Cisco caller name not appear

[mohamed sebaey]

Hi

I have CUCM integrated with my Ericsson system and i have AA on Ericsson. Ater i get connected to AA , it asks for enter extension number, when i enetered ext number for Cisco IP phone number , i get the call with unknown number. below is my debug for IP phone number 39946?. I used MGCP integration get CUCM and Ercisson.

*Nov 13 12:47:17.863: ISDN Se0/0/1:15 Q931: RX <- SETUP pd = 8  callref = 0x00FB

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech 

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA18394

                Preferred, Channel 20

        Facility i = 0x9FAA068001008201008B0100A1100201010201553008820301B850860101

        Progress Ind i = 0x8183 - Origination address is non-ISDN 

        Called Party Number i = 0x81, '39946'

                Plan:ISDN, Type:Unknown

        Shift to Codeset 4

        Codeset 4 IE 0x31  i = 0x80

debug isdn q931 is              ON.

NGHA-HASA-VG#

*Nov 13 12:47:17.875: ISDN Se0/0/1:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x80FB

        Channel ID i = 0xA98381

                Exclusive, Channel 1

*Nov 13 12:47:17.875: ISDN Se0/0/1:15 Q931: TX -> ALERTING pd = 8  callref = 0x80FB

        Facility i = 0x9FAA06800100820100A10C020101060528EC2C00018400

        Progress Ind i = 0x8088 - In-band info or appropriate now available

*Nov 13 12:47:17.919: ISDN Se0/0/1:15 Q931: RX <- FACILITY pd = 8  callref = 0x00FB

        Facility i = 0x9FAA06800100820100A406020101810101

*Nov 13 12:47:26.851: ISDN Se0/0/1:15 Q931: TX -> CONNECT pd = 8  callref = 0x80FB

        Facility i = 0x9FAA06800100820100A10C020102060528EC2C00028400

        Connected Number i = 0x0081, '39946'

*Nov 13 12:47:26.983: ISDN Se0/0/1:15 Q931: RX <- FACILITY pd = 8  callref = 0x00FB

        Facility i = 0x9FAA06800100820100A406020102810101

*Nov 13 12:47:26.983: ISDN Se0/0/1:15 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x00FB

*Nov 13 12:47:27.659: ISDN Se0/0/1:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x80FB

        Cause i = 0x8090 - Normal call clearing

Thanks

[Gergely Szabo]

Hi,

please make sure you check the "Display IE delivery" checkbox. If it does not work, you may also try the "Send Calling Name In Facility IE" checkbox.

Also, is this Q-Sig?

G.

[mohamed sebaey]

Hi Gergely

Is this under gateway ?. if yes , already done. Yes i use Qsig.Please find my conf under Controller

interface Serial0/0/1:15

no ip address

encapsulation hdlc

isdn switch-type primary-qsig

isdn timer T310 120000

isdn overlap-receiving

isdn protocol-emulate network

isdn incoming-voice voice

isdn supp-service name calling profile Network-Extension operation-value-tag local

isdn bind-l3 ccm-manager

isdn send-alerting

isdn sending-complete

no cdp enable

Thanks

[Gergely Szabo]

Hi,

hmm, I don't have any other clues, really. Sorry about that.

G.

[Carlo Poggiarelli]

Hi.

Can you please indicate the version of cucm you are running?

Thanks

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"