12-31-2007 08:50 AM - edited 03-15-2019 08:00 AM
hello,
i have a router 2851 with FXO and FXS .
i want that statios behind FXS can't call outside through FXO.
thanks at advance.
12-31-2007 09:00 AM
See:
http://cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
Note: the actual configuration can be made smaller that in the example. Just configure with cor the incoming DP for FXS (if not using FXS in SCCP mode), and the DP matching FXO.
Hope this helps, please rate post if it does!
12-31-2007 09:03 AM
hi,
thanks for reply
but i don't have CME to configure COR.
thanks again.
12-31-2007 09:17 AM
Do you have CM? And if so which protocol are you using to the router ?
12-31-2007 09:22 AM
hi,
i have CCM 5.1 and i use H323 protcol.
thanks very much
12-31-2007 09:29 AM
Then he COR configuration still applies. Set a "station number" under voice-port and match it with "answer-address" on a pots DP. That will be your incoming DP.
Another technique is that you configure a translation profile again on the FXS voice port, and change the called number so that it can't dial outside.
12-31-2007 10:14 AM
hi,
it doesn't work
can you troubleshhot the config :
dial-peer cor custom
name FXS
name All
!
!
!
dial-peer cor list Test
member FXS
!
dial-peer cor list ALL
member All
!
!
!
!
!
dial-peer voice 2 pots
corlist outgoing ALL
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/2
!
dial-peer voice 3 pots
corlist outgoing ALL
preference 1
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/3
!
dial-peer voice 4 pots
corlist outgoing ALL
preference 2
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
!
dial-peer voice 5 pots
corlist outgoing ALL
preference 3
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
!
dial-peer voice 52 pots
corlist outgoing Test
answer-address 6211
port 2/0/0
thanks at advance
12-31-2007 10:28 AM
Hi,
1. DP 52 needs corlist incoming, not outgoing
2. DP 52 does not need port
3. Have you set station number under voice port 2/0/0 ?
4. unrelated to the problem, you don't need any of the progress_ind commands under DP, these are for ISDN only, and not even always.
5. suggest you use trunkgroup for port 0/0/2, 0/0/3, and 0/1/0 ? That will allow you using a single DP, simplifying much the configuration.
12-31-2007 10:45 AM
hello,
thank you vey much for your help and also your advices.
You are Wonderful.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide