Hello,
I have a problem configuring the IP Phones, I register the post, in CUCM, and when I plug the IP Phone into the Switch, the station does not recover its network configuration, I give you the elements of my Lab: CUCM 11.5, Cisco ROuter 2901, Catalyst 2960 PoE Switch, and IP Phone 7911,
Here is the configuration of my Router (my Router configured also as DHCP and DNS Server) :
hostname GATEWAY-VOIP
!
boot-start-marker
boot-end-marker
!
!
! card type command needed for slot/vwic-slot 0/0
logging buffered 51200 warnings
!
no aaa new-model
bsd-client server url https://cloudsso.cisco.com/as/token.oauth2
!
ip dhcp excluded-address 10.2.7.1
ip dhcp excluded-address 10.2.7.2
ip dhcp excluded-address 10.2.7.3
ip dhcp excluded-address 10.2.10.10
ip dhcp excluded-address 10.2.10.11
ip dhcp excluded-address 10.2.10.12
ip dhcp excluded-address 10.2.10.13
ip dhcp excluded-address 10.2.10.14
ip dhcp excluded-address 10.2.10.15
ip dhcp excluded-address 10.2.10.1
ip dhcp excluded-address 10.2.10.2
ip dhcp excluded-address 10.2.10.3
!
ip dhcp pool dpool1
import all
network 10.2.7.0 255.255.255.0
default-router 10.2.7.12
dns-server 10.2.7.12
domain-name cisco.ma
exit
ip dhcp pool dpool2
import all
network 10.2.10.0 255.255.255.0
default-router 10.2.7.12
dns-server 10.2.7.12
domain-name cisco.ma
!
no ip domain lookup
ip domain name cisco.ma
ip name-server 10.2.7.12
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
voice-card 0
!
!
voice call send-alert
!
voice service voip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
session transport udp
!
voice class h323 1
call start fast
!
license udi pid CISCO2901/K9 sn FGL204610JC
hw-module pvdm 0/0
!
username admin privilege 15 password 7 06350E2D491C594852
!
redundancy
!
ip ssh time-out 50
ip ssh authentication-retries 4
ip ssh version 2
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 10.2.7.12 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
ip forward-protocol nd
!
no ip http server
ip http access-class 23
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip dns server
ip route 0.0.0.0 0.0.0.0 10.2.7.1
!
control-plane
!
voice-port 0/1/0
timeouts interdigit 4
connection plar opx 1111
caller-id enable
!
voice-port 0/1/1
timeouts interdigit 4
connection plar opx 1111
caller-id enable
!
voice-port 0/1/2
timeouts interdigit 4
connection plar opx 1100
caller-id enable
!
voice-port 0/1/3
timeouts interdigit 4
connection plar opx 1100
caller-id enable
!
dial-peer voice 1 voip
destination-pattern 1...
progress_ind setup enable 3
session target ipv4:10.2.7.13
incoming called-number 0T
codec g711ulaw
no vad
!
dial-peer voice 2 pots
preference 1
destination-pattern 0T
port 0/1/0
forward-digits all
!
dial-peer voice 3 pots
preference 2
destination-pattern 0T
port 0/1/1
forward-digits all
!
dial-peer voice 4 pots
preference 3
destination-pattern 0T
port 0/1/2
forward-digits all
!
dial-peer voice 5 pots
preference 4
destination-pattern 0T
port 0/1/3
forward-digits all
gatekeeper
shutdown
!
line con 0
login local
line aux 0
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
ntp master 3
!
end
/////////////////////////// ********
The configuration of my Switch is in join with the screens of the configuration of IP Phone to the CUCM,
thank you for helping me
