07-18-2012 06:07 AM - edited 03-16-2019 12:15 PM
Hi
i am having a setup with cme ver 8.6 and 3 fxo lines .some time even all the lines are free also user will not be able to make the call it will give busy tone that time i use to shut and no shut the fxo port it will work .Please help me how to resole the issue . i here attached the config below
voice call send-alert
voice rtp send-recv
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 timeout setup 5
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
!
voice class dualtone-detect-params 1
freq-max-deviation 20
cadence-variation 20
!
voice class custom-cptone UAE-CPTONE
dualtone disconnect
frequency 400 405
cadence 380 380 400 350 225 525
!
!
!
!
!
license udi pid CISCO2911/K9 sn FCZ1540700Z
hw-module pvdm 0/0
!
!
!
username admin password 0 cisco
!
redundancy
!
!
!
translation-rule 9
Rule 1 ^00 900
Rule 2 ^02 9
Rule 3 ^03 903
Rule 4 ^04 904
Rule 5 ^05 905
Rule 6 ^06 906
Rule 7 ^07 907
Rule 8 ^08 908
Rule 9 ^09 909
!
!
!
!
!
i
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
description *** Voice Gateway ****
ip address 192.168.50.4 255.255.255.0
ip pim dense-mode
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr 192.168.50.4
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:
!
ip route 0.0.0.0 0.0.0.0 192.168.50.250
!
access-list 23 permit 10.10.10.0 0.0.0.7
voice-port 0/0/0
trunk-group FXOPORTS
translation-profile incoming incomming
translate calling 9
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CPTONE
supervisory dualtone-detect-params 1
input gain 14
compand-type a-law
cptone AE
timeouts call-disconnect 1
timeouts wait-release 1
connection plar opx 5000
shutdown
caller-id enable
!
voice-port 0/0/1
trunk-group FXOPORTS
translation-profile incoming incomming
translate calling 9
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CPTONE
supervisory dualtone-detect-params 1
input gain 14
compand-type a-law
cptone AE
timeouts call-disconnect 1
timeouts wait-release 1
connection plar opx 5000
caller-id enable
!
voice-port 0/0/2
trunk-group FXOPORTS
translation-profile incoming incomming
translate calling 9
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CPTONE
supervisory dualtone-detect-params 1
input gain 14
compand-type a-law
cptone AE
timeouts call-disconnect 1
timeouts wait-release 1
connection plar opx 5000
caller-id enable
!
voice-port 0/0/3
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CPTONE
supervisory dualtone-detect-params 1
input gain 14
compand-type a-law
cptone AE
timeouts call-disconnect 1
timeouts wait-release 1
connection plar opx 5001
description **** MANAGER DIRECT LINE ****
caller-id enable
Solved! Go to Solution.
07-18-2012 07:16 AM
Hi,
Also remove the compound type from your FXO analogue voice ports as this can cause issues.
The compound type is used for digital technology like ISDN/BRI
!
voice-port 0/0/0
no compand-type a-law
!
voice-port 0/0/1
no compand-type a-law
!
voice-port 0/0/2
no compand-type a-law
!
voice-port 0/0/3
no compand-type a-law
!
Regards,
Alex.
Please rate useful posts.
07-18-2012 06:55 AM
Most likely, your custom cptone configuration is incorrect.
07-18-2012 07:16 AM
Hi,
Also remove the compound type from your FXO analogue voice ports as this can cause issues.
The compound type is used for digital technology like ISDN/BRI
!
voice-port 0/0/0
no compand-type a-law
!
voice-port 0/0/1
no compand-type a-law
!
voice-port 0/0/2
no compand-type a-law
!
voice-port 0/0/3
no compand-type a-law
!
Regards,
Alex.
Please rate useful posts.
07-18-2012 07:23 AM
Hi
Thanks paolo
Do you have any sample config for CPtone for UAEregion
07-18-2012 07:35 AM
Raja,
Try this website
http://www.3amsystems.com/wireline/tone-search.htm
Select your country and tone
You can only search once a day or something like that so get it right 1st time
Regards,
Alex.
Please rate useful posts.
07-18-2012 08:32 AM
You will need to record the tone and analyze.
I used to have a router in Dubai, but i think I've since lost its configuration.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: