cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Walkthrough Wednesdays
930
Views
0
Helpful
1
Replies
Highlighted
Beginner

h.323 gw& Invalid number format

Hello!

i have cisco2911 with 151-4.M3 IOS, gateway configured as h.323 gw on Cisco CUCM.

when i made outside call to PSTN from IP phone i got message

Invalid number format

after

TX -> INFORMATION which gw send to PSTN

Aug 14 05:31:25.359: ISDN  Se0/0/0:15 Q931: Sending SETUP  callref = 0x00F4 callID = 0x8077 switch =  primary-net5 interface = User

Aug 14 05:31:25.359: ISDN  Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F4

        Bearer Capability  i = 0x8090A3

                Standard  = CCITT

                Transfer  Capability = Speech

                Transfer  Mode = Circuit

                Transfer  Rate = 64 kbit/s

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

        Progress Ind i = 0x8183 - Origination address is  non-ISDN

        Calling Party  Number i = 0x2181, '8xxx420494'

                 Plan:ISDN, Type:National

        Called Party  Number i = 0xA1, '8xxx3815299'

                 Plan:ISDN, Type:National

Aug 14 05:31:25.379: ISDN  Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x80F4

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

Aug 14 05:31:25.379: ISDN  Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x80F4

        Progress Ind i = 0x8288 - In-band info or appropriate  now available

Aug 14 05:31:28.959: ISDN  Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref =  0x80F4

Aug 14  05:31:35.359: ISDN Se0/0/0:15 Q931: TX -> INFORMATION pd = 8  callref =  0x00F4

         Sending Complete

Aug 14 05:31:35.371: ISDN  Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x80F4

       Cause i = 0x829C  - Invalid number format (incomplete number)

         Progress Ind i = 0x8288 - In-band info or appropriate  now available 

         Display i = 'WRONG NUMBER '

But if i push button "Redial" on IP phone call go with out problem and i don't see message

Aug 14  05:31:35.359: ISDN Se0/0/0:15 Q931: TX -> INFORMATION pd = 8  callref =  0x00F4

          Sending Complete

Aug 14 05:32:01.838: ISDN  Se0/0/0:15 Q931: Sending SETUP  callref = 0x00F5 callID = 0x8078 switch =  primary-net5 interface = User

Aug 14 05:32:01.838: ISDN  Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F5

        Bearer Capability  i = 0x8090A3

                Standard  = CCITT

                Transfer  Capability = Speech 

                Transfer  Mode = Circuit

                Transfer  Rate = 64 kbit/s

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

        Progress Ind i = 0x8183 - Origination address is  non-ISDN 

        Calling Party  Number i = 0x2181, '8xxx420494'

                 Plan:ISDN, Type:National

        Called Party  Number i = 0xA1, '8xxx3815299'

                 Plan:ISDN, Type:National

Aug 14 05:32:01.854: ISDN  Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x80F5

        Channel ID i =  0xA9838A

                 Exclusive, Channel 10

Aug 14 05:32:01.858: ISDN  Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x80F5

        Progress Ind i = 0x8288 - In-band info or appropriate  now available

Aug 14 05:32:05.106: ISDN  Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref =  0x80F5

Aug 14 05:32:17.714: ISDN  Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x80F5

        Cause i = 0x8391  - User busy

        Progress Ind i = 0x8288 - In-band info or appropriate  now available 

        Display i = 'BUSY

How to get rid of INFORMATION message?

Best regards,

Mike

1 REPLY 1
Highlighted
Hall of Fame Master

Is the 8 part of the number or the prefix? Post your dial peer configuration.

Chris

Content for Community-Ad