06-15-2018 07:16 AM - edited 03-17-2019 01:01 PM
Hello all,
I try to configure E1 fllow on my CME (3800 Software (C3845-ADVENTERPRISEK9-M), Version 15.1(4)M3)
I configured:
card type e1 0 1 ! card type command needed for slot/vwic-slot 0/3 isdn switch-type primary-net5 ! voice-card 0 dspfarm dsp services dspfarm ! ! voice rtp send-recv ! voice service pots ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to sip sip registrar server expires max 600 min 60 ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 codec preference 4 g729br8 ! controller E1 0/1/0 framing NO-CRC4 pri-group timeslots 1-31 !interface Serial0/1/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice no cdp enable ! voice-port 0/1/0:15 !
1#sh controllers E1 E1 0/1/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20100222, FPGA: 13, spm_count = 0 Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line. Data in current interval (742 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 57 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 57 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 24 hours) 0 Line Code Violations, 0 Path Code Violations, 6674 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 6674 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
When i try to call on one of my PSTN number, I hear shortly bib.
Could you please indicate me on mistake or/and indicate documentation/guide about this, please?
06-15-2018 08:47 AM
06-15-2018 12:24 PM
Not, it is configure on clear system
#sh isdn status Global ISDN Switchtype = primary-net5 ISDN Serial0/1/0:15 interface dsl 0, interface ISDN Switchtype = primary-net5 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0xFFFF7FFF Number of L2 Discards = 0, L2 Session ID = 30 Total Allocated ISDN CCBs = 0
06-15-2018 12:25 PM
06-18-2018 12:58 AM
I added debug commands, but debug messages i not see.
If i call on one number communication at once are closes (is heard shortly beep), if i call on another number from E1 flow i hear long beep (as normal call when long time no answer on call), but logging messages i not see as before.
06-18-2018 07:17 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide