cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1086
Views
5
Helpful
4
Replies

ATA 187 on gateway 2911 for SIP

Hi All

   I need your help in setting up configuring the ATA 187 on gateway 2911 router  for fax services.

configure the router SIP

Customer IP address= 172.22.21.2570/30

STC IP Address =            172.22.21.232/30

Protocol= SIP

SIP Port = 5060

Transport Protocol=UDP

Voice Codec= G711 A-Law

DTMF = IN-Band DTMF with RFC2833

SIP Server IP address = 10.201.7.151

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.3(1)T, RELEASE SOFTWARE (fc1)

CME version

CONFIG (Version=9.1)

=====================

Version 9.1

Max phoneload sccp version 17

Max dspfarm sccp version 18

Cisco Unified Communications Manager Express

Thanks,

1 Accepted Solution

Accepted Solutions

kaja_2kj3
Beginner
Beginner

Hi

    From my understanding,

Unlike the ATA 186/188, the 187 can only be configured via CUCM(Cisco Callmanager 7.1(5) and above only).

Under, Cisco ATA SIP services

• Cisco ATA configuration through Cisco UCM configuration interface

The ATA configuration has been simplified and streamlined to mimick that of an IP phone. All available options are now on the CUCM page for the ATA.

For more information, please see the following links

http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps514/ps11026/data_sheet_c78-608596.html

http://www.cisco.com/en/US/docs/voice_ip_comm/cata/187/1_0/english/administration/guide/sip/a187_ag2str.html#wp1102295

You just need a dial-peer at the gw as below,


! Fax configuration for Inbound / Outbound VoIP dial-peer


dial-peer voice voip

  fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through

  fax-relay ecm disable

  fax nsf 000000

  fax-relay sg3-to-g3

Please rate if this helps. by clicking the stars below.

Thanks

View solution in original post

4 Replies 4

kaja_2kj3
Beginner
Beginner

Hi

    From my understanding,

Unlike the ATA 186/188, the 187 can only be configured via CUCM(Cisco Callmanager 7.1(5) and above only).

Under, Cisco ATA SIP services

• Cisco ATA configuration through Cisco UCM configuration interface

The ATA configuration has been simplified and streamlined to mimick that of an IP phone. All available options are now on the CUCM page for the ATA.

For more information, please see the following links

http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps514/ps11026/data_sheet_c78-608596.html

http://www.cisco.com/en/US/docs/voice_ip_comm/cata/187/1_0/english/administration/guide/sip/a187_ag2str.html#wp1102295

You just need a dial-peer at the gw as below,


! Fax configuration for Inbound / Outbound VoIP dial-peer


dial-peer voice voip

  fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through

  fax-relay ecm disable

  fax nsf 000000

  fax-relay sg3-to-g3

Please rate if this helps. by clicking the stars below.

Thanks

thank you

how can  configure fax for cme ?

please send me the one solution.......

ATA 187 only supports SIP so you will need to add this as a SIP phone to CME. Once registered you can configure the appropriate dial-peers.

Off the top of head - you will need at the minimum below config to register your ATA to CME:

voice register global

mode cme

source-address

max-dn X

max-pool Y

voice register pool 1

id mac XX:XX:XX:XX

type ATA-187

number 1 dn 1

dtmf-relay sip-notify

codec g711ulaw

!

voice register dn 1

number XX

name Fax

label Fax

!

See below link for detailed configuration to register a SIP device - Its for 9971 but ATA setup will be quite similar:

http://www.cisco.com/en/US/partner/products/sw/voicesw/ps2156/products_configuration_example09186a0080b82d00.shtml

Terry

Thanks Terry

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers