cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1301
Views
0
Helpful
5
Replies

No entran llamadas al telefono analogico conectado a la tarjeta FXS

Tengo un router cisco 20801 con una tarjeta FXS de dos puertos y una FXO de 4 puertos. Dos telefonos analógicos estan conectados a la tarjeta FXS (uno a cada puerto) con sus respectivas extenciones. Estos telefonos pueden realizar llamadas hacia los telefonos IP (de la misma localidad y las demas sedes) y hacia la PSTN. Pero no entra ningun tipo de llamada.

Espero me puedan explicar a que se debe esto. Cabe destacar que la configuración esta exactamente igual a otras sedes donde si funcionan correctamente las llamadas (tanto entrantes como salientes) de los telefonos analogicos conectados a la FXS, será posible que sea problemas en la tarjeta?

Espero su pronta respuesta

Saludos!

5 Replies 5

Chris Deren
Hall of Fame
Hall of Fame

Please post your config and ensure you have dial-peers pointing to the FXS lines.

HTH,

Chris

Esta es parte de la configuracion del router.

voice-port 0/0/0          Tarjeta FXS

no battery-reversal

cptone VE

!

voice-port 0/0/1

no battery-reversal

cptone VE

!

voice-port 0/2/0     Todos los puertos FXO estan configurados igual    

trunk-group FXO

supervisory disconnect dualtone mid-call

supervisory custom-cptone Venezuela

supervisory dualtone-detect-params 1

no battery-reversal

echo-cancel coverage 24

no vad

cptone VE

timeouts initial 5

timeouts call-disconnect 5

timeouts ringing 30

timeouts wait-release 5

timing guard-out 300

connection plar opx 412701

description LINEA CANTV

station-id name Linea 1

dial-peer voice 101 pots

trunkgroup FXO

voice cut-through alert

description ** Llamadas Locales **

destination-pattern 9[2-9]......

forward-digits 7

!        

dial-peer voice 102 pots

trunkgroup FXO

voice cut-through alert

description ** Llamadas Nacionales **

destination-pattern 902.........

forward-digits 11

!

dial-peer voice 103 pots

trunkgroup FXO

voice cut-through alert

description ** Llamadas Celulares **

destination-pattern 904[1-2]........

forward-digits 11

!

dial-peer voice 104 pots

trunkgroup FXO

voice cut-through alert

description ** LLamadas 0500 **

destination-pattern 90500.......

forward-digits 11

!

dial-peer voice 105 pots

trunkgroup FXO

voice cut-through alert

description ** LLamadas 1XX **

destination-pattern 91..

forward-digits 3

!

dial-peer voice 106 pots

trunkgroup FXO

voice cut-through alert

description ** LLamadas 0800 **

destination-pattern 90800.......

forward-digits 11

!

dial-peer voice 107 pots

trunkgroup FXO

voice cut-through alert

description ** LLamadas Internacionales **

destination-pattern 9T

forward-digits 13

!

dial-peer voice 201 voip

description ** Ruta hacia telefonos IP **

preference 1

destination-pattern 4.....

session target ipv4:172.16.20.12

dtmf-relay h245-alphanumeric

ip qos dscp cs5 media

dial-peer voice 401 pots

description ** Local FAX **

service mgcpapp

port 0/0/0

dial-peer voice 402 pots

description ** Local Garita **

service mgcpapp

port 0/0/1

So, FXS ports are controlled via MGCP, are the FXS ports registered in CUCM? 

What is the extension of the FXS port? Is it 412701 as that is what your FXO trunk points to?

Chris

Si los puertos FXS estan registrados en el call manager. Las estenciones asignadas son 412704 y 412706.

OK, noteice your FXO port points only to 412701:

voice-port 0/2/0     Todos los puertos FXO estan configurados igual    

connection plar opx 412701

So, unless you have translation pattern in CUCM that translates 412701 to 412704 or 412706 it will not  get to ehe FXS ports.

HTH,

Chris