10-09-2018 12:45 AM - edited 03-17-2019 01:33 PM
Hello All,
We have Cisco VG 350 we have configured with SCCP protocol with CUCM 11.5 but we are not getting it registered with cucm.
Note: We have not yet connected and configured analog FXS ports in it.
Please suggest if there is any command to check registration status with CUCM on VG 350 gateway because on CUCM it is not showing the gateway status.
Thank You.
Solved! Go to Solution.
10-09-2018 10:19 AM
10-09-2018 02:46 AM
10-09-2018 05:03 AM
10-09-2018 05:17 AM
Hi,
You do not have the complete configuration done on the gateway.
Follow this doc:
Hope this helps.
Bijo
10-09-2018 06:02 AM
Does it mean that if i configure fxt port and connect analog Phone to it then only it will get show VG350 status register on CUCM?
Sachin
10-09-2018 07:00 AM
10-09-2018 09:17 AM
I have followed the document and i found Gateway is register with CUCM but on CUCM side it is still not showing register status.
Note: I have configured FXS port in the router but still have not connected analog phone to it as i have no Cable to connect to it.
Please find below out which shows some " Error History "
V350G#sh ccm-manager config-download
SCCP auto-configuration status
===============================================================
Registered with Call Manager: Yes
Local interface: GigabitEthernet0/0 (00ae.7591.ed00)
Current version-id: 1539099402-d6323c0b-f334-492f-b467-72464d31bd7b
Current config applied at: 21:06:52 GMT Oct 9 2018
Gateway downloads succeeded: 9
Gateway download attempts: 9
Last gateway download attempt: 21:21:43 GMT Oct 9 2018
Last successful gateway download: 21:21:43 GMT Oct 9 2018
Current TFTP server: 172.30.17.7
Gateway resets: 3
Gateway restarts: 3
Managed endpoints: 0
Endpoint downloads succeeded: 0
Endpoint download attempts: 0
Last endpoint download attempt: None
Last successful endpoint download: None
Endpoint resets: 0
Endpoint restarts: 0
Configuration Error History:
stcapp ccm-group 1
stcapp
end
and
VG350#sh run | se voice
voice-card 0
voice-port 2/0/0
voice-port 2/0/1
voice-port 2/0/2
voice-port 2/0/3
voice-port will automatically get configured by CUCM?
i found no Voice-Port and dial-peer configured in VG350.
Thank You for your prompt reply.
Sachin S
10-09-2018 03:01 AM
10-09-2018 09:51 AM
Hi bijo,
Please find attached show run and below required output. I have configured of the port 2/0/0 in cucm.
=============================================================================================
sh sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 172.30.17.11
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 172.30.17.8, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 2
Trustpoint: N/A
Call Manager: 172.30.16.7, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 1
Trustpoint: N/A
AutoCfg_Virtual_Endpoint Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 172.30.17.7, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: ANBE7591FC00FFF
Reported Max Streams: 0, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 20
=================================================================================================
sh stcapp dev summ
VG350#sh stcapp dev summ
Total Devices: 0
Total Calls in Progress: 0
Total Call Legs in Use: 0
Port Device Device Call Dev Directory Dev
Identifier Name State State Type Number Cntl
---------- --------------- -------- ------------- ------- ----------- ----
VG350#
Thanks,
Sachin Shinde.
10-09-2018 10:19 AM
10-09-2018 11:34 AM
Hi bijo,
Thank You for your prompt reply and support.
I have configured Dial-peer in the VG 350 and found Voice-port 2/0/0 is registered with my CUCM. PFA
Below are my few queries,
Do i have to manually configure pots Dial-Peer for every analog port on VG350?
Still VG350 Gateway shows unregister on CUCM ? Refer VG0nCUCM attachment.
Voice-Port 2/0/0 still not connected to Analog Phone but on Phone page it shows registered with CUCM?
Once again thanks for your great help...
Sachin Shinde
10-10-2018 02:31 AM
10-10-2018 02:37 AM
10-11-2018 12:00 AM - edited 10-11-2018 03:17 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide