Call into an MGCP controlled FXO port not connecting

[shabbarbabrawala]

my setup is

PSTN --- GW --- CUCM --- 6921 phone

when we call from the PSTN then call rings and shows connected on the PSTN phone after about 10 sec the call disconnects with fast busy but the 4 digit plar does not ring at all, outgoing calls are working fine. Need help in resolving this issue

Shabbar

[yahsiel2004]

Please post your GW configuration and describe your CUCM setup.

HTH

Regards,

Yosh

[shabbarbabrawala]

Attached the gw config what do you mean by cucm setup

[yahsiel2004]

How you have your FXO configured in CUCM. Can you post a "debug isdn q931"?

HTH

Regards,

Yosh

[shabbarbabrawala]

FXO is configured as loop start as below, cannot run the debug isdn

R_SCI_KQ#debug isdn q931

                 ^

% Invalid input detected at '^' marker.

Registration	Registered with Cisco Unified Communications Manager 192.168.0.26
IP Address	192.168.100.6
End-Point Name	AALN/S0/SU0/0@R_SCI_KQ.sciafrica.net
Description
Device Pool	DP_KQ -- Not Selected -- Cisco Unity voice Mail Ports DP_DAR DP_DRC DP_MOZ DP_ZAM UCCX
Common Device Configuration	< None >
Media Resource Group List	MRGL < None >
Packet Capture Mode	None Batch Processing Mode
Packet Capture Duration
Calling Search Space	< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
AAR Calling Search Space	< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
Location	Hub_None Kenya Mozambique Phantom Shadow Zambia
AAR Group	< None > AAR_GRoup
Network Locale	< None > Argentina Australia Austria Belgium Brazil Canada China Colombia Cyprus Czech Republic Denmark Egypt Finland France Germany Ghana Greece Hong Kong Hungary Iceland India Indonesia Ireland Israel Italy Japan Jordan Kenya Korea Republic Lebanon Luxembourg Malaysia Mexico Nepal Netherlands New Zealand Nigeria Norway Pakistan Panama Peru Philippines Poland Portugal Russian Federation Saudi Arabia Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey United Kingdom United States Venezuela Zimbabwe Itu Chile Bulgaria Croatia Romania Serbia and Montenegro United Arab Emirates Oman Kuwait Algeria Bahrain Iraq Mauritania Republic of Montenegro Morocco Qatar Republic of Serbia Sudan Tunisia Vietnam Yemen Lithuania Latvia Estonia
Use Trusted Relay Point	Off On Default
Transmit UTF-8 for Calling Party Name
Called Party Transformation CSS	< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
Use Device Pool Called Party Transformation CSS
Enable Caller ID

[yahsiel2004]

I'm sorry I was thinking about something else when I asked for the "debug isdn q931" you don't have any PRIs.

Regards,

Yosh

[Carlo Poggiarelli]

Hi.
Being an FXO it supposed to be connected to an analogue line not ISDN :)
a debug vpm all would be useful.

Please activate it , make an inbound call an please post the result

Thanks

Regards

Carlo

Sent from Cisco Technical Support iPhone App

[shabbarbabrawala]

Output of debug vpm all attached

[shabbarbabrawala]

Think the file did not copy completely

[Carlo Poggiarelli]

Hi Shabbar.
On the vg remove plar config and fill the attendant dn field on port configuration on CUCM with desired destination.

HTH

Regards

Carlo

Sent from Cisco Technical Support iPhone App

[shabbarbabrawala]

Hi

Removed the plar but still the same behaviour

[Carlo Poggiarelli]

Hi.

Did you configured the attendant DN on port configuration page on CUCM?

If yes, can you check the incoming CSS on the same configuration page?

Let me know

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"