Re: CCME Call establishment problem

antonio.dinapoli · ‎06-25-2007

Hi,

I have a 2821 router with CCME 4.0.2 that is connected to PSTN network via VIC2-4FXO.

I have a problem with call establishment because:

- when there is a call from PSTN network to IPphone, the associated FXO port rings but IP phones with the same phone number doesn't ring

- when there is a call from IP phone to PSTN network, the FXO port is correctly selected but the calls are not established

I have issued the command debug vpm all and then I tried a simulated call with the command "csim start <dialstring>" that failed.

These are the logs, anyone can help me?

Jun 23 09:54:14: htsp_timer_stop3 htsp_setup_req

Jun 23 09:54:14: htsp_process_event: [0/3/2, FXOGS_ONHOOK, E_HTSP_SETUP_REQ]fxog

s_onhook_setup

Jun 23 09:54:14: [0/3/2] set signal state = 0x0 timestamp = 0

Jun 23 09:54:14: dsp_set_sig_state: [0/3/2] packet_len=12 channel_id=130 packet_

id=39 state=0x0 timestamp=0x0

Jun 23 09:54:14: TGRM: reg_invoke_tgrm_call_update(0, 3, 2, 65535, 1, TGRM_CALL_

BUSY, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)

Jun 23 09:54:14: htsp_timer - 10000 msec

Jun 23 09:54:24: htsp_process_event: [0/3/2, FXOGS_WAIT_TIP_GROUND, E_HTSP_EVENT

_TIMER]fxogs_offhook_disc

Jun 23 09:54:24: htsp_timer_stop

Jun 23 09:54:24: [0/3/2] set signal state = 0x4 timestamp = 0

Jun 23 09:54:24: dsp_set_sig_state: [0/3/2] packet_len=12 channel_id=130 packet_

id=39 state=0x4 timestamp=0x0

Jun 23 09:54:24: htsp_timer - 2000 msechtsp_release_req: cause 16, no_onhook 0

Jun 23 09:54:24: htsp_process_event: [0/3/2, FXOGS_ONHOOK, E_HTSP_RELEASE_REQ]fxogs_onhook_release

Jun 23 09:54:24: htsp_timer_stop2

Jun 23 09:54:24: htsp_timer_stop3

Jun 23 09:54:24: TGRM: reg_invoke_tgrm_call_update(0, 3, 2, 65535, 1, TGRM_CALL_

IDLE, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)

Jun 23 09:54:24: flex_dsprm_close_cleanup

Jun 23 09:54:25: htsp_process_event: [0/3/2, FXOGS_ONHOOK, E_DSP_SIG_0110]

Jun 23 09:54:25: fxogs_line_reversal_clid_wait. On_hook line reversal detected possibily due to crossed cable

Jun 23 09:54:26: htsp_process_event: [0/3/2, FXOGS_ONHOOK, E_HTSP_EVENT_TIMER]

Jun 23 09:54:26: [0/3/2, FXOGS_ONHOOK, E_HTSP_EVENT_TIMER] -> ERROR: INVALID INPUT

Thanks

Antonio

paolo bevilacqua · ‎06-25-2007

Hi Antonio,

Where are you located? The port is configured for ground start, but usually ground start is not available outside north america.

How did you "associate" the phone to FXO port ? "connections plar opx", or ?

antonio.dinapoli · ‎06-26-2007

Hi,

I am located in Italy. Actually I have configured the FXO port for ground start and the phone number associated with the FXO port is configured directly on the IP phone.

These are the some configuration's details:

- voice port

voice-port 0/3/2

signal groundStart

cptone IT

impedance complex2

description mysociety_tel

incoming alerting ring-only

caller-id enable

- Two outbound dial peer associated with the voice port 0/3/2

dial-peer voice 7 pots

destination-pattern 0.T

port 0/3/2

forward-digits all

exit

dial-peer voice 8 pots

destination-pattern 3.T

port 0/3/2

forward-digits all

exit

- ephone

ephone-dn 2

number xxxxxxx

name mysociety_tel

ephone 12

keypad-normalize

mac-address xxxx.xxxx.xxxx

type 7911

button 1:2

paolo bevilacqua · ‎06-26-2007

Hi Antonio,

1st, the port must be loop start. There is no ground start support in Italy.

2nd: with fxo ports, you never know what number has been called, it is not sent in signaling.

So you need "connection plar opx " under voice-port. usually you use a local extension number for that, like 2xx.

If you want to be able to direct calls depending on the number called, etc, get ISDN BRi with DID. ("selezione passante" or "multinumero"). Also with ISDN BRI you will have a lot of more features and stability.

Hope this helps, please rate post if it doees!

antonio.dinapoli · ‎06-28-2007

Now it's ok.

I have configured the voice port in loop start with the command "connection plar opx" and I have deleted the command "caller-id enable ".

Thanks

Antonio

paolo bevilacqua · ‎06-28-2007

Glad to know it works. If you have more ports, remember you can put the as "trunk group" and configure a single dial-peer. Plus for your convenience, below a dial-peer set for the italian mobile operators, that will allow only the numbers that are valid according to the prefix. The other advantage is that you can count calls made to each operator with "show dial-peer voice",

Grazie per il rating e buona fortuna!

dial-peer voice 39 pots

trunkgroup colt

description H3G

destination-pattern ^39[0-3].......

no digit-strip

!

dial-peer voice 33 pots

trunkgroup colt

description TIM

destination-pattern ^33[06-9]......T

no digit-strip

!

dial-peer voice 360 pots

trunkgroup colt

description TIM E-TACS

destination-pattern ^33[03-9]......T

no digit-strip

!

dial-peer voice 32 pots

trunkgroup colt

description Wind

destination-pattern ^32[03789].......

no digit-strip

!

dial-peer voice 38 pots

trunkgroup colt

description Wind

destination-pattern ^38[0389].......

no digit-strip

!

dial-peer voice 36 pots

description TIM

destination-pattern ^36[368]......T

no digit-strip

!

dial-peer voice 34 pots

description Vodafone

trunkgroup colt

destination-pattern ^34[036-9].......

no digit-strip