12-08-2009 07:56 PM - edited 03-15-2019 08:43 PM
We've got CallManager lab set up with a SCCP phone registered to a "internal" CM7.1 publisher. The "internal" CM and a 2821 is setup to do MGCP BRI backhauling of one of the VIC2-2BRI-NT-TE interfaces(0/0/0). The 2821 has a BRI cross connect wire between interfaces 0/0/0 and 0/0/1. The 2821 is also configured for H323 and has dial peers associated with BRI interface 0/0/1. Another "pstn" CM7.1 publisher registers with the 2821 via H323. We also have xlite registered as a SIP client to the "pstn" CM.
Whenever the SIP client dials the number of the SCCP phone, the SCCP phone does a short ring and then stops. Can't seem to establish a call at all but some type of alerting is getting to it.. Any ideas?
Solved! Go to Solution.
12-08-2009 08:51 PM
Use g711 "u" instead of "a" on the Dial Peers. Also configure "Incoming called-number" with a pattern that covers all the sip phones in the VoIP Dial Peers.
MK
12-09-2009 11:52 AM
you can try:
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g729br8
dial-peer voice 2 voip
voice-class codec 1
destination-pattern 5041231234
session target ipv4:1.1.1.6
dtmf-relay h245-alphanumeric
12-09-2009 07:58 PM
hey Bill, glad it worked.
You can issue "show voice call status" which will give you codec being used.
As far as debugging informacion, the following will show codec negotiation:
debug h245 asn1
debug voice ccapi inout
Thanks!
Efrain
12-08-2009 08:51 PM
Use g711 "u" instead of "a" on the Dial Peers. Also configure "Incoming called-number" with a pattern that covers all the sip phones in the VoIP Dial Peers.
MK
12-09-2009 08:14 AM
I'm not sure what you mean My dial-peers are currently defined as follows:
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
port 0/0/1
!
dial-peer voice 2 voip
destination-pattern 5041231234
session target ipv4:1.1.1.6
dtmf-relay h245-alphanumeric
!
dial-peer voice 3 pots
destination-pattern .T
port 0/0/1
forward-digits all
!
12-09-2009 11:52 AM
you can try:
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g729br8
dial-peer voice 2 voip
voice-class codec 1
destination-pattern 5041231234
session target ipv4:1.1.1.6
dtmf-relay h245-alphanumeric
12-09-2009 05:50 PM
Adding the codec preference list to the dial peer got it working. Is there any debug commands I could have run to determine which codec the call was trying to use at the time?
12-09-2009 07:58 PM
hey Bill, glad it worked.
You can issue "show voice call status" which will give you codec being used.
As far as debugging informacion, the following will show codec negotiation:
debug h245 asn1
debug voice ccapi inout
Thanks!
Efrain
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide