Hi everyone! In an installation containing dozens of IR1101 spread over an extensive geographic area, what is the best option for remote update of the hosted application? IR1101 Software Configuration Guide mentions that application can be deployed u...
Forum Posts
Hello, My router is managed in IOT Operation Center.I have uploaded EI-Agent (Edge Intelligence) application.The application is running, but the agent is not registering in EI-Cloud.The application in IOX Local Device Manager is showing : app : unhea...
Resolved! LoRaWAN interface on Cisco 809 router
Hello guys,I have the following:Cisco 809 router (IR809G-LTE-GA-K9), with IP Base, Data and Security licenses (permanent)GPS antenna for the Cisco 809 (GPS-ACT-ANTM-SMA)LoRaWAN interface module and its software (IXM-LPWA-800-16-K9 & SW-IXM-LPWA-K9)GP...
Hi everyone! Regarding IR1101 application hosting: are the cellular interfaces mapped to the container that runs the application (via VirtualPortGroup)? Is it possible for a Docker type C based application to send/receive (via sockets) TCP frames to/...
C9500 does not have the AppGigabitEthernet interface for IOx apps, so it is slightly different from C9300. All the examples I have found on Cisco documents/blogs relating to IOx containers on C9500 only point to using management network for connectiv...
DEAR ALL IS THERE AN IOX APP FOR HOSTING A WEBSITE ON THE ISR 4331 ROUTER ?IF NOT CAN IT BE MADE ?
Question regarding C9000 application hosting: is Catalyst 9000 capable of running other applications besides Docker? Trying to find a better platform for developing IR800 series IOX applications. IR800 series is very limited. Can I use the C9000 for...
The Kinetic GMM APIs /v2/fog_installations/{id} allows to change specific application parameters before starting an IOx app. What development needs to be done to read these parameters in an IOx python applications built with docker?I already followed...
When building an IOx app using Docker and ioxclient, the app gets an internal IP address automatically 172.17.0.X. I need to make a connection to an IP address 192.168.0.xxx on port 502 using the Ethernet port GE1 of an IR809. in my configuration I d...
Hello everybody,today I installed the newest IOS for the IR1101 and the remote Docker support is finally here.I managed to get it working just by following the instructions on the iOX local manager and it is AWESOME.It is so much easier to deploy, te...
I'm trying to use the base image found at: iox-docker/ir800/base-rootfs/yocto-2.1.1/ , since it includes python3 support. Python2 is not an option; I need to use python requests module. The python2 compiled in the yocto1.7 image does not include co...
While attempting to perform a bundle install upgrade from ir800-universalk9-bundle.SPA.159-3.M1.bin to ir800-universalk9-bundle.SPA.159-3.M2.bin, one of my modems failed and is now in ROMMON-1. I have tried the rommon recovery procedure as described...
is there a way to tell a docker container to use a serial device in the IR829?I know that a typical Docker container can be granted serial device access with "docker run --device=/dev/ttyS3 ..."But how do I tell to the ioxclient/local manager to gran...
I have developed a IOX docker application and tried uploading in Sandbox, which is uploaded and running successfully,But when i try the same application uploading in the Hardware IR829, i am getting No space error,When i checked in sandbox after uplo...
Hi, I have a Cisco IR1101 and Cisco IR829WG. In both cases, I want to deploy containers with my application. For the IR1101, I used the instructions:https://www.cisco.com/c/en/us/support/docs/routers/1101-industrial-integrated-services-router/21438...
