved! Questions about PnP

HiWe are running APIC-EM in our LAB environment and I have a few pending issues/questions before going into production.1. Is there a way to get the entire device configuration using the api? including passwords and snmp information etc.GET /network-d...

sw1ft-code by • Frequent Visitor
  • 2582 Views
  • 3 replies
  • 6 Helpful votes

Resolved! PNP DHCP option 43

Hi,I would like to use the G0 mgmt interface of a ISR4000 series router to do PNP. Is there a way to define the vrf that pnp should use via option 43? I can set the vrf for PNP http server to Mgmt-intf on the cli. It would be great if this could be d...

AB24 by • Frequent Visitor
  • 15594 Views
  • 15 replies
  • 7 Helpful votes

Resolved! {PNP}Streamlining Zero-Touch

Currently, we are using the dhcp method for pnp discovery. This has been working well, however, our current deployments depend on having 2 uplinks to our upstream switch. On the uplink switch, we use the first link as a trunk and pass specific vlans ...

zlantz by • Level 3
  • 13465 Views
  • 36 replies
  • 5 Helpful votes

Unable to access console APIC-EM 1.3.2.37

Hi All,First information.I need to restore Apic-em to default clean everything  ,then i've restoring the APIC-EM to the factory default by troubleshoot doc (from command  reset_grapevine factory).After process restoring  APIC-EM nothing changes.  Now...

kwanchai.szd by • Frequent Visitor
  • 1743 Views
  • 2 replies
  • 5 Helpful votes

Resolved! Resync function

Hi,I have found that there is a resync button in Device inventory. As I understand this function send signal to switch to get config file from PnP. I was triying to change config that is currently connected to switch in PnP and pushed Resync button I...

JPvisltgb by • Level 3
  • 2510 Views
  • 4 replies
  • 1 Helpful votes

a few more blogs - PnPTools and CommandRunner

Hi,for those that are interested, I have posted a few more blog rescently.One has some PnPtools in it.  including something to watch the deployment status.Network Automation with Plug and Play (PnP) – Part 8$ ./src/watch_provision.py FDO1732Q00BWatch...

aradford by • Cisco Employee
  • 1257 Views
  • 0 replies
  • 21 Helpful votes

List VRF names on each managed device?

Hi,api/v1/topology/vrf/vrf-name API call gives you a list of all VRFs discovered by the controller but it doesn't seem to identify on which devices these VRFs are. Has any body found an approach to actually list VRFs on each managed device?Thanks

Load more