Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About yahsiel2004
10-09-2017
Stats
Member since
03-17-2008
945
Posts
407
Helpful
82
Solutions
08-06-2015
05:44 AM
You can increase the interdigit timeout value, so that the user has more time before they have to dial a digit. telephony-service timeouts interdigit "1 - 120 seconds" HTH Yosh
... View more
Created by
yahsiel2004
in IP Telephony and Phones
in IP Telephony and Phones
08-05-2015
06:13 AM
08-05-2015
06:13 AM
Can you post your full config? Regards, Yosh
... View more
08-04-2015
08:46 AM
Mehmet, You can create an EEM script and put the commands needed to reset your PRI interfaces. Below is a link on how to setup an EEM script. http://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-embedded-event-manager-eem/116176-technote-eemscripts-00.html HTH Yosh
... View more
07-30-2015
06:10 AM
I understand if you are certain that the password is the same as the "OS Administrator" but unfortunately the issue you're facing is due to an incorrect password. You will need to reset the "Security Password" via the CLI. This issue occurs due to the mismatch of the administrator passwords or security passwords between the publisher and subscriber. The security password on all nodes in a cluster must match with that of the publisher. Maintain the same security password on all machines, or the cluster nodes are not able to communicate. http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-version-60/109486-cm-configuration-validation-error-00.html P.S. I know the document provided is an older version but the issue is still the same. HTH Yosh
... View more
07-29-2015
06:13 AM
Can you enable "voice iec syslog" and turn on terminal monitor and then make a call. The system will produce a reason code for the failed call.
... View more
07-29-2015
06:12 AM
Michael, What I meant is can you call the external number (outbound PSTN) normally? Just want to make sure the number is reachable externally. Your config looks fine. Are you using any "Application Dial Rule"? Regards, Yosh
... View more
Created by
yahsiel2004
in IP Telephony and Phones
in IP Telephony and Phones
07-29-2015
05:24 AM
07-29-2015
05:24 AM
Nash, You have to turn off "no ip address trusted authenticate" or add the trusted IP addresses to the "ip address trusted list". Also verify that your monitor logging is set to "debugging". HTH Yosh
... View more
07-29-2015
05:18 AM
You need provide more information then this... Can you call that end users external number normally? What are your SNR settings for that users (e.g. answer timers, delay timer, etc). Regards, Yosh
... View more
Created by
yahsiel2004
in IP Telephony and Phones
in IP Telephony and Phones
07-28-2015
04:59 AM
07-28-2015
04:59 AM
Is there internal users using "ephone-dn" or "voice register dn"? Regards, Yosh
... View more
07-23-2015
12:47 PM
Webber, The parameter you should be changing is the "Stop Routing on Unallocated Number Flag" to false.This option is what allows the call to keep routing to other RGs within a RL. Also you can configure the "voice class sip options-keepalive" on the dial-peer to monitor the status of Winstream. HTH Yosh
... View more
Created by
yahsiel2004
in IP Telephony and Phones
in IP Telephony and Phones
07-21-2015
12:30 PM
07-21-2015
12:30 PM
Which version did you upgrade from? You may need to check your "Enterprise Service Parameter" and very the non-secure URLs (e.g. http://X.X.X.X:8080/ccmcip/xmldirectory.jsp) HTH Yosh
... View more
07-21-2015
12:07 PM
Can you access your ESXi server via your vShpere client? If yes, did you assign a VLAN to the management vMKernel port? If yes, you will need to assign the same VLAN tag to the "Port Group" that is assigned to your VM.
... View more
07-21-2015
08:13 AM
Ajith, Just FYI. You can't upgrade the Subscribers unless the Publisher is running on the new version. Regards, Yosh
... View more
08-06-2015
You can increase the interdigit timeout value, so that the user has more
time before they have to di...
08-04-2015
Mehmet,You can create an EEM script and put the commands needed to reset
your PRI interfaces. Below ...
07-30-2015
I understand if you are certain that the password is the same as the "OS
Administrator" but unfortun...
07-29-2015
Can you enable "voice iec syslog" and turn on terminal monitor and then
make a call. The system will...
07-29-2015
Michael,What I meant is can you call the external number (outbound PSTN)
normally? Just want to make...
07-29-2015
Nash,You have to turn off "no ip address trusted authenticate" or add
the trusted IP addresses to th...
07-29-2015
You need provide more information then this...Can you call that end
users external number normally? ...
07-23-2015
Webber,The parameter you should be changing is the "Stop Routing on
Unallocated Number Flag" to fals...
07-21-2015
Which version did you upgrade from? You may need to check your
"Enterprise Service Parameter" and ve...
07-21-2015
Can you access your ESXi server via your vShpere client? If yes, did you
assign a VLAN to the manage...
Public Statistics
| Date Registered | 03-17-2008 07:10 AM |
| Date Last Visited | 10-09-2017 01:26 PM |
| Total Messages Posted | 945 |
| Total Helpful Votes Received | 407 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 50 | |
| 83 | |
| 105 |
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Cisco Employee"){kind=icon}
Helpful Votes From
| User | Helpful Count |
|---|---|
| 10 | |
| 65 | |
| 5 | |
| 4 | |
| 5 |
Awards
Community Spotlight Award
Mobile App Contributor January 2013
