03-07-2017 10:45 AM - edited 03-17-2019 09:44 AM
Hi Experts,
.:: I'm getting a weird issue. MGCP FXS Port at VG224 shows 'Registered' at the Call Manager. But the Analog phone connected at the port is not able to receive any incoming calls. Getting Fast busy tone while dialing the Analog phone's number. There is no dial tone to dial outside as well.
.:: After logging in to VG224, I'm able to see the status of the port is 'fxs-ls up up on-hook idle y', it stuck at the 'UP' status. The ideal status would be 'dorm', but this port is not going to the 'dorm' state. FXS port stuck at UP state.
.:: Affected port (2/0/- 24, 30, 35, 38,41), all other ports are working fine.
Network Setup:-
CUCM Cluster <-----(MGCP)-----> VG224 FXS Port
VGXXXXXXX#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
.
2/0/22 -- fxs-ls up dorm on-hook idle y
2/0/23 -- fxs-ls up dorm on-hook idle y
2/0/24 -- fxs-ls up up on-hook idle y
2/0/25 -- fxs-ls up dorm on-hook idle y
.
2/0/29 -- fxs-ls up dorm on-hook idle y
2/0/30 -- fxs-ls up up on-hook idle y
2/0/31 -- fxs-ls up dorm on-hook idle y
.
2/0/34 -- fxs-ls up dorm on-hook idle y
2/0/35 -- fxs-ls up up on-hook idle y
2/0/36 -- fxs-ls up dorm on-hook idle y
2/0/37 -- fxs-ls up dorm on-hook idle y
2/0/38 -- fxs-ls up up on-hook idle y
2/0/39 -- fxs-ls up dorm on-hook idle y
2/0/40 -- fxs-ls up dorm on-hook idle y
2/0/41 -- fxs-ls up up on-hook idle y
2/0/42 -- fxs-ls up dorm on-hook idle y
Troubleshooting Steps followed:-
.:: Reset MGCP FXS Port at the Call Manager
.:: Shut no shut at the VG224 voice-port (2/0/- 24, 30, 35, 38,41). Even after having 'shutdown', the Admin status and Oper Status was 'UP'
.:: Removed and reconfigured the MGCP Dial-Peer (dial-peer voice 151511 pots, service mgcpapp, port 2/0/38)
Please suggest further troubleshooting steps.
Regards,
Jaseem
03-07-2017 11:39 AM
One the first glance, it appears to be a bug, could you please post the config as well as the running version of the IOS on the VG224
HTH
Plz rate all helpful posts
03-08-2017 03:28 AM
Hi Wilson,
Thanks for the update.
XXXXXX#show version
Cisco IOS Software, VG350 Software (VG350-UNIVERSALK9-M), Version 15.4(3)M6, REL EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 18-Aug-16 03:21 by prod_rel_team
Configuration file attached.
04-17-2017 01:34 PM
Hi,
I am facing the same issue with VG224: fxs ports are stuck in the "up" state and getting "fast busy tone" while dialing the analog phone number.
2/10 -- fxs-ls up up on-hook idle y
2/11 -- fxs-ls up up on-hook idle y
2/12 -- fxs-ls up up on-hook idle y
2/13 -- fxs-ls up up on-hook idle y
CUCM: 11.X
VG224: Version 12.4(6)T
Is there any compatability issue between CUCM11 and VG224 current software version?
Regards
Mishab
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide