cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
289
Views
0
Helpful
2
Replies

PRI GW can't incoming call

bo liu
Level 4
Level 4
hi
 
i config a pri GW ,the GW connect to CUCM use H323
 
when i call a pstn phone ,is all right
 
but when i call the internal call from PSTN,i will receive next  signaling 
 
 
Mar 17 11:17:10.848: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x0F3A 
Sending Complete 
Bearer Capability i = 0x9090A3 
Standard = CCITT 
Transfer Capability = 3.1kHz Audio 
Transfer Mode = Circuit 
Transfer Rate = 64 kbit/s 
Channel ID i = 0xE9808382 
Exclusive, Interface 0, Channel 2 
Calling Party Number i = 0x2181, '01059631079' 
Plan:ISDN, Type:National 
Called Party Number i = 0xC1, '03167153777' 
Plan:ISDN, Type:Subscriber(local)
*Mar 17 11:17:10.852: ISDN Se0/0/0:15 Q931: Received SETUP  callref = 0x8F3A callID = 0x0002 switch = primary-net5 interface = User 
*Mar 17 11:17:10.852: ISDN Se0/0/0:15 **ERROR**: CCPMSG_InCall: ChannelID IE invalid 100(0x64) rejecting call
*Mar 17 11:17:10.852: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8F3A 
Cause i = 0x80E418 - Invalid information element contents
 
 
but when i change the GW protocol to MGCP the GW is all right
 
next is my GW  version
 

Cisco IOS Software, 3800 Software (C3845-ADVENTERPRISEK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 25-Feb-09 23:13 by prod_rel_team

ROM: System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)

baihegw uptime is 2 weeks, 5 days, 10 hours, 49 minutes
System returned to ROM by power-on
System image file is "flash:c3845-adventerprisek9-mz.124-24.T.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 3845 (revision 1.0) with 746495K/39936K bytes of memory.
Processor board ID FHK1413F0PZ
2 Gigabit Ethernet interfaces
31 Serial interfaces
2 Channelized/Clear E1/PRI ports
2 Channelized (E1 or T1)/PRI ports
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
250880K bytes of ATA System CompactFlash (Read/Write)

2 Replies 2

kkoeper12
Level 3
Level 3

Can you post the config and a debug of an outgoing call that works?

 

 

I am facing this issue on MGCP router .I can call out to the PSTN but incoming calls gives the same error.

I am using E1 PRI and switch type is set to EURO

.

Could it be because of switch type ?

Cause i = 0x80E418 - Invalid information element contents

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: