CME forced auth codes in 8.5/8.6

[thisisshanky]

I m referring to this document (which doesnt seem to help me much)..so thought of posting at this forum....

Has any body successfully implemented FAC in CME..

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmefac.html

i have setup two LPCor groups one for end users and one for PSTN trunks..to test this functionality i put one ephone under the end users group and another ephone in the PSTN trunk group..and when you call from ephone 1 to 2...it asks for the username and password as programmed but then it hangs up the call...

i can post configs if needed...its pretty similar to whats in the document..

TIA..

[Praveen Arak]

Dear Team ,

                 Can any body please provide guidance  for single one time pin authentication for LP COR FAC in CME 9.x . Do please suggest and advise doe the best .

Regards

Praveen

[mraj_ Seed]

hi Shanky,

am facing issue with this config, the audio file are not on my root flash, will it work ?

[Venkitesh H Iyer]

Hello All,

I think this link will help you resolve all your issues.

https://supportforums.cisco.com/discussion/11147326/how-get-lpcor-working-cme-85

It also contains the 123630-FAC-SBCS.zip file that contains the audio files, that will make the LPCOR work.

Trust this helps.

Let me know, if any of you face any issues.

Regards,

Venkitesh

[asotojimenezz]

Hello everyone

I need help.which is my mistake ??

aaa new-model
aaa authentication login default local
aaa authentication login h323 local
aaa authorization exec h323 local
aaa authorization network h323 local

gw-accounting aaa
aaa session-id common

 

trunk group Telmex-E1
 hunt-scheme least-idle

voice lpcor enable
voice lpcor custom
 group 10 end-user
 group 11 pstntrunk
!
voice lpcor policy end-user
 service fac
 accept end-user fac
 accept pstntrunk fac
!
voice lpcor policy pstntrunk
 service fac
 accept end-user fac
 accept pstntrunk fac

application
 package auth
  param passwd-prompt flash:enter_pin.au
  param max-retries 0
  param passwd 1973285
  param abort-digit *
  param user-prompt flash:enter_account.au
  param term-digit #
  param max-digits 32

username 1 password 0 91724
username 2 password 0 50476
username 3 password 0 87123
username 4 password 0 98237
username 5 password 0 10568
username 6 password 0 29561
username 7 password 0 56102
username 8 password 0 43875
username 9 password 0 87325
username 10 password 0 31854
username 11 password 0 69425
username 12 password 0 79161
username 13 password 0 94989
username 14 password 0 65443

controller E1 0/0/0
 framing NO-CRC4
 line-termination 75-ohm
 ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani
 cas-custom 0
  country telmex
  category 2
  answer-signal group-b 1
  caller-digits 4
  dnis-digits min 4 max 13
  dnis-complete        
  timer interdigit incoming 1000
  groupa-callerid-end
  trunk-group Telmex-E1

dial-peer voice 921 pots
 trunkgroup Telmex-E1
 corlist outgoing CallCelularLocal
 destination-pattern 9044..........
 incoming called-number 9044..........
 direct-inward-dial
 prefix 044
!
dial-peer voice 931 pots
 trunkgroup Telmex-E1
 corlist outgoing CallCelularNacional
 destination-pattern 9045..........
 incoming called-number 9045..........
 direct-inward-dial
 prefix 045
!
dial-peer voice 941 pots
 trunkgroup Telmex-E1
 corlist outgoing CallLD-Nacional
 destination-pattern 901..........
 incoming called-number 901..........
 direct-inward-dial
 prefix 01

voice register pool  2
 pin 50476
 lpcor type local
 lpcor incoming superuser
 busy-trigger-per-button 2
 id mac 547C.69D7.6706
 type 7841
 number 1 dn 2
 cor incoming Nivel3 default
 presence call-list
 dtmf-relay rtp-nte sip-notify
 username 2 password 50476
 description 7841
 codec g711ulaw

Regards.

[Amit23]

how can apply FAC as we have SIP trunk with cme 10.5?

what would change in configuration for FAC in CME?

[Jaime Terrazas Dominguez]

Please review this link for the explanation

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmelpcor.html#46541

SUMMARY STEPS

1. enable

2. configure terminal

3. voice lpcor ip-trunk subnet incoming

4. index index-number lpcor-group { ipv4-address network-mask | hostname hostname }

5. exit

6. voice service voip

7. lpcor incoming lpcor-group

8. exit

9. dial-peer voice tag voip

10. lpcor outgoing lpcor-group

11. end

Examples

The following example shows a LPCOR configuration for VoIP trunks:

voice lpcor ip-trunk subnet incoming

index 1 h323_group1 172.19.33.0 255.255.255.0

index 2 sip_group1 172.19.22.0 255.255.255.0

index 3 sip_group2 hostname sipexample

!

voice service voip

lpcor incoming voip_trunk_1

!

dial-peer voice 233 voip

description H323 trunk outbound dial-peer

destination-pattern 233T

session target ipv4:172.19.33.233

lpcor outgoing h323_group1

!

dial-peer voice 2255 voip

description SIP trunk outbound dial-peer

destination-pattern 255T

session protocol sipv2

session target ipv4:172.19.3