Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Rajkumar Yadav
11-21-2018
Stats
Member since
09-15-2013
324
Posts
123
Helpful
24
Solutions
Created by
Rajkumar Yadav
in IP Telephony and Phones
in IP Telephony and Phones
10-20-2017
10:04 AM
10-20-2017
10:04 AM
Hi, May I know your Router model for this setup ?
... View more
10-20-2017
08:59 AM
Hi,
So far the Session license is RTU license, however as per the datasheet it can be enforced in future version.
Which version you use depends on your existing setup, you may go with 11.X version.
On the CCW we have 10.X, 11.X and 12.X version available for ordering.
How do I license my SME??
SME requires no license, you can simply add the CUCM server to your ELM / PLM server and that would be it, if for any reason you want to use the co-res ELM / PLM to handle only SME, you can order a "SME License" which will be a license with just a few users in it so your SME is considered to be in a valid licensing situation.
Cisco Unified Communications Solutions Ordering Guide
For 9.X/10.X SME systems – no software or node licenses are required, and session licenses are issued as RTU certificates (paper licenses). A SME 9.X/10.X does not require physically installed licenses. However, a SME 9.X/10.X is required to be managed by a registered Enterprise License Manager (ELM) or Cisco Prime License Manager (Cisco Prime LM)
A customer can add a SME system to their product inventory for an ELM/Cisco Prime LM already registered for the customer’s existing CUCM or CUC systems.
A customer can request to register a separate ELM/Cisco Prime LM – only for their registered SME. This is done by contacting licensing@cisco.com and requesting licenses to register there SME ELM/Cisco Prime LM. A nominal amount of UCL Essential licenses will be issued in order to register a separate ELM/Cisco Prime LM used only for SME.
Reference link:
https://www.cisco.com/c/en/us/products/collateral/unified-communications/unified-communications-manager-session-management-edition/data_sheet_c78-684404.html
http://docwiki.cisco.com/wiki/CUCM_FAQ#SME
Regards,
Raaj
... View more
10-17-2017
06:56 AM
Hi,
For CUCM to work as SME you require the SIP session license " SME-SESSION-LIC "
Software will be same as CUCM software.
Please note for below lines where you get default SME license when you have CUWL PRO / UWL meeting license on your CUCM.
One Cisco Unified Communications Manager Session Manager Edition (SME) session license for every 5 UWL-Pro users.
One Cisco Unified Communications Manager Session Manager Edition (SME) session license for every 5 UWL-Meetings users.
Licensing
The basic unit of licensing for Cisco Unified Communications Manager Session Management Edition is number of sessions. In Version 8.0 there is no enforced licensing. Future versions of the application will have licensing enforcement.
â—Â Â Â A session is any SIP, H.323, or SCCP call that exits a trunk in the Cisco Unified Communications Manager Session Management Edition. Examples of sessions include:
◦     Calls that are in tandem with the Cisco Unified Communications Manager Session Management Edition between two different PBXs or clusters
◦     Calls that go from a PBX or cluster to a SIP trunk
◦     Calls that originate from the Cisco Unified Communications Manager Session Management Edition and go to another PBX or trunk
â—Â Â Â Although Cisco Unified Communications Manager Session Management Edition is optimized for PBX aggregation and SIP trunking, it can also register SIP and SCCP phones. Each device (Cisco Unified IP Phones, soft phones, third-party devices, and video devices) provisioned in the system corresponds to a User Connect License (Enhanced IP User, Basic IP User, Public Space, or Analog). Device licensing is enforced in Cisco Unified Communications Manager Session Management Edition.
Regards,
Raaj
... View more
Created by
Rajkumar Yadav
in IP Telephony and Phones
in IP Telephony and Phones
10-17-2017
06:31 AM
10-17-2017
06:31 AM
Hi,
May I know the incoming calling number for both system when outbound call is performed from the PBX system.
From high level view you can use the answer-address command to match the voip incoming dial-peer along with COR-List configuration you can map it to open pots dial-peer which is mapped to its appropriate voice-port / PRI connection.
Regards,
Raaj
... View more
Created by
Rajkumar Yadav
in IP Telephony and Phones
in IP Telephony and Phones
10-17-2017
03:29 AM
10-17-2017
03:29 AM
As I see keeping it separate is always best practice. It helps to achieve priority as well within CSS contained partition.
However in your scenario even if you keep in same internal PT, I think it will hit this first and match the TP rather then going to the PT containing the PSTN RP.
My advice would be separate, however it would work in your scenario with same PT.
Regards,
Raaj
... View more
Created by
Rajkumar Yadav
in IP Telephony and Phones
in IP Telephony and Phones
10-17-2017
02:46 AM
10-17-2017
02:46 AM
Hi,
If you have a CUCM in your setup then just create translation pattern in your cucm.
TP == 0208555[2-7]XXX OR 90208555[2-7]XXX
Partition == TP_PT
Calling Search Space == should be one which contains the partition to dial 6XXXX OR use originator calling search space.
Called party transform mask == 6XXXX
make sure you have the CSS applied on the Phones containing the TP_PT and it should in higher priority list.
In this way the call will remain inside the CUCM always.
Regards,
Raaj
... View more
Created by
Rajkumar Yadav
in IP Telephony and Phones
in IP Telephony and Phones
05-13-2017
10:29 AM
05-13-2017
10:29 AM
For on premises integration please refer the below guides
http://www.cisco.com/c/en/us/solutions/enterprise/interoperability-portal/networking_solutions_products_genericcontent0900aecd805b561d.html
Regards,
Raaj
... View more
05-13-2017
10:25 AM
Hello Rishi,
Have you heard about cloud connector from Microsoft for their customer who are completely on cloud for their S4B setup, still looking for PSTN call from their on premises voice gateway or IPT infra.
Please go through the below link and Micrsoft have a solution for the cloud PBX user to use their on premises gateway.
https://technet.microsoft.com/en-us/library/mt612869.aspx
Skype for Business Cloud Connector Edition - Cloud Connector is a hybrid offering that consists of a set of packaged Virtual Machines (VMs) that implement on-premises PSTN connectivity. By deploying a minimal Skype for Business Server topology in a virtualized environment, users in your organization, whether homed in the cloud are on premises, will be able to send and receive calls with landlines and mobile phones through the existing on-premises voice infrastructure. For more information, see Plan for Skype for Business Cloud Connector Edition and Configure Skype for Business Cloud Connector Edition .
Regards,
Raaj
... View more
05-13-2017
10:17 AM
Hello Victor,
You can use the below third party recording solution for such scenarios.
Such features are not provided from CUCM itself and has to be from third party.
https://www.miarec.com/book/export/html/780
Also check from Imagicle recording solution if they provide the same feature.
Regards,
Raaj
... View more
Created by
Rajkumar Yadav
in IP Telephony and Phones
in IP Telephony and Phones
11-22-2016
04:01 AM
11-22-2016
04:01 AM
Thanks Abdul for confirming, which model did you referenced as part of fast tracking.
Video capability is working fine ? Any issue noticed ?
Regards,
Raaj
... View more
11-22-2016
03:03 AM
Hi Abdul,
Are you able to get those 8845/8865 phones work with CME 11.5 version ?
Please update.
Regards,
Raaj
... View more
08-16-2016
11:56 AM
Gents,
This is now identified as bug and Cisco will be providing the fix in CUCM 12 version ( not sure)
https://bst.cloudapps.cisco.com/bugsearch/bug/CSCva72384/?reffering_site=dumpcr
Symptom: CM 11.5.1 selfcare-page\Conferecing doesnot allow scheduling meeting and gives error message "Conferencing profile not setup". Conditions: Only when clicking "Conferencing" tab in the selfcare portal of the call manager version 11.5.1
Regards,
Raaj
... View more
07-27-2016
10:55 PM
Hi Nishad,
Did you performed any migration of the CUCM and then you facing the issue.
If its like that then you make sure your NTP is in compliance and you have to change the password for the PLM via CLI from OS access.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/plm/10_0_1/userguide/CPLM_BK_U7066CD8_00_user-guide-rel-10-0-1/CPLM_BK_U7066CD8_00_user-guide-rel-10-0-1_appendix_0111.html
Please provide more details and exact behavior you are facing ?
Regards,
Raaj
... View more
07-22-2016
11:03 AM
I think below link should provide you the solution
we have multiple local route group option from CUCM 10 onwards.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/collab10/collab10/dialplan.html#marker-1723776
To support route lists with multiple route group elements specific to the calling device, multiple named local route groups can be configured in Unified CM. After names for all local route groups have been defined on the system level, a route group per named local route group can be configured on the device pool level. This, for example, allows to define different local route groups to be used for emergency calls, national PSTN destinations, and other destinations. Using multiple local route groups enables different gateways to be selected for different types of calls.
Whats your CUCM version ?
Regards,
Raaj
... View more
07-22-2016
10:58 AM
I think you can get the option to have multiple local route group in CUCM device pool page.
You need to add the local route group from local route group option page.
See the attached snapshot from device pool page.
Regards,
Raaj
... View more
Created by
Rajkumar Yadav
in Unified Communications Infrastructure
11-21-2017
11-21-2017
Hi, voice register pool 1 id network 130.9.200.114 mask 255.255.255.252
// this is wrong values for ...
Created by
Rajkumar Yadav
in IP Telephony and Phones
10-20-2017
10-20-2017
Hi, May I know your Router model for this setup ?
10-20-2017
Hi, So far the Session license is RTU license, however as per the
datasheet it can be enforced in fu...
10-17-2017
Hi, For CUCM to work as SME you require the SIP session license
"SME-SESSION-LIC" Software will be s...
10-17-2017
Hi, May I know the incoming calling number for both system when outbound
call is performed from the ...
Created by
Rajkumar Yadav
in IP Telephony and Phones
10-17-2017
10-17-2017
As I see keeping it separate is always best practice. It helps to
achieve priority as well within CS...
Created by
Rajkumar Yadav
in IP Telephony and Phones
10-17-2017
10-17-2017
Hi, If you have a CUCM in your setup then just create translation
pattern in your cucm. TP == 020855...
05-13-2017
For on premises integration please refer the below guides
http://www.cisco.com/c/en/us/solutions/ent...
05-13-2017
Hello Rishi, Have you heard about cloud connector from Microsoft for
their customer who are complete...
05-13-2017
Hello Victor, You can use the below third party recording solution for
such scenarios. Such features...
Created by
Rajkumar Yadav
in TelePresence and Video Infrastructure
05-13-2017
05-13-2017
I have used IIS before and it works fine. Regards, Raaj
05-13-2017
Hi, You would require the RMS license on EXP-E and on CMS call bridge
license should be sufficient t...
05-08-2017
Hello Ahmed, I would suggest to go towards Cisco preferred approach to
achieve the federation with o...
Created by
Rajkumar Yadav
in TelePresence and Video Infrastructure
05-03-2017
05-03-2017
Are you talking about the PSTN calls ? Please share the exact details
for this calls. If its PSTN ca...
Public Statistics
| Date Registered | 09-15-2013 12:12 AM |
| Date Last Visited | 11-21-2018 10:24 PM |
| Total Messages Posted | 324 |
| Total Helpful Votes Received | 123 |
Helpful Votes Given To
Helpful Votes From
