07-08-2015 09:20 AM - last edited on 03-25-2019 08:35 PM by ciscomoderator
Choppy and broken audio.
Any help please?
I was searching Bugs for this and there is not nothing about it.
I was testing with all versions of firmware from cisco web page and i have the same problem with chopping and broken audio.
I have others cisco phones series and the problem only occur with this phone series.
Solved! Go to Solution.
07-08-2015 02:08 PM
I think there are many troubleshooting steps before looking at bugs.
To start with:
- Is this problem with same site or between multiple sites across WAN?
- Locate the source and destination IPs of calling and called endpoints (they can be phones, gateways, or mixsture)
- Look at the routing path between source and destination
- From your monitoring generate bandwidth reports, jitter report, packet loss report for the links using to carry the call between both endpoints.
07-08-2015 10:11 AM
Hi Teodoro,
Could you please refer the bug CSCuq58308
https://tools.cisco.com/bugsearch/bug/CSCuq58308
10.2(1)ES5.2 is the phone firmware which has fixation.
Regards,
Raaj
07-09-2015 01:32 AM
Hello Guys .
Thansk for your answers.
Your version recomended where we can download?
10.2(1)ES5.2
We had tested with all versions availables in cisco:
Below a screen with all versions available in Cisco web page.
07-09-2015 01:54 AM
Hi,
This is engineering special version and only TAC can give you image.
You need to open TAC case for this.
Regards,
Raaj.
07-09-2015 02:47 AM
Hello Rajkumar,please can you send that version firmware by email or any link?
Due metrics, for me is not posible open a case only for this,when the problem is already knowed.
07-09-2015 03:05 AM
Hi Teodoro,
I don't have this firmware.
Sorry.
Regards,
Raaj.
09-22-2015 02:51 AM
hello.
We found that disabling the CDP, the problem was resolved.
Cisco is researching about it.
07-09-2015 05:05 AM
Hi teodoro
A TAC case will be the best option to have the version .
07-18-2015 05:07 PM
I opened a case in Cisco TAc.
We downladed this firmware and aplied but the problem continue.
Taking traces we think that we have a marking packet problem.End user have only AVAYA Switchs.Any QoS recomendation?,exist a manner in that cisco phone not get mark the traffic?.
Any recomendations?
I think that the process of traffic marked ejecuted by Avaya Switch not like to cisco pone RTP process.
Please see my image from 6 calls captureds and which is the cause for end each call.
Among the reasons:
RTP traffic not Market for QoS.
RTP Late packet Arrival.
RTP jitter excesive detected.
07-08-2015 10:40 AM
Communication between phones (RTP) is peer-to-peer and does not go through the CUCM (unless when mixed in a conference). What you are experiencing looks a lot like paket loss. I would look for half duplex links (must be full duplex) in the path between phones, WAN saturation if the two phones are at different locations or activate QoS if the phones are in the same LAN.
07-08-2015 02:08 PM
I think there are many troubleshooting steps before looking at bugs.
To start with:
- Is this problem with same site or between multiple sites across WAN?
- Locate the source and destination IPs of calling and called endpoints (they can be phones, gateways, or mixsture)
- Look at the routing path between source and destination
- From your monitoring generate bandwidth reports, jitter report, packet loss report for the links using to carry the call between both endpoints.
07-09-2015 01:40 AM
-
- Is this problem with same site or between multiple sites across WAN?
--> boths
- Locate the source and destination IPs of calling and called endpoints (they can be phones, gateways, or mixsture).
--> they are private address, we undertands that this no constribute in the solution.
- Look at the routing path between source and destination.
-->We have lost of a 0.9% in the worse case but this is no suffient for contribute in the chopping or broken audio.
- From your monitoring generate bandwidth reports, jitter report, packet loss report for the links using to carry the call between both endpoints.
-->This occur with internal and externall calls.
Attached a report from cucm.
07-09-2015 01:43 AM
we have full duplex speed on the port switch
07-09-2015 01:24 AM
There is bug for 7841 of release 10.1(1)SR1 regarding Poor audio quality and the bug got fixed with the version 10.2(1)ES5.2.
09-22-2015 02:51 AM
hello.
We found that disabling the CDP, the problem was resolved.
Cisco is researching about it.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide